Dude you are a lifesaver, there's always the chance you can never find specifically what you're looking for, but thankfully you were able to help so many people
THIS IS THE BEST VIDEO OF ALL THE VIDEOS SHOWING HOW TO INSTALL KICK STARTERS ON SCOOTERS, AND TO PUT SPRING ON ALL YOU NEED IS JUST YOUR HANDS,AND A PAIR OF SNAP RING PLIERS VERY GOOD VIDEO I GIVE IT A 10+
thank you very much I struggled with this for a few weeks now and I did not know at all how to put it back even by searching everywhere on the Internet and oily to you I succeeded, finally! 😁
Finally somebody with a brain in their head without 20 minutes of nonsense. I did not see the retainer clip on the shaft… Was trying to get this apart, you save me from beating the shaft to death. Thanks again man
THANKS FOR SHARING. I USE VMC CHINESE SCOOTER PARTS ONLINE. I HAVEN'T HAD A PROBLEM WITH THEM. BE CAREFUL RIDING A SCOOTER OUT THERE ON THE ROADS. DRIVERS WILL TRY AND RUN YOU OVER. CARS, PEOPLE, AND CELLPHONES DON'T MIX!!!🇺🇲✌️👍
Hele mooier video het enigste wat je echt moet doen is het kickrondsel dat puntje wat in het carter gaat goed dik invetten met lager vet en ook onder het halvemaan dat is voor dat alles mooi goed terug schiet en voor slijtage natuurlijk altijd doen en om de zoveel km even opnieuw reinigen en opnieuw smeren dat is om verstopping en vastlopen van de kick te verkomen en t netjes gesmeerd te houden zodat je onderweg niet voor verassingen komt te staan
Since he Did Not say it... I will. It Is Very important that you push down on the half gear Before you drop the small pinion gear into place. There is a weld bead at the third tooth. You MUST make sure the pinion gear is Past the weld when it droops into place!! Otherwise the kickstart will bind and not go down. Bikky No Startyy.!!!!!!! Good Luck
I’m trying to change my drive belt on a Taotao Thunder and cant remove the front of the drive belt casing where the kick start pokes out so I can change the belt.I took all the bolts out but can’t slide it off.Do I have to disassemble the work that you just showed to get it off?
just add some grease/lubricant before you put it together, otherwise the spring wont retract the half sprocket and the kick lever will remain in the down position
Wow glad for the video.first watched some of your vids about 5yrs ago your a very content sounding guy.I would like to know where you got the half gearbox rather then the hole one that would go over clutch on back tire.your response would be greatly appreciated.an as well informative helping me in my search And it would help to know your out there and pushing on. Thanks again for your help.
I have a question! I took the crankcover off to replace the kickstart on a geely 50cc... I have it put back together but it won’t grab the other gear to start the moped. I took it all back off all looks fine but it wont grab. Any thoughts?
Thank you for doing what the manufacturers of chinese mo-taurs wont do. Specifications are exact measurements... Available to everyone except overseas consumers. Yeah, I been to the taotao website, "Not available to IP addresses in MY region??? That's why Japan is Asia's Canada, and China will remain Asia's biggest armpit... Hope that pisses a few Red's off... Just remember, yall started it, restricting OEM specs for Americans...
The camera man super sucks in this video. He is doing a great job by not talking like most guys and just doing it. But only if you can see what he's doing
My w is better . install the spring into cover , engage spring to large gear ,flip cover over install spacer and clip, flip cover over ,grab end of spring with needle nose pliers , attach to tall boss where its supposed to be, install ratchet twasher , install ratchett .
Dude you are a lifesaver, there's always the chance you can never find specifically what you're looking for, but thankfully you were able to help so many people
THIS IS THE BEST VIDEO OF ALL THE VIDEOS SHOWING HOW TO INSTALL KICK STARTERS ON SCOOTERS, AND TO PUT SPRING ON ALL YOU NEED IS JUST YOUR HANDS,AND A PAIR OF SNAP RING PLIERS VERY GOOD VIDEO I GIVE IT A 10+
thank you very much I struggled with this for a few weeks now and I did not know at all how to put it back even by searching everywhere on the Internet and oily to you I succeeded, finally! 😁
Finally somebody with a brain in their head without 20 minutes of nonsense. I did not see the retainer clip on the shaft… Was trying to get this apart, you save me from beating the shaft to death. Thanks again man
I love your video.Action speaks Louder than words.Soe others,theywanted to get some views.They talk more rather than show you what fix.thanks brother
Dude, you're a fucking legend. You could suffer to add captions or naration, but your video helped me when every other kickstarter vid wasn't. Thanks!
Excellent video direct to the point not to much talk 10+
Bro, you just relieved a massive headache. Thanks
thanks , I'm bringing mine in from the cold this winter to fix this exact problem , if there were a way to thank you in silence I would . great video.
@Anthony Callahan yes all the time- lol
😊
😊
THANKS FOR SHARING. I USE VMC CHINESE SCOOTER PARTS ONLINE. I HAVEN'T HAD A PROBLEM WITH THEM. BE CAREFUL RIDING A SCOOTER OUT THERE ON THE ROADS. DRIVERS WILL TRY AND RUN YOU OVER. CARS, PEOPLE, AND CELLPHONES DON'T MIX!!!🇺🇲✌️👍
Thank you so much. I'm working on one I didn't take apart and it was kind of mysterious until now. :)
Hele mooier video het enigste wat je echt moet doen is het kickrondsel dat puntje wat in het carter gaat goed dik invetten met lager vet en ook onder het halvemaan dat is voor dat alles mooi goed terug schiet en voor slijtage natuurlijk altijd doen en om de zoveel km even opnieuw reinigen en opnieuw smeren dat is om verstopping en vastlopen van de kick te verkomen en t netjes gesmeerd te houden zodat je onderweg niet voor verassingen komt te staan
Great video had me sold at the strap idea brilliant.
They make it look so easy, MEANWHILE MY FREAKING SPRING KEPT POPPING OFF EVERY FREAKING TIME I TRY TO HAMMER IT IN!!!😡
bro wtf i just made it my in 3 mins with my fingers only....
Since he Did Not say it... I will. It Is Very important that you push down on the half gear Before you drop the small pinion gear into place. There is a weld bead at the third tooth. You MUST make sure the pinion gear is Past the weld when it droops into place!!
Otherwise the kickstart will bind and not go down. Bikky No Startyy.!!!!!!!
Good Luck
I’m trying to change my drive belt on a Taotao Thunder and cant remove the front of the drive belt casing where the kick start pokes out so I can change the belt.I took all the bolts out but can’t slide it off.Do I have to disassemble the work that you just showed to get it off?
wow, your way is so much easier that using vice grips to hold other end of spring.
now i know...thanks..
/bklyn 👑
Muy buen programa gracias me fue útil 😮
just add some grease/lubricant before you put it together, otherwise the spring wont retract the half sprocket and the kick lever will remain in the down position
How do i keep the big spring in place when turning the gear
what did you use for the starter bendix bushing in the case? i see that it is missing in the video.
I heard it in his hand he's good
Is there something that holds that 3rd piece in when i move kick start it moves up i dont have scooter here so cant look all i have is the casing
Well that said a lot! nice video.
Wow glad for the video.first watched some of your vids about 5yrs ago your a very content sounding guy.I would like to know where you got the half gearbox rather then the hole one that would go over clutch on back tire.your response would be greatly appreciated.an as well informative helping me in my search And it would help to know your out there and pushing on.
Thanks again for your help.
I have a question! I took the crankcover off to replace the kickstart on a geely 50cc... I have it put back together but it won’t grab the other gear to start the moped. I took it all back off all looks fine but it wont grab. Any thoughts?
Look at the comment right above you.Bob Duvall..Did you do what he is saying?
@@soulvaccination8679 sounds like the gear is stripped.
Ive been really strougling to get the spring to not fold in between the gear and the case anybody have any solutions or tips?
guy filming was in the light at some placements but I got it
thanks
Is it the same as ASA 50qt-9 model (kina scooter) as well? =)
Very helpful thank you
how to take it apart?
+Taran Holt you do this video in reverse
@@samili1221 I. Trying to do the same think so I can get at the drive belt
cnniz fakenewz you don’t need to do this to get to the drive belt
You skipping the kick start arm and what size bolt holds it on really screws me and without that information. I am stuck and can't go forward!
If you haven't solved it already, I believe it's a size 8 or 9mm bolt. Just about the same size as the bolts that hold the kickstart casing.
Thank you for doing what the manufacturers of chinese mo-taurs wont do. Specifications are exact measurements... Available to everyone except overseas consumers. Yeah, I been to the taotao website, "Not available to IP addresses in MY region??? That's why Japan is Asia's Canada, and China will remain Asia's biggest armpit... Hope that pisses a few Red's off... Just remember, yall started it, restricting OEM specs for Americans...
☝🏻☝🏻👇🏻👇🏻☝🏻☝🏻☝🏻☝🏻👇🏻
The camera man super sucks in this video. He is doing a great job by not talking like most guys and just doing it. But only if you can see what he's doing
Filming vertically should be a crime...
My w is better . install the spring into cover , engage spring to large gear ,flip cover over install spacer and clip, flip cover over ,grab end of spring with needle nose pliers , attach to tall boss where its supposed to be, install ratchet twasher , install ratchett .
Thank You
merci bien
super videos merci
thank you, enter your name here.
If this works I will subscribe ad I will comment if it worked. I have a vip future champion Chinese scooter.
Katapillar How did it workout for you?
Not that hard if you have a clamp and just hold it
Tp
Tp