I have a toshiba tecra z40-A and i have upgraded to a ssd and now i m not able to install windows as it gets stuck at boot loop after the installation of os in ssd …. But if i try to connect my old hdd it works ….. kindly help me
Thank you this has been helpful however I'm not sure on how to get a administrator password, if I could get pass that then my laptop should be working again
If it didn't work, try creating bootable usb and leave it empty. Use it to only help to reboot the device. The other USB entry put the mircrosoft media usb. Then ofcourse follow the steps mentioned in the video.
Sir pa help naman po.. Satellite R50, ayaw mag boot sa SSD. naka ilang reformat na pero ayaw talaga. tapos na ang windows OS installation tapos pagka restart nya, balik sa simula ng windows installation ulit kahit naka SSD na ang 1st boot drive. Pag tinanggal ang Flash drive na pang install ng OS, No boot media ang lalabas. naka dalawang SSD na ako same parin pero pag HDD ang gamitin, same BIOS settings/USB drive pero ok naman. Pag bubukan ang SSD, nandun naman ang windows files nya. Pa tulong naman po sana. thank you
Ok so here is what you do. Reset to default settings. Go back into the boot order and change from csm to uefi if it is a uefi bootable disk. I used Rufus 3.4 and I formatted to fat32 used gpt as my partition scheme and my target system was uefi (non csm) Worked for me. Side note you can get the get error you can use command prompt to use diskpart to change from mbr to get or simply use Rufus and use get instead of more. Hope it helps. I remembered
Deleted if 1. Reformat/delete the drive where OS is installed 2. Opposite partition style either GPT or MBR Solution: make your if your system is gpt then make a bootable gpt. Or if mbr then make mbr. Just click next when in partition selection screen.
Ok so here is what you do. Reset to default settings. Go back into the boot order and change from csm to uefi if it is a uefi bootable disk. I used Rufus 3.4 and I formatted to fat32 used gpt as my partition scheme and my target system was uefi (non csm) Worked for me. Side note you can get the get error you can use command prompt to use diskpart to change from mbr to get or simply use Rufus and use get instead of more. Hope it helps
Ok so here is what you do. Reset to default settings. Go back into the boot order and change from csm to uefi if it is a uefi bootable disk. I used Rufus 3.4 and I formatted to fat32 used gpt as my partition scheme and my target system was uefi (non csm) Worked for me. Side note you can get the get error you can use command prompt to use diskpart to change from mbr to get or simply use Rufus and use get instead of more. Hope it helps
Pahelp po ntry ko n ung una tapos sabi PXE-E61:Media test failure,check cable PXE-MOF: Existing Intel Boot Agent Insert system disk in drive. Ano po next step?
Ok so here is what you do. Reset to default settings. Go back into the boot order and change from csm to uefi if it is a uefi bootable disk. I used Rufus 3.4 and I formatted to fat32 used gpt as my partition scheme and my target system was uefi (non csm) Worked for me. Side note you can get the get error you can use command prompt to use diskpart to change from mbr to get or simply use Rufus and use get instead of more. Hope it helps
Wonderful dear. Very helpful. Thanks 👍
Really helpful, first solution fixed my problem first try!
Thank you for the help!
Nice bro! Works fine, thank u! Hugs from Brazil!
I don't see any of those options
❤❤❤thank you !!!
😍😍😍
Thanks brother, really helped me out !
Awesome work. It worked for me .Thank you
Best of all ❤️❤️❤️ Thank you 👊🏾
This is very helpful thanks a lot 😊😊❤
Thanku❤❤
Thank you so much👌 really helped me
A life saving video☺
Thanks man 🎉❤
No probs man 👍
Third option, RAM is not seated correctly. Take out RAM stick(s) and then place back in same or different slot.
I have a toshiba tecra z40-A and i have upgraded to a ssd and now i m not able to install windows as it gets stuck at boot loop after the installation of os in ssd …. But if i try to connect my old hdd it works ….. kindly help me
Thank you, bro ! Really helpfull.
Thank you! It worked.
Thank you, ITS work 100%
Enjoy
Thanks bro,my laptop is done
Thanks a lot bro ❤
Thank you this has been helpful however I'm not sure on how to get a administrator password, if I could get pass that then my laptop should be working again
What a legend!!
If it didn't work, try creating bootable usb and leave it empty. Use it to only help to reboot the device. The other USB entry put the mircrosoft media usb. Then ofcourse follow the steps mentioned in the video.
Thank you so much 😊
Thank you verry much sir g
Much thank you so much
Hello. When I do this it goes into bios but before that it asks for the administrator password and I don't know what to do?
congratulactions 👨🤝
thanks sir, it work
Thank you worked
Welcome po
secure boot is not shown on my laptop, toshiba dynabook rx3mt
Same here po. No Secure Boot is shown. How to make admin password po?
Thank you.
thank you very much
Thank you ❤❤❤❤❤
I love you
Thank u !
Thank you bro
I couldn't find boot secure I make the supervisor password but it's not avaible and the boot mode Don't avaible to me too what I should do
Thank youuu 😭😭
Thanks man
Thank you
Thanks bro
Thank you so much poooo
Welcome po, don't forget to like and subscribe 😊❤️
Thanks
Sir pa help naman po..
Satellite R50, ayaw mag boot sa SSD. naka ilang reformat na pero ayaw talaga. tapos na ang windows OS installation tapos pagka restart nya, balik sa simula ng windows installation ulit kahit naka SSD na ang 1st boot drive. Pag tinanggal ang Flash drive na pang install ng OS, No boot media ang lalabas. naka dalawang SSD na ako same parin pero pag HDD ang gamitin, same BIOS settings/USB drive pero ok naman. Pag bubukan ang SSD, nandun naman ang windows files nya.
Pa tulong naman po sana. thank you
same problem tayo brad @shan Vym , ayaw din e read ang ssd ko pero my OS na sya after installation. ayaw lang talaga mag boo, baka hindi compatible
Mine said
"Intel R Boot Agent Ge v1
Media test failure
existing intel boot agent
I can't fix it
Same. I bypassed it once to install my own but I can't remember whT I did for the life of me
Ok so here is what you do. Reset to default settings. Go back into the boot order and change from csm to uefi if it is a uefi bootable disk. I used Rufus 3.4 and I formatted to fat32 used gpt as my partition scheme and my target system was uefi (non csm) Worked for me. Side note you can get the get error you can use command prompt to use diskpart to change from mbr to get or simply use Rufus and use get instead of more. Hope it helps. I remembered
Mbr to gpt
will doing this delete existing files inside??
Deleted if
1. Reformat/delete the drive where OS is installed
2. Opposite partition style either GPT or MBR
Solution: make your if your system is gpt then make a bootable gpt. Or if mbr then make mbr. Just click next when in partition selection screen.
thank youuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu
pano po gumawa ng password son sa administrator?
nuff respect to you thank you
working
Que hago si no me aparece lo de Boot mode?
Pudiste arreglar?
Wala po sa akin ang secure boot. Any option po?
Ok so here is what you do. Reset to default settings. Go back into the boot order and change from csm to uefi if it is a uefi bootable disk. I used Rufus 3.4 and I formatted to fat32 used gpt as my partition scheme and my target system was uefi (non csm) Worked for me. Side note you can get the get error you can use command prompt to use diskpart to change from mbr to get or simply use Rufus and use get instead of more. Hope it helps
Boss kailangan ba ng hard disk para mabuksan yung laptop ganyan din KC problema ng laptop ko
Dapt talaga may hardisk boss kasi jan naka install ang operating system
Good day sir, bakit po sakin ayaw ma detect yung caddy
But bro i want to UEFI boot OS not CSM so what can i do
Ok so here is what you do. Reset to default settings. Go back into the boot order and change from csm to uefi if it is a uefi bootable disk. I used Rufus 3.4 and I formatted to fat32 used gpt as my partition scheme and my target system was uefi (non csm) Worked for me. Side note you can get the get error you can use command prompt to use diskpart to change from mbr to get or simply use Rufus and use get instead of more. Hope it helps
Mbr to gpt
how to make administrator password?
Sir pede po patulong..ganyan di po model ng laptop
can you help me?
My laptop can't start up the HDD is missing
Posible bios settings or hdd is defective
hey sir, idk how to make administrator password? can gimme a solution? how and where to make it
I have the same problem 😑 did u get an answer plz
Hi po. No Secure Boot is shown. How to make admin password po? Help po
enter po sa option nang user or supervisor click enter then lagay ka po nang password
@@emmanangelesagustino6746 thank you po
Pwede sa pc?
Pedi rin. Pero double check muna hdd or ssd mo reinsert muna
Pahelp po ntry ko n ung una tapos sabi PXE-E61:Media test failure,check cable
PXE-MOF: Existing Intel Boot Agent
Insert system disk in drive.
Ano po next step?
1st restore factory settings muna sa bios
Same issue, did you solve it?
@@wayneslink can you help me?
same issue, where to find restore factory settings?
Ok so here is what you do. Reset to default settings. Go back into the boot order and change from csm to uefi if it is a uefi bootable disk. I used Rufus 3.4 and I formatted to fat32 used gpt as my partition scheme and my target system was uefi (non csm) Worked for me. Side note you can get the get error you can use command prompt to use diskpart to change from mbr to get or simply use Rufus and use get instead of more. Hope it helps
Pano po pqg bios lock?
Try draining cmos batt, if di gagana check manufacturer bios for unlock
Isnt work
well all of you need to do is disable uefi boot
Me podrías ayudar bro?
@@miguelcano4936 Mano pudiste arreglar?
Fake
Like you
Thank you so much
Thank you
thanks bro
Thanks
Thx bro