What a nice little tip that is with using the circlip in the lathe chuck to locate the piece for machining. I'm going to have to buy a selection of circlips now!
It is a good tip yes. But it should be enhanced a bit by using a clock indicater and a magnetic base set to hold finger clock and try to set the workpiece more accurate. Otherwise a very good video afterall and im impressed as to whats being achieved there
I've been around lathes, mills and other workshop kit for nearly my whole life and I've never seen that circlip trick before. It's fantastic. I love it. It's so simple. I will definitely use it sometime soon. Regards Mark in the UK
Читаю коментарии и виду что весь акцент направлен на стопорное кольцо. Я думал что я один из не многих кто незнал этот лайфхак. А оказалось таких как я достаточно. Я тоже за все время просмотра ютуба впервые такое увидел. Никто так не делал, хотя наверняка есть такие люди. Сейчас думаю во многих роликах это будет показано так как многие друг у друга набираются опыта. Я тоже обязательно этим воспользуюсь. Спасибо автор.
Nice build. That is basically the exact same idea in most every pneumatic hand rotary tool as well. Except they use vanes from non-metallic materials so they seal better and wear less... When those tools start loosing power, you replace the vanes and you are back in business... Thumbs Up!
Nice build but you need much much higher precision if the pump shall give more pressure than a couple of bar. My powersteering pump is of the same type and when it failed I bought a new one but I took the old one apart of curiosity. I couldn't even see any scratches but it had lost pressure anyway. The wings need to be very tight in the hub and the inside of the housing needs to be ground and polished. The smallest gap or scratch and the pressure is lost.
Everything was fine, only if you had touched the contact surface of the aluminum parts (5 pics) with the inside of the main part, the pumping power would have been much higher. That is, you would level the parts with the inner radius of the cylinder. I hope I got my point across❤
@@metallantik In my VE Rotary Diesel Fuel Pump in 1HZ engine it has those think its 5 veins like that and they just sit in the slots in very tight tolerances and centrifugal force spins them out it doesn't have any springs. The outer edge of each bit has a slight curve and the centre of the inside one has a straight cut grove i assume help to not make suction when they go in out as it spins. Cool lathing work.
Reminds me of the time I invented this very pump design back around ~1985 only to find out a few years later it had already been invented a long time prior and in wide spread use. I find it amazing how the same things can be thought up by many different people over time.
I like the design especially when impeller is so simple but i was thinking with your use of springs, if the impeller was spinning at a high RPM would it still get a good seal as the fins be thrown out towards the side of the case similar to an pneumatic motor.
the second improvement could be that you clamp the milling cutter and the part into the tailstock in the lathe and you can mill, file by hand with quite a lot of effort
Well done But there is another way to get more accuracy when putting those piece in the lathe I blotted some aluminum rod in between the jaws, and when I go to use it without the jaws in place, I machine face it, they are removable, And if he did not have a mill He could have held that center piece on the carriage on the lathe and used a milling bit or even a drill bit to cut a real perfect slots .
Love the fact you flew clean past the tolerances for the vanes, and installed the oil seal backwards. You can always figure out which side is the side that fluid is supposed to be on by the easier of the 2 ways to install a seal on a shaft. Lip always faces higher pressure.. 😂
Incredible, very skilled and talented to make your own rotary vane pump, gives me inspiration to make one. Would be nice if you can make a 2 stage vacuum pump. 10:14 - Is this a mechanical seal? Where can I get one? thanks.
This hydraulic pump will definitely work. It is a well known one, but because of materials used and the lack of surface treatment of the pump house, it is just a matter of time until the hydraulic system will be damaged, because of the small aluminium shavings.
Oh hey thanks for the video. I'm cloning some dry sump stages for my engine build, stumbled across this! Nice to see you having fun fabricating. Thanks for the vid!
You made everything up to the plastic hub/bearing in the end. Just wondering why you did not also make that since you did everything else. I mill would make many of the things you did a bit easier and precise, but good job using the tools you had.
Насосы с таким принципом работы используются в автоматах газводы. Они итальянские, стоят под 300 баксов. Могут делать давление 15 атмосфер. Правда у них полость из пластика и стираются они быстро. Этот навряд ли сможет создать высокое давление
Why does everyone unnecessarily destroy phones? Even tho it's not working it can help someone fix theirs and keep trash from landfills. In modern times people only buy stuff. Repairing is where the real charm is
What a nice little tip that is with using the circlip in the lathe chuck to locate the piece for machining. I'm going to have to buy a selection of circlips now!
😃🙏🙇❤️
Agreed. Love it.
It is a good tip yes. But it should be enhanced a bit by using a clock indicater and a magnetic base set to hold finger clock and try to set the workpiece more accurate. Otherwise a very good video afterall and im impressed as to whats being achieved there
Nifty
I saw him doing that, didn't make sense how it was helping him. Can you elaborate more on the usefulness? Thanks.
I've been around lathes, mills and other workshop kit for nearly my whole life and I've never seen that circlip trick before.
It's fantastic. I love it. It's so simple. I will definitely use it sometime soon.
Regards Mark in the UK
Читаю коментарии и виду что весь акцент направлен на стопорное кольцо. Я думал что я один из не многих кто незнал этот лайфхак. А оказалось таких как я достаточно. Я тоже за все время просмотра ютуба впервые такое увидел. Никто так не делал, хотя наверняка есть такие люди. Сейчас думаю во многих роликах это будет показано так как многие друг у друга набираются опыта. Я тоже обязательно этим воспользуюсь. Спасибо автор.
Excellent and beautiful, you are unique😍😍
The circlip idea was awesome!
Thanks 🙏
Лайфхак с кольцом в патроне, в который упирается деталь, просто зачет 👍
Использовать стопорное кольцо прикольно придумано👍👍👍👍
Thanks 🙏❤️
Use of circlip for positioning of part in lathe, is a amazing idea😮
Thanks a lot 😅🙏
As soon as I saw it I assumed that's what those slots were for and was wondering why I never see them. Then I saw this comment.
Согласен
Автор молодец, спасибо за совет тоже буду пользоваться стопорным колечком для базирования детали в токарном патроне👍
Thanks a lot ❤️🙏
Very nice.
Your pump has no ball bearings, so don't apply radial force to the axis with that chain / gear. Use direct coupling to the motor.
Interesting way to register your work, quick and dirty. I'LL have to try it out.
Nice build. That is basically the exact same idea in most every pneumatic hand rotary tool as well. Except they use vanes from non-metallic materials so they seal better and wear less... When those tools start loosing power, you replace the vanes and you are back in business... Thumbs Up!
В насосы такого типа не ставят пружины под лопатки, они работают за счёт центробежной силы. Меньше трения на лопатки, более свободный ход.
А алюминиевые лопатки долго прослужат в таком режиме?
Nice build but you need much much higher precision if the pump shall give more pressure than a couple of bar. My powersteering pump is of the same type and when it failed I bought a new one but I took the old one apart of curiosity. I couldn't even see any scratches but it had lost pressure anyway. The wings need to be very tight in the hub and the inside of the housing needs to be ground and polished. The smallest gap or scratch and the pressure is lost.
You made an accurate point 👍🙏❤️
Using the circlip was new to me I will have to get a set Thank you
Everything was fine, only if you had touched the contact surface of the aluminum parts (5 pics) with the inside of the main part, the pumping power would have been much higher. That is, you would level the parts with the inner radius of the cylinder. I hope I got my point across❤
Thanks for the tips, I will definitely use your advice ❤️🙏🙇
@@metallantik In my VE Rotary Diesel Fuel Pump in 1HZ engine it has those think its 5 veins like that and they just sit in the slots in very tight tolerances and centrifugal force spins them out it doesn't have any springs. The outer edge of each bit has a slight curve and the centre of the inside one has a straight cut grove i assume help to not make suction when they go in out as it spins. Cool lathing work.
Reminds me of the time I invented this very pump design back around ~1985 only to find out a few years later it had already been invented a long time prior and in wide spread use. I find it amazing how the same things can be thought up by many different people over time.
Exactly, I thought this was my idea, then I realized it was invented before me 😃😃🤦♂️🤷♂️
Makes you wonder how many modern inventions had been utilized by ancient peoples but lost to time
WOAH! This is really cool. Thanks for sharing!
It looks like a pretty good hydraulic pump you're using your time for something really worthwhile
Making something like this is very hard. You are a skilled person ❤
Thanks ❤️🙏
I really hope you sent this to the phone manufacturer. Lol. However, I will be using this to help me design a few things. Thanks, Brother!
بسیار خوب❤❤❤
❤️
I like the design especially when impeller is so simple but i was thinking with your use of springs, if the impeller was spinning at a high RPM would it still get a good seal as the fins be thrown out towards the side of the case similar to an pneumatic motor.
Yes,youd get both the springs and the centrifugal force throwing them out
Chăm chú xem đến cuối cùng lại đi phá hư cái điện thoại, vậy lấy cái búa bụp cái là xong cần chi mất thời gian quá.
Interesting😉
Thanks🙏
I agree i have a selection of snap rings or circlips I’ve never seen that before I’m trying this thanks
what is that piano wire in a coping saw? great build btw.
Adorable little vane pump. Well done.
Hmm... not much holding those vanes in the recesses.
Thanks a lot 🙏
the second improvement could be that you clamp the milling cutter and the part into the tailstock in the lathe and you can mill, file by hand with quite a lot of effort
Thanks you.
I got concept of hydraulic pump 🙏
🙏
Well done
But there is another way to get more accuracy when putting those piece in the lathe
I blotted some aluminum rod in between the jaws, and when I go to use it without the jaws in place, I machine face it, they are removable,
And if he did not have a mill
He could have held that center piece on the carriage on the lathe and used a milling bit or even a drill bit to cut a real perfect slots .
I didn't know that trick to center pieces on a lathe... and I work in a workshop of lathe... thanks for the video.
❤️🙏
Nice skills friend
Thanks ❤️🙏
Love the fact you flew clean past the tolerances for the vanes, and installed the oil seal backwards. You can always figure out which side is the side that fluid is supposed to be on by the easier of the 2 ways to install a seal on a shaft. Lip always faces higher pressure.. 😂
Great content! Keep going
Excellent pump.
Incredible, very skilled and talented to make your own rotary vane pump, gives me inspiration to make one. Would be nice if you can make a 2 stage vacuum pump. 10:14 - Is this a mechanical seal? Where can I get one? thanks.
The test subject was a tough one.😅😅😅
Nice build.
Creative video, thanks :)
❤️🙏
Hello, I really liked your video, what is the name of that type of anti-gas bearings?
Idea Is awesome.
But, ek hydrolic pressure banane ke liye 20 hazar mobile kon tut ta ?
Thanks ❤️
have you messured the pressure the pump is able to generate?
Awesome 👍
Thanks 🙏
You have great ideas. Thanks
a smart and professional job👏😍
Thanks a lot Ali ❤️
This hydraulic pump will definitely work. It is a well known one, but because of materials used and the lack of surface treatment of the pump house, it is just a matter of time until the hydraulic system will be damaged, because of the small aluminium shavings.
Absolutely correct, thanks a lot ❤️🙏
Молодчина! Руки с правильного места растут и голова работает!
Thanks a lot ❤️🙏
@@metallantik Вам спасибо, за то что делитесь своими навыками!
For an vacuum pump (desoldering tool) I've seen a similar design but using graphite (carbon) vanes.
amazing 😍👌
🙏thanks
Convert your lathe to a horizontal mill for your slots..
Very informative thank you ❤❤❤
Nice 👍🏻
what determined where the inlet and outlet go as i would have thoungt the most open portion of the pump and the most closed
Hola donde puedo encontrar planos de la bomba hidráulica
Oh hey thanks for the video. I'm cloning some dry sump stages for my engine build, stumbled across this! Nice to see you having fun fabricating. Thanks for the vid!
May want to consider using an old power steering pump. Cheap & long life hydraulic pump.
you're welcome ❤️
You are very smart and skilled 😍
Thanks 🤩
Impresionante es una bomba de verdad se puede subir agua a un tanque con un diseno mas grande gracias Argent
Awesome. You should definetly buy a mini mill.
Thanks a lot 🙏
Чувак с лобзиком ты здорово придумал 😅
Now you need to make a couple drive motors so you can make your own lawnmower.
Fun project, nicely done
Thank u so much 🙏❤️
What's your top pressure?
It was interesting❤❤
❤️🙏
Very good
cant you just drill a hole in the center, then drill an offset hole in the rotor?
Gut gemacht 👌
Danke schön 🙏
You made everything up to the plastic hub/bearing in the end. Just wondering why you did not also make that since you did everything else. I mill would make many of the things you did a bit easier and precise, but good job using the tools you had.
Thanks a lot bro 👍🙏
Très bonne idée d utiliser le cervlips merci pour ton idée
🙏❤️
świetnie to wykonałeś moje gratulacje 👍👍👍
you're welcome 🙏❤️
Super pompa , ingenioasă fabricarea ei, dar pâcat de telefon.
Thanks a lot
😅
it looks like you put the shaft seal in backward at the end, the side with the little spring is supposed to face the pressure.
👍❤️
sehr schon perfect vielen dank fur tecknik du gut machen arbaiten dugute
🙏
Күшті насос екен уйге қажет май құйған ға
Das gefällt mir super 😍
❤️🙏🤩
Could you provide a print for the pump
Дуже круто,єдине що незрозуміло- навіщо телефон зламав?
Phót bơm thủy lực..mua rẻ ơi là rẻ.. tự làm ra mỗi cái.. tính theo giờ.. có thể mua năm mười cái..xịn .. bền tốt..hi...hi...
Перекачивать воду из емкости в емкость пойет, но не для создания высокого давления.
I would love to do that to my cel as well!lol
🙏❤️
Das schon berawo❤❤❤❤❤
Thanks 🙏
Насосы с таким принципом работы используются в автоматах газводы. Они итальянские, стоят под 300 баксов. Могут делать давление 15 атмосфер. Правда у них полость из пластика и стираются они быстро. Этот навряд ли сможет создать высокое давление
Nice work but I don´t recommend to wear gloves of any kind.
Can I have the work plan please
Where is the bearings???😊😊😊
Does not need 🙂
Not much good for hydraulic pump but would make excellent suds pump for lathe coolent!.
👌❤️🙏
How much the is
Só pelo anel elástico como stop já valeu 1000 like
So freaking cool men
Very nice 😂
Thanks bro 😁
Теперь я знаю как разобрать мобильный телефон))
Nice 👍🎉😂 یه چه مسخره بازیه فندکمه بیار 😂😂😂😅
Akbaaar slow 🤣🤣🤣
Top
🙏
Probably cheaper to buy a pump rather then buying a lathe, mill and all the rest to make to pump... :D :D
what that phone ever do to you?
🙁
❤ sao mà hay quá dị.
Genial...
Насчёт стопорного кольца это хорошая идея, а вот зачем смартфон ломать... непонятно.
🙁
Please bulid hydraulick motor
Why does everyone unnecessarily destroy phones? Even tho it's not working it can help someone fix theirs and keep trash from landfills. In modern times people only buy stuff. Repairing is where the real charm is
🤷♂️❤️🙏
Зачем вручную нарезать пазы в латунном роторе имея токарный станок??
👌👌👌👌👌👌
Erakh beni sim miam moremesh 😁