Bmw E30 k24 swapped turbo
Вставка
- Опубліковано 22 сер 2024
- This is my k24A turbo project. Motor is off of a ‘06 TSX. Parts that I used to complete my project are listed below. Hopefully I didn’t miss anything.
Car is not a 100% tuned yet, but it will be on a Dyno tune soon and I will update some more videos after.
www.tf-works.com
kpower.industries
-50degree cam gear
-NGK coil packs
-water pump-US housing
-radium fuel rail
-radium fuel regulator
-radium damper
-turbo Intercooler
-oil cooler
-K-Tuned Swivel Neck Thermostat
-new starter
-new alternator
-stock 318i (M42)throttle cable
-E46 clutch OEM
-Acuity TPS
-Hondata map sensor
-K20 oil pump/winage tray
-4 cylinder coding plug from M42
-9000RPM Tachometer
-stock getrag 260 transmission
-Mishimoto catch can
-Greddy boost controller
-kpower industries swap kit
-kpower upper coolant neck
-kpower complete engine harness
-kpower transmission adapter
-Kpower intake manifold
-kpower 74mm throttle body
-kpower aluminum flywheel /release bearing
-kpower Flywheel dust shield
-kpower ECU hondata
-kpower SWAP IDLER PULLEY
-kpower heater port
-TF works clutch fluid reservoir kit
-TF works turbo manifold
-TF works motor mounts
-TF works ID1050x injectors
-TF works oil pan/ pickup tube
-TF works Tail Q blow off valve (Spring yellow )
-TF works Precision Wastegate 46mm (6PSI)
-TF works GREDDY OIL FILTER RELOCATION
-TF works TRACTUFF OIL BLOCK ADAPTER
-Precision turbo 6266
video made by PNW-E30 k24 turbo
#e30 #e30lifestyle #kpower #bmw #bmwlove #bimmer #e30world #classicbmw #bmwclub #bmwlovers #e30lifestyle #bimmerlife #kswap #k24a
Very clean build man! I have a very similar vision for my setup but I’m still working on it. You did a great job!
Thanks bro🙂🙏🏼
Killer video my man!
Thank you!
Perfection, lovely garage 👌🏼
Thank you I appreciate it
I'm currently doing the same engine swap into my e30 but for now I'm keeping it na.
Nice!
Super clean build man. I’m doing the same swap in my 318is, but will keep it NA likely. What trans and diff are you running?
Hey! Thanks I appreciate it. For the transmission, I used my stock getrag 260 and stock diff. NA still gives good power. I Dyno tuned at 205hp with 2.5 down pipe exhaust. That’s my downfall. I should’ve gone with 3 instead of the 2.5. I will upload my old NA Dyno tune video later on. Have fun with your build! You will love it.
Did you delete the abs ?
Yes I did
Perfect swap 👌🏽 have you got more content on IG? Just needs euro bumpers then you’re done
Thanks! No content yet. I’m still working on it. yes euro bumpers will look sick for sure 🙂
VERY NICE !!! what turbo kit did u get and how is the clearance?
Thank you! I have the Precision 4266 Turbo with the Precision Wastegate 46mm and
TF-Works manifold. With this setup, I can say the clearance is not too bad.
Bro love your setup. Clean. Can i ask what oil filter telockit did you use. I need to do the same thing.
Thanks bro. I got a tractuff oil block and the Greddy oil relocation from the tfworks. Easy setup, nice and clean. For the oil filter, I used (K&N hp1002 ). Here are the links for those 2 parts,
www.tf-works.com/tractuff-remote-oil-block-adapter-with-10an-fittings-k20-k24/
www.tf-works.com/greddy-oil-cooler-m20xp1-5-block-adapter-type-e-use-3-4-16unf-oil-filter/
what oil filter relocation kit is that?
What exhaust manifold and radiator r u using?
Hey, that exhuast manifold was from TF-works and I’m still using my stock radiator with no problem at all.
Question bro did you delete your abs ?
Hey , yes I did and I re-did all the brake lines. It looks cleaner in my opinion. But everyone is different.😁