Just a dirt pusher. Final trim and and a water binder and there cutting to tolerances is a gun operated I should know my old man was one. No Lazer bullshit he needed
*SKILLED!? Are you kidding me!? This is a What Not to do video. Blade speed is Twice what should be (he’s BOUNCING!) , putting the windrow back into the previous cut, making passes on top of passes with NO SIGHNS of ANYONE OR ANYTHING checking grade (WHERE ARE THE GRADE STAKES!?) and the list goes on…*
15 seconds into the video I can tell you that this is NOT a skilled operator. At best he is just a "driver". Watch the machine bounce. He is traveling too fast. Improper machine placement, improper circle and moldboard position, no wheel lean. Pushing a large windrow, he should have had some articulation.
@@alanlambert-bz4to Then why didn't this "teacher" tell him to slow down? Plus all the other things he was doing that needed attention. Believe me, I know that there are no two operators that do things all the same way, but there are things that ARE standard techniques. Those are all things that his teacher should have been addressing. You could read some of the other comments, and they were saying basically the same as I was. Some were nicer than I was in their critique, some weren't. I mean if your video is going to say "Amazing operating techniques, skilled operator", you should have had the "teacher" operating.
A good blade man never lets tailings roll off the leading edge of his blade…maybe if you are bulking and hitting piles but never when you’re finishing…this guy is doing good for just learning but he’s not an experienced finisher by any means!..these are the things you must go through as you learn…I was there too when I first started!..
A skilled grader operator makes sure the mole board is rolled back all the way, the machine stays intimate with the surface and there’s always material rolling off the end of the blade. This guy is a rookie at best.
Yeah that is just some dude that learned what lever did what and jumped out there lol and the guys on the rollers are hilarious 😂 they have no clue WTH they are doing 🤣 😆. Looks like an amusement park but the rides are equipment instead of carnival rides 🤣
I'm shocked the ground isn't pumping. It's been rolled far too much. This must be a testing ground for a local trade school. And today is the "introductory demonstration". Burning all that diesel adn not once pulled any string. Where are the grade stakes or GPS antennae?
What’s so extraordinary skilled about this?
Exactly, ground speed to high and machine was bouncing, wheels were not leaning towards the discharge side, skilled my ass!!!
Just a dirt pusher. Final trim and and a water binder and there cutting to tolerances is a gun operated I should know my old man was one. No Lazer bullshit he needed
*SKILLED!? Are you kidding me!? This is a What Not to do video. Blade speed is Twice what should be (he’s BOUNCING!) , putting the windrow back into the previous cut, making passes on top of passes with NO SIGHNS of ANYONE OR ANYTHING checking grade (WHERE ARE THE GRADE STAKES!?) and the list goes on…*
I'm not a grader operator but I have watched plenty of them over the last 30 years and this guy is rough.
Trying to wear out the dirt?
I’ve run graders 20 years and this is laughable 😂
I just started doing dirt 3 months ago and this is funny😂
@@darea4559I haven't even touched a grader and I know he's fuckin it up
15 seconds into the video I can tell you that this is NOT a skilled operator. At best he is just a "driver". Watch the machine bounce. He is traveling too fast. Improper machine placement, improper circle and moldboard position, no wheel lean. Pushing a large windrow, he should have had some articulation.
Yeah lol this looks like a beginner really, it’s not even on a slope either so no risk in using articulation / wheel lean
الشمري
Only past. . . No good.
Operator still learning. His teacher is in the cab with him.
@@alanlambert-bz4to Then why didn't this "teacher" tell him to slow down? Plus all the other things he was doing that needed attention. Believe me, I know that there are no two operators that do things all the same way, but there are things that ARE standard techniques. Those are all things that his teacher should have been addressing. You could read some of the other comments, and they were saying basically the same as I was. Some were nicer than I was in their critique, some weren't. I mean if your video is going to say "Amazing operating techniques, skilled operator", you should have had the "teacher" operating.
A good blade man never lets tailings roll off the leading edge of his blade…maybe if you are bulking and hitting piles but never when you’re finishing…this guy is doing good for just learning but he’s not an experienced finisher by any means!..these are the things you must go through as you learn…I was there too when I first started!..
The new graders are pretty quiet. I miss the loud roar of the older caterpillars.
A skilled grader operator makes sure the mole board is rolled back all the way, the machine stays intimate with the surface and there’s always material rolling off the end of the blade. This guy is a rookie at best.
For starters its not a mole board
Every bounce of machine is another corrugate .Slow down
Coman réparer les vérins de rotation du nifleuse chonpion
Yeah that is just some dude that learned what lever did what and jumped out there lol and the guys on the rollers are hilarious 😂 they have no clue WTH they are doing 🤣 😆. Looks like an amusement park but the rides are equipment instead of carnival rides 🤣
That's f×cking hilarious 😂 😃
And they have the sheep's foot packing gravel 😅
I love to watch the grader
"Motor Greder"? That says it all about this video.
Кто мне скажет какой грейдер лучше камацу или джундир?
Good job 🙏🙏
Yes I agree not an old school grader man. They don’t go fast but they only go over it once
Conditioning. That's the standard bro
Bhaiya hmm bhi grader operator h fast chalane ko bola jata h.
Sub..Top nhi bn rha h.
Ausgezeichnet 👍👍👍👍👍👍
Good Job. Thank you brother. God bless you 🙏🏽
nice work🎉
I'm shocked the ground isn't pumping. It's been rolled far too much. This must be a testing ground for a local trade school. And today is the "introductory demonstration". Burning all that diesel adn not once pulled any string. Where are the grade stakes or GPS antennae?
Good operator exelent 👍
Try doing that North America
Muito bom mano
fastforward video😊
You can see the instructor in the cab with the driver all through the vidio.
Cc moi je suis un conducteur de niveleuses mais je suis au Burkina Faso
My problem was digging to much but think I got it appreciate the video!
I love thi
Inexperienced contractor 😂
Excavator operator ki vacancy h kya
Buen trabajo
esse emilho não deixa ninguem concluir seus pensamentos , mucha a oreia e fica calado emilho
The bouncing was cool. But hey, you got a army of rollers following
mantap 👍
لك ايرك معلم اه يا نمر
The only “amazing” thing about this is how much that poor grader is bouncing.
Rough operator
Please i need grader to buy
Sangat bermanfaat
Apparently they dont build anything to spec in what ever country this is
म I am a high scale grinder operator
6años bem e você não vai dar clase virtualea me dijo q vaya
6años y no me voy a 9
I call this, roush to do slow work.
José Carlota Oliveira Reis
I don’t know what he’s trying to do, Ive never seen anyone blade like that before
Guys with sakai and hamm behind grader are not skilled,they dont drive their machine properly...
Support
It is good operator very much good hi is skilled operator and cayenn
komatsu 655❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
sad part is he has a trainee riding with him. gonna have 2 non-operators now.
I don't see the skill
ua-cam.com/video/WpgUdCJsHZc/v-deo.html👈
Very well
Work for v ditch
Why the hell is he cutting a ditch like that.... This is laughable at best....😂
My dream grader
CAT lives matter!!!
aingk....no good.
Sorry, but I don't see a skilled operator
nobody riding with me...f that
not even spelt right! As for the workmanship...
Horrible operator.