ZoZo PLL FM Broadcast Driver ( Build ) 87-108Mhz check out radiobuilders.co.uk

I've had this kit for sometime, so at last its done and enjoyed the build.
Was told to expect to see 800mw to a full 1watt output. Was happy with the result.
Will work great with an amp im sure !
The PIC needs to be programmed so will be back with a video to show how that is done.
Thanks for watching don't forget to like and subscribe !!!
Aron102
PCB can be found on e bay

[@djabs446]

Nice one aron. Thanks for taking the time to do these videos 👌🏼❤️👊🏻

[@threeMetreJim]

Looks like a variant of the old Broadcast Warehouse design but using the SAA1057 instead of the MC145170.

[@Aron102]

Dose look similar in some ways 👍 thanks for watching

[@Pasionatdefiare1986]

Nice pll

[@Pasionatdefiare1986]

Beautyfull build

[@radioarchives101]

At last 👍 73 DE Zulu Oscar

[@skunkybillmarleey5652]

Nice ✌🤪👍

[@The-End]

nice job !!! can you share with us please the schematic or the model of variable inductors ?... thank you.

[@Aron102]

Thank you, unfortunately I don’t have a schematic for this, the paper work you see in the video is all the info I have… thanks for watching
Aron
Variable resistor 10K
Variable Capacitor, mini yellow 10-40p
1u5 Choke
Canned Toko MC120 (2t5)
S18 Toko Red (2t5)
S18 Toko Orange (3t5)

[@natebentham]

I bought a couple of these boards but unfortunately they're not available as a kit anymore (from what I've searched).
I'm quite new to building electronics and have a couple of questions:
A) Do I need to use a washer or spacer under 2N4427 transistor or can I just leave a gap between the component and the board?
B) What type of 10K pot is used? I have 3386 but they're square and the one you used is rectangular.
C) What is the difference between the 10u cap (below the SAA1057 chip) and the other ceramic caps? What type of cap is it?
D) Do I need to use 1/2 watt resistors or can I use 1/4 watt?
Many thanks 👊🏻

[@natebentham]

@@Aron102 Much appreciated 🙏🏻

[@RRCbroadcast]

where did you buy this board?

[@Aron102]

I bought it off the guy who designed it..
Send me your e mail address

[@jonhoyles714]

Very nice build can you point me in the direction for some ferrite beads uk
Based seller if possible?

[@Aron102]

www.enigma-shop.com/inductors/ferrites/toroids

[@Aron102]

I have replied but not sure it worked 👍

[@drmagis]

Hi. Great video! How and what did you use to do the PIC16F84 programming?

[@Aron102]

I used the PIC3 programmer

[@antonio1681]

Do you have any suggestions on how to check the output signal of a transmitter to make sure you’re not over modulating?

[@Aron102]

The only way would be to check it is on a oscilloscope.

[@Aron102]

E mail me Antonio

[@jonuejej]

HI its me kisan facebook frnd

[@JBSATE]

Cadê o manual esquematico

[@Aron102]

I don’t have one I’m afraid. The paper work you see in the video is all I have. Thanks for watching 👍 if you have any kits or designs I could build please get in touch. E mail me. [e-mail]

[@Centraldeirrigacao_7927]

where the skema friend congratulation

[@Aron102]

I don’t have the skema I’m afraid 😳. Thanks for watching 👍

[@rdamedialab]

Felicitaciones sera que usted puede hacer llegar a Venezuela para reactivar las radios escolores y comunitarias?

[@Aron102]

English if you can 😎