What are you guys saying is not even sound like a cat: DON'T MAKE FUN OF THIS GUY HE WORK SO HARD ON DOING THIS DON'T MAKE FUN OF HIM OR ELSE HE WILL PUNISH YOU LIKE FOR REAL
you have all sort of tools like the machine that cuts the pieces out. you have a work shop full of cool stuff 3d printers are cool but material pla has issues with durability and heat.
Brushless dc motors were century ahead technology... And is the future...lowest power consumption vs output delivered... Home appliances are now replacing induction single phase to Dc or Bldc❤.. Loved it
Completely bogus, there’s 3 lines on the disk when it’s running which is why you never show it running to or from stop. This motor wouldn’t actually do anything in practice as the windings are too wide and 2 far from the stator, also with 2 magnets it would have very little torque. It will do about 25k rpm maximum with no load, add load it wouldn’t even move a 1/18 buggy and even then it would melt or just disintegrate after about 30 seconds. Why do you think the likes of TP power use small statist with minimal clearances and Kevlar bound stators. That’s why they are rated to 10 second bursts of 100k. most manufactured motors are only rated to 50-60k and at that speed the stator is still the weak point. Other than that it was a nice little project to show how a brushless motor is constructed. I suppose the make a 75k motor was a little click bait.
i use 4 side magnet like yours, but different size. I use magnet nyodimium 40x10x2 mm and also I use 3d print with pla filament for the body/structure. I put 0,4 mm copper wire to get good speed of motors. do you have a solution for me? because this is first time for me to make electrical motors
what amount of current and voltage are you running through it to get that high of rpm and what do you think the limit of current and voltage you can run through it is?
What can we do with this device ? For example I want to prepare engine for undersea scooter and I need 50 kg pull power... is it work ? There is no information like Amper,Volt or how to calculate ... I wish them
Cool motor! What I like to know where to get that tool that cleaned the wires that shown 12:13-12:25 Please give me a link to buy these tools or what it called so I can buy one
Hi, nice video, can you tell me how to calculate how many copper turns you have to do for each pole, do you have a table? Please answer me, bye and thank you
I'm confused about using copper wire to wrap around the magnets... If it's purpose is to hold the magnets on then carbon fiber would make more sense (that's what Tesla did), so I'm left thinking that it's serving another purpose. I'm guessing the limit on rpm would be the inductance of the coils at these high frequencies. Can anyone explain more?
Brushless cat sound motor 😂 👍
555🤣🤣😂😂😂🤣🤣👍👍👍👍👍
🐱
😂
What are you guys saying is not even sound like a cat: DON'T MAKE FUN OF THIS GUY HE WORK SO HARD ON DOING THIS DON'T MAKE FUN OF HIM OR ELSE HE WILL PUNISH YOU LIKE FOR REAL
You are a sound engineer.
Your family was thinking that you bring a cat in your room😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂
And caller and I came with my
DIY a CAT 😼👍
Diy cat sound making motor
🤣🤣
Yes lol
Wow...this is hell of an RPM man.love it.
wow, 71K rpm, not bad at all. Nice work. 😁👍👍👍👍👍
Wow very nice 👍👍👍
Wow 👍. 6800kv
Excellent work !!! Congratulations !!!
I wish I had access to all the tools aka toys you have. You are blessed.
3d printer
you have all sort of tools like the machine that cuts the pieces out. you have a work shop full of cool stuff 3d printers are cool but material pla has issues with durability and heat.
@@sumdumguy4659 You can use abs, carbon plan or others
70,000 rpm with a 2 pole motor.. crazy
The motor sounds like a angry cat!
GREAT JOB KEEP IT UP MEOW.
Brushless Cat Sound Mawoooooooooo awwoooo 😾😼😿😂😂😂😂😂
Brushless dc motors were century ahead technology... And is the future...lowest power consumption vs output delivered...
Home appliances are now replacing induction single phase to Dc or Bldc❤..
Loved it
Грандиозный проект 👍👍👍👍👍👋👋👋👋👋 Просто ЖЕСТЬ!!!!!
Пиздеж, а не проект.
Very impresive. Good job.
Hi, have you tried how long it lasts at maximum rpm and thrust it can have?
Thanks, good job
i don't think that it will last long , did you notice how he is trying
to give it a boost ?
Great work,you are the best!
Completely bogus, there’s 3 lines on the disk when it’s running which is why you never show it running to or from stop. This motor wouldn’t actually do anything in practice as the windings are too wide and 2 far from the stator, also with 2 magnets it would have very little torque. It will do about 25k rpm maximum with no load, add load it wouldn’t even move a 1/18 buggy and even then it would melt or just disintegrate after about 30 seconds. Why do you think the likes of TP power use small statist with minimal clearances and Kevlar bound stators. That’s why they are rated to 10 second bursts of 100k. most manufactured motors are only rated to 50-60k and at that speed the stator is still the weak point.
Other than that it was a nice little project to show how a brushless motor is constructed. I suppose the make a 75k motor was a little click bait.
8:18 Maybe dump question - this wire that covers the magnets is only to hold them in place when they are spinning ultra fast?
to increase the magnetic flux i think since he used plastic as base
I think this is the fastest electric motor than i saw
The wire around the magnets is to increase flux and at the same time hold the them, right?
Yes
No. They are a secondary winding, shorted together to produce an opposing magnetic field. The motor is a sort of "rotating transformer".
how does your cnc machine work? laser? whats the specs? my bad. saw it in link discription
I've to appreciate for your winding 😵👍
The Beeeeeeest
Can i use the same method for an electric car?
Must the magnets one face north and one south or are both south or both north
It's very dangerous. Magnets can bounce out at any time due to high RPM because of centrifugal force...
Нет, там суперклей, и медная проволока, и даже если отскочат будут внутри мотора, а мотор тоесть эти листы уже не разобьются учитывая их толщину
I imagine that is why he wound and glued the wire around the magnets on the rotor.
mv²/r
Really good work brother
Perfect I like it..good job
i use 4 side magnet like yours, but different size. I use magnet nyodimium 40x10x2 mm and also I use 3d print with pla filament for the body/structure. I put 0,4 mm copper wire to get good speed of motors.
do you have a solution for me? because this is first time for me to make electrical motors
What is your problem? It can't work? Low rotating speed?
I think you would get better results by sandwiching metal plates in-between for the magnetic core.
seems incredible,I don't get how?
Wouldn’t it add more friction, requiring more energy?
Less eddy current-> more flux than heating
@@vishva8kumara worth trying, thank you sir
Of course keep enough clearance so it doesn't scrape. I didn't understand the friction thing earlier.
How much money did it cost you to make it, how much money would you sell it for?
Too Good Bro
But you don’t explain about the wire gauge and how many tum do you roll on it?
10:04 50 turns
Wow amazing exsperimen 👍👍.
This is a great job
what amount of current and voltage are you running through it to get that high of rpm and what do you think the limit of current and voltage you can run through it is?
The rpm is wrong.max rpm is above 10000
can you make 160/150a bldc motor and winding castle bldc motor Style.
Please make soon
U coil over magnets so that it can't move?
What are the volts and amperes consumed by the motor?
Ok I need that electric wire stripper. I didn’t even know it existed.
bhai yea motor Kitna kg carry kar sakta hai
What can we do with this device ? For example I want to prepare engine for undersea scooter and I need 50 kg pull power... is it work ? There is no information like Amper,Volt or how to calculate ... I wish them
I like the maticulousness of your work, but why are there windings around the rotor
Teaches us how to make a ESC 500A. please
You making an e bike or an Rc ? 😅
Just add parallel mosfetss
what is bodi materiel brother
Is there a certain magnet you need if not which magnet do I need.
great video! but too much glue for me
Glass cutting kaisa Kiya ??
Same dinamo starter car, good job
Link me Diya Gaye items bahuth megenge hai janab BLDC motor banane ke paise se readymade khareed sakthe hai ji
Could you do it 10 times bigger and use it on a ev? Most of the ev kids out there uses only 5 kwh nominal
Hey ... can this motor make an ev car run at 75K rpm?
My 18 minutes really worth the masterpiece👍🏻👌💪
But wait I have a question
Why didn't you gave us the laser cutting machines program?🙄
Same question
Can’t we print it with a 3D printer? I think you can try the frame with wood as well.
Does it have any torque at all?
Pls donot add cringe music, else your content is superb, cheers
Why wrapped the magnet with copper wire?
Can you please upload the laser printing files , i want to make this motor to use it in a project .
सर क्या इस मोटर को 160ah बैटरी से चला सकते है
Is this engine powerful as much as " T500 Thruster" ?
That is also a magnet, effectively 😂😎😁
how much does the engine weigh?
Its a motor.
Can I ask about the approximate weight of this motor ??
I want to know the approximate pull force
Wow l love it Bro...☺☺
Dear , a lot of people asked you to upload printing files for the design , can you send it please ??
why the rotor winded copper wire ?
What is function of copper winding on rotor?
Es de adorno para que se vea chido.
Can you upload a version without the dreadful thumping please? I'd like to watch but the thumbs are panic inducing...😮
hi, how do you arrange the magnetic poles? does the N-N? or is it a N-S combination?
and how can you determine the number of turns ?
Yes, it is.
Please make next time small size high speed brushless motor
Rotor copper wires end?
Please make big bldc motor for air cooler lowest amp & high rpm👍👍
Which glu are you using
My guy got a laser cutter but no hammer lmfao
How much does it consume from battery at full speed 70k RPM?
I think it is good to be used in drones
Lol what a mad fellow u r are😂
would it not help at all by having a metal like iron or steel also within the fields?
Если только сердечники для катушек
Cool motor! What I like to know where to get that tool that cleaned the wires that shown 12:13-12:25 Please give me a link to buy these tools or what it called so I can buy one
I think its called a wire stripper
@@lillavacado11 I looked everywhere in website and can not find them. Please give link. I find all kind simple tools but nothing like this video :(
Какой силы применял магнит в килограмах на подъём веса.
The question is how to make that magnet in any form according the size of motor you will make.
Nice 👍 now you can disrupt spacetime
"American Tech".. The background music says you are an impostor😂
Forget acrylic sheet, we need loads of superglue!!!! ❤✌😂
what was that cutting the acrylic at the beginning?
I know this probably a dumb question but does the shape of the magnet affect the speed etc.( I have cylinder magnet and want to know if it will work)
Не будет сильно влиять, ну максимум обороты до 50000 упадут
And that’s how the early police sirens sounded
Excellent
OHH AMIGO QUE EXCELENTE MOTOR GRACIAS...100% RECOMENDADO...
Its seems to have high torque since ur using neodymium.. and 20 ah on 12 v... But since dc frequency is high i doubt that🤔🤔
Hi, nice video, can you tell me how to calculate how many copper turns you have to do for each pole, do you have a table? Please answer me, bye and thank you
50
@@Dark_Knight15 Thanks for the answer, but I wanted to know HOW to calculate the total of the coils, is there a reference table? Thanks
I'm confused about using copper wire to wrap around the magnets... If it's purpose is to hold the magnets on then carbon fiber would make more sense (that's what Tesla did), so I'm left thinking that it's serving another purpose. I'm guessing the limit on rpm would be the inductance of the coils at these high frequencies. Can anyone explain more?
Nice motor!!
Like that noise sounds like a siren and a turbo car and airaid siren
Good
How you calculate the magnet power and the swg of wires ? 👍Keep up.
ohms law
Hi, rotor's wire are connected each other?
good but what about torque ?
How long for every part and what size of the wire please
Nice project
how much current that u used?
Can i use this motor in any thing ?🤔
Hey, ever tried putting metal cores in the stators?
Can you give us the measurements for the acrylic cutouts please!
Put it under load and it'll fall apart.
no entendi para que es la bobina que enrrolla en los imanes, o a que se conecta?