Good evening brother no fuse never blows up. because the startup resistor is very high value resistor. it provides very low current (it is noramlly in milliamperes) if zener diode gets short circuited, it will not allow to build voltage on VCC capacitor if Bias diode or vcc capacitor is damaged, it will never be a cause of fuse burning
Thank you for the reply 🌹, so on most cases the fuse will blow up if there is a short in bridge or before bridge? I see it alot in videos you make. Thx
Hie sir I am Aaron, and one of your followers of your Channel. Thanks you for sharing this information we're learning well. Please may you teach us how to read schematics of audio amplifier especially where multiple detached diagrams are involved. Best regards
Any schematic is the same to read. It is simply parts joined by wires and nothing more. Look at the parts and check datasheet to see what it does then follow wires to see how it is connected. That is all you can get from a schematic at basic level of understanding. To know how the device works you need a deep level of electronics knowledge that can not be given in a short video. To learn, get devices and find schematics for it then follow the schematic and at the same time check the device circuit board. To troubleshoot any device start at the power input. For amplifiers, they can get very complicated and most of the time for those they are nearly impossible to fix. For more simpler amps, if power is present but no output there are many things to check and this is where the schematic comes in use. Find output on schematic and trace backwards, often to op-amps or power amp chips, connected capacitors, resistors, diodes, transistors, mosfets etc. Watch more videos and read books about electronics, then watch and read more. If that bores you then repairing is not for you, toss item in bin and buy a new one ;-)
Question? Where Or How Are Locating The Schematics To The Power Supplies: What Are Your Sources For Obtaining Source Schematics To The Power Supplies . This Is My One Biggest Problem To Repairing These Types Of Electronic Devices..... THANKS For Your HELP
Obtaining a schematic diagram of a specific power supply of any brand is probably not always possible. Alternatively you can find a similar schematic diagram from the typical application circuit diagram from the particular switching ic datasheet which is being used. Otherwise you'll have to trace and reverse engineer the power supply you have.
Just search model of psu or board numbers printed on pcb. If nothing is found then not available. Especially for newer items there are never any schematics. This is why you should always keep older electronic items and repair them if possible because new items are made in a way (on purpose) so that they are more difficult or impossible to fix.
Good morning from Spain, is there any way or way to know the voltage of an SMD capacitor once it is off the board? Thank you and greetings, (I don't speak English, I will read the translation of the video)
The most common way is to inject voltage using a bench psu with current limiting. Do that responsibly after you educate yourself how to correctly do it. Watch Sorin at Electronic Repair School for more info.
Google search the 3842 ic or other swps ic such as tl494 and you will get "sample" smps circuits. This is what Haseeb typically uses when none are available. OR take a "screen shot" during the video.
Thank very much Prof, in 10:35 cap+ diode+ zener if shorted, it should blow up the fuse? Much appreciated 🌹.
Good evening brother
no fuse never blows up. because the startup resistor is very high value resistor. it provides very low current (it is noramlly in milliamperes)
if zener diode gets short circuited, it will not allow to build voltage on VCC capacitor
if Bias diode or vcc capacitor is damaged, it will never be a cause of fuse burning
Thank you for the reply 🌹, so on most cases the fuse will blow up if there is a short in bridge or before bridge? I see it alot in videos you make. Thx
Probably the best video about its topic ever!
ohhh..sir ..one more time this is amazing information you re giving me ..thank you very much..god bless you..im from brazil..
You are most welcome
Enjoy this video, very informative ❤❤❤❤❤
Very very informative and knowledgeable vedeo. Very helpful in halping smps circuit. Thank you so much God bless you.
Thank You Engr, thank you once again
Always welcome
Thank you so much sir your words your kindness.from my side.i will try to help as I can to support your channel sir
Very Good video 🎉🎉
Very good and useful information sir thanks for sharing this knowledge to us
Gracias por su excelente colaboración. Saludos desde Argentina.
An amazing useful lesson. Thanks a lot
Selamun aleykum brother İts a perfectly video thank you so much
Thanks and welcome
you re the best teacher without shadow of doubt..
thanks a lot for your valuable words
Thank you very much for sharing your knowledge with us Sir. But I want to where you get the circuit diagrams.
Thank you so much sir 👍
Most welcome
Good Job, congratulations. Spain
Shukriya Maestro
good morning and have a nice day
thank you , very match
Hie sir I am Aaron, and one of your followers of your Channel. Thanks you for sharing this information we're learning well. Please may you teach us how to read schematics of audio amplifier especially where multiple detached diagrams are involved. Best regards
Any schematic is the same to read. It is simply parts joined by wires and nothing more. Look at the parts and check datasheet to see what it does then follow wires to see how it is connected. That is all you can get from a schematic at basic level of understanding. To know how the device works you need a deep level of electronics knowledge that can not be given in a short video. To learn, get devices and find schematics for it then follow the schematic and at the same time check the device circuit board. To troubleshoot any device start at the power input. For amplifiers, they can get very complicated and most of the time for those they are nearly impossible to fix. For more simpler amps, if power is present but no output there are many things to check and this is where the schematic comes in use. Find output on schematic and trace backwards, often to op-amps or power amp chips, connected capacitors, resistors, diodes, transistors, mosfets etc. Watch more videos and read books about electronics, then watch and read more. If that bores you then repairing is not for you, toss item in bin and buy a new one ;-)
thank u my teacher
Excellent thanks for sharing this informative video keep sharing❤❤
Thank you for sharing
Thank u
Perfect i
Make a episode on repairing CCTV camera also sir...tnx
thanks very much sir...
Thanks sir for everything 🙏
Aleykümselam ve rahmetullahi ve berekatuhu. ❤❤🙏
Thank you sir ❤
Most welcome
👍
Pl include PFC section also
Good
Question? Where Or How Are Locating The Schematics To The Power Supplies:
What Are Your Sources For Obtaining Source Schematics To The Power
Supplies . This Is My One Biggest Problem To Repairing These Types Of
Electronic Devices..... THANKS For Your HELP
Obtaining a schematic diagram of a specific power supply of any brand is probably not always possible. Alternatively you can find a similar schematic diagram from the typical application circuit diagram from the particular switching ic datasheet which is being used. Otherwise you'll have to trace and reverse engineer the power supply you have.
Just search model of psu or board numbers printed on pcb. If nothing is found then not available. Especially for newer items there are never any schematics. This is why you should always keep older electronic items and repair them if possible because new items are made in a way (on purpose) so that they are more difficult or impossible to fix.
Good morning from Spain, is there any way or way to know the voltage of an SMD capacitor once it is off the board? Thank you and greetings, (I don't speak English, I will read the translation of the video)
👍👍👌👌
Plz sir, how to detect and trouble shoot ashort circuit in any shorted PCB by power supply. thanks 🙏
The most common way is to inject voltage using a bench psu with current limiting. Do that responsibly after you educate yourself how to correctly do it. Watch Sorin at Electronic Repair School for more info.
@@g4z-kb7ct many thanks 🙏
please share the schematic used here
Google search the 3842 ic or other swps ic such as tl494 and you will get "sample" smps circuits. This is what Haseeb typically uses when none are available. OR take a "screen shot" during the video.
Aap ka WhatsApp no dijiye, canon photo copier machine ka power supply ka problem vejunga
my whatsapp number is 00962-79-5608616
gmail id ashraf4ta4@gmail.com
👍👌👍👌👍👌😢😮😅