Це відео не доступне.
Перепрошуємо.
honda cbr 1000 fireblade front fork oil seal replacement removal
Вставка
- Опубліковано 13 гру 2014
- honda cbr 1000rr fireblade 2008 front fork oil seal repair
all you need is some diy tools and a good frient to help you
the size of the bolt that i screwed into the dampening rod was M8 8mm
After watching a few vids about making a home made spring compressing tool, yours is way the simplest and to the point. It’s worth watching just for that.
Everyone will have opinion on some of the strip / build you have filmed but hey....you did a good job
Props. This is an excellent video. My only complaint is the fluid level was a bit of a worry as I bought a kit with 1 litre (1036ml indicated) But, 93mm from the top works a treat and is less than 500ml. If I might add a suggestion- electrical tape wound around the stanchion makes for an excellent, no damage seal driver with less risk of screwdriver damage. Many thanks!
quick tip: if the damper rod keeps "falling" into the fork leg before you can get the top cap screwed on to it, tie a piece of dental floss or thin string to the rod... and you'll be able to pull it up through the spring/spacer.... cheers
awesome video! wouldn't of been able to do my forks without it
+hundo1000 very much appreciated good sir : ) that was the reason i made it if i could only spare one person from all the research i did. surprisingly allot of people find my hands helpful
omg, this is so much more difficult/more steps than I thought. now I know why it is so expensive to do this in a shop
O melhor vídeo explicando como.desmonta a suspa da cbr. Parabéns
Very informative, but you're missing a very important factor. The amount of oil you pour in is not really a factor. It's the oil height that is crucial, It should be 93mm from the top with the spring out and the fork fully compressed, (2008-2010 model 1000rr) That is very important and crucial to your fork working properly.
its just about how you said it if you use the amount i mention in the video.
you can just pop the top cap and take the lower bolt off and pulled the cartridge I have done it there is nothing restricting the cartridge once the lower bolt is and screwed it slides right out then you can disassemble the shock normally saves a lot of time
+Toby Nuanes i am sure it works that way but the friend i was helping wanted the old oil cleaned as much as possible hes a freak with his bike.
+Toby Nuanes Good info. How much oil do you need to add back though? Also, did skipping the bleeding step cause any issue to you? Thanks.
13:45 :)
didn't skip the bleeding. no reason to skip the bleeding .. its fun! skipping it would mean you leaving old oil in the cartridge where its needed most and you can't pout the exact amount of new oil cause you don't know exactly how much is in the cartridge and if the cartridge is empty you cannot fit all the oil quantity in the tube. what i am showing on 14:14 could be skipped if for some reason you managed to fit all the oil quantity in the tube but you gonna have to do it after, the hard way (jumping up and down on your bike) not fun.. :)
I added 1 16 ounce bottle of 10 weight suspension oil to each shock and by working the innards of the shock and turning it upside down and wiping it with a rag and spraying it off with WD-40 it was very clean no issues did this to my bike about a year ago no leaks:-)
Music has me head bobbing lol good video
When he undid the bottom nut of the fork he could have just taken out the caliper brackets and slide out the seals and redo em from that end...
Thanks a million for posting this vid. Now I will try doing it myself.
let us know how it went :)
well?
I suppose the reason you strip it completely is to get the oil level right when assembling? I'd prefer to keep the cartridge intact but I think for accuracy you need to strip the innards, this vid saved me £130 so good work bud.
A lot of times people will replace the bushing(s) inside because if a leak is left long enough they are allowed to run more dry than normal and will rub off their coating. It's kind of like replacing a water pump on some cars when you also do the timing belt. It's easier to get to while you are in there and the part itself is pretty cheap so why risk you having to take everything a part again later?
Thanks For the video..
excellent video , nice job guys !
Hi Simon Loko. In the service manual, it shows that in order to remove the lower bolt, you need to have a special tool called "fork damper holder" (so that the damper will be hold in place when you unscrew the lower bolt). In your video you don't use such a tool. I do not understand whether this tool is necessary. What do you think?
Hi, anyone have dimension of the upper and lower feflon coated fork bushings? can anyone confirm that it's OD 47mm x ID 43mm x height 15mm & OD 43mm x ID 41mm x height 20mm?
oi, quick question... how did you re-compress the spring to get the shim under the dowel nut with out the center rod falling too low to grab??
Tyler Kilbane I have this same issue. Did you ever get a response?
Do you known the distance of the holes from the white cap? So i can make the home made tool at my own. Thank you
I would consider myself a beginner for motorcycle maintenance/repairs. How difficult is it to replace a front fork seal?
Hey my friend, I have a technical question, I have a 2004 1000RR and my left fork seal was leaking real bad and one day I noticed after riding that the bottom part or lower part if the left fork came out of the piece that is bolted to the wheel and same part that the caliper is bolted to? The fork itself looks to have threads or ridges on the bottom end. I wonder if the oil leaking fork oil caused it to slip out? I was able to hit the front brakes hard at 10mph and it popped back in. What's your knowledge of this? Thank you..
Hi, great video. Just about to change seals and oil on my 929 forks. What was the width of the slot in the metal plate you placed between the plastic sleeve and the lock nuts? Cheers. Paul
Hi buens afternoons, change the seals of the barrales and my bars sound when I pass bache, that cres
How much did all of it cost you to do? I would say mine needs them pretty damn bad i have oil leaking onto my front breaks on my Repsol.
Cory Albertson about 40$
On the spring compression tool you made what was the size of the bolt that you screwed into the dampening rod ? thanks! great vid
+jregz25 M8 the outside of the thread is 8mm.get the one with the finer threads. thanks for you kind words.
+simon loko Im sorry whats M8? and just to be clear its a 8mm bolt with fine thread?
Thanks!
+jregz25 i went to my garage and found the tool i took the caliper and measured
the thickness it reads out 8 mm. the ones i used was 1 with fine thread
and one not the one with the fine thread went through the hole easily
the other one was snug you can use something else maybe if you find a
bolt that has no threads on the tip would be perfect as long the outer
diameter of the bolt is no more than 8 mm it will go in. sry for my
grammar.
Jrega4 M8 = “mate”
Is that any chance to explain about the oil weight? I am kind of confused. I am 147 pounds and I don’t know what oil to use and if it’s change the quantity of oil in the fork.
boa,tarde,tenho cbr2006/2007 quanto ml vai de oleo em cada bengala da mu
inha moto uns fala 466 da bengala do ano 2006/2007,outro falam 517 cada bengala ml,mas 517ml é do ano 2008, qual é o serto meu,amigo
Thanks
good vid bro, thanks for sharing
thank you!
Nelson Grande
Any reason why my fork seal has popped again when it's just been replaced?
Probably due to the fact u may have used after market seals. I would advise using only genuine ones or you'll be replacing them time and time again.
did you fully compress the adjuster so the holes show.. mine are under the top cap.,. .seconds.. you like smoking weed during maintainance :)
Had to give the bottom bush so persuasion the seal was tight too, didn't go in like in the vid.
from spain thanks
:)
their are those that shouldn't work on they're own bikes and then their is you... that was the most barbaric way i have ever seen in changing seals...
there, their, and they're. google it.
@@thepie8u you really made me laugh at your response hahaha.good one
The rest is not very easy...
nice music !!
I never saw the fork seal driver
I have Honda CBR 1000 F , but Im wondering how many ml of Oil ,should I put in the fireblade front fork. Is it the the same amount you put in your honda cbr 1000rr ?
i really don't know i did allot of search to be sure for this one..:/
517ml each
517 ml 10 w oil fork
where can i find the music? thanks
ua-cam.com/video/p-GBTdCYMWU/v-deo.html
music?
ZHU - Faded
They will leak very soon you did it wrong
No grease on the fork seal!! what the fakk
Wraios
Non fai vedere come metti paraolio 😅😅 pessimo video