This whole time I've been wrapping grips incorrectly (starting at the bottom but using the wrong end of the tape). I applied a replacement grip after watching your video and this is by far the best wrap job I’ve done.
nice video but should've included the beginning of the wrapping, most amateurs tend to have a hard time making it nice and flush and it would help to explain some tips on how to get it started so there's no like overlap/wrinkles
Yeh, that woulda helped, but I guess as it’s not explained in the video I can try? All you gotta do is stretch the grip nicely, press inch-by-inch, till you’re able to go 3-4 levels down, and then you won’t have to stretch it too much and will be able to press the grip 3-4 inch-by-3-4 inch
Vinyl electric tape wont last month in the sun. Might as well say put oil on the handle, So bad advice. In your reply, you will say "it stays on for me". They made tennis grip tape for a reason. Both the same price as high quality vinyl tape vs tennis griptape of decent quality. For the future, dont take this tip. He will hope u have a slippery racket when he plays a game with you!🤣😂🤣😂
@@PROUDxRUSHxDENIER I was talking about the finishing tape and if you’re still saying that it won’t last I’ve kept mine on for five months and it’s still fine. I’ve edited my comment. My bad.
The most difficult part for me is the start and when you begin winding with an angle - unfortunatly this was not shown. Other than that - great video 👍
Very nice that Floyd makes the difference between right- versus lefthanded players. I am not sure if everyone understands the staple issue... However: a very nice instruction, thanks you Tennisware house and give my love to Bethanie Mattek Sands!!
Just used this as a guide to do a replacement on my sons racket, however, it turned out I didn't really need it and I have to highly recommend the Wilson replacement grip as not only is the grip marked to show the overlap but also the cutting line at the end is marked. 5 minutes later and it's just like it came from the factory. Also I'd highly recommend getting some Shellite (lighter fluid) and cleaning all the factory glue so there is no bumpy remains underneath.
Thanks so much. I always thought i need to use every last inch of my grip so i let them overlap too much. Never thought of cutting the extra off in the end
I cannot wait for Episode II, where Troy shows all the parts of re-gripping that are *actually tricky*. Like the first two-and-a-half wraps on the buttcap (which is actually what I came hoping for). Also, it would be nice to see how it goes when you staple the starting end: What bevel do you put it on? Where do you locate the staple? Can you get buy with a J-21 or T-50 hand stapler? These questions remain a mystery until we get a "deep dive" on those parts. (Also discussing grip weights, and how to weigh the old grip, then the new one, so you'll know the grams you're likely to add. (I trimmed about 3 gm to finish the top nicely, so that kind of thing is useful to plan for.) Cheers, /Acey
You don't need the staple. Bevel does not matter, however be consistent amongst your racquets. Angle the start of the grip a little inwards so that it doesn't come unraveled. Make sure you cover the entirety of the very end of the buttcap, 360 degrees. Pull the grip just tight enough so that it comforms and there are no bubbles. Do not stretch the grip to the point of deforming. Then begin to angle upwards. The overlap is up to you, however there is often a line to follow. Try to get into that pattern as soon as you can. Proper overlap is actually a slight "underlap". You do not want the grip to be entirely flat. If you look at a stock grip you'll see what I mean. After the buttcap part you can pretty much wrap with the tension of a regular overgrip. If you still have questions come drop by my discord and I'll be happy to help: discord.gg/7b8FG6
I used to always wrap my grips lefty, replacement grips and overgrips, a long while ago. But then it got to the point where I just became used to how the racquets come stock, wrapped for the majority, which is right handed. Another reason being that when we playtest racquets, we usually share one frame between 4 testers, so I just go with the right handed grip for the group. Troy, TW
@Johnny Do, This video is to replace the stock grip that comes with your racquet, typically you would do so if it is worn out/dirty. Most of the time, you don't need to replace the stock grip very often, if you use overgrips. Overgrips are very thin, and do not have adhesive on the back of them, as they are designed to be wrapped on top of the stock (base) grip. Troy, TW
Hey Troy - qq for you. I see so many different ways to start the grip, some on bevel 6, some on any short bevel, some halfway on the longer bevel and like this one at the start of the longer bevel. What is the correct way haha? Thanks!
Not for certain if there is a correct spot for all racquets. Usually we recommend to find the spot, where the factory stapled the grip at, and use that as the reference starting point for the replacement grip. Some of the more recent Wilson butt caps have come with like a little flap, or clip to slide the tip of the grip into, and sort of anchor the grip as you pull on it, so that usually is a starting point for those racquets. Troy, TW
Yeah sorry about that, it got cut from the video although that is usually the toughest part. But the key is to pull tight to reduce the bunching up of the grip, and there will be a bit more overlap on that first full turn. Even with factory wrapped grips you will often notice a bit more overlap or a slight bump on that first full rotation around the handle. I will try and do a UA-cam shorts video, where I show that part. Troy, TW
I think the cleanliness of the starting wrap, and not having too much overlap with each turn is most important, so that it doesn't feel bumpy, or lumpy. Other than that if it feels good in your hand, and hopefully still retains some of the shape, and feel of the pallet underneath, then it really comes down to your preference. However, if you are in the industry or do home stringing/customization for other clients, then usually you want to stick with the industry standard, or as close to the factory gripping as possible. Troy, TW
I'm a bit slow lol when you take the old wrap off the handle is there still cushioning on it or is it just the bare hard handle? My old grip is sort've tearing and it seems there's a weird cushioning under it that may be tearing as well so I'm not sure if that must come off as well or if it's still just the wrap (nvm I am slow lmao it's just a rlly thick wrap that I have on it)
If you are removing the current or existing stock grip from the handle, you would ideally want it to come all the way off, leaving the hard pallet surface underneath with nothing on it. Then you would start to wrap, or install the new grip, on that clean hard surface. Troy, TW
Usually you want to start the grip at the point where the manufacturer does, which can usually be determined by where the grip stale is at when you remove the stock grip. Yes we do, www.tennis-warehouse.com/searchresults.html#search=products&searchtext=finishing%20tape&opt_page=1&opt_sort=alphaAtoZ&opt_perpage=100. Troy, TW
The flare was similar before and after the re-gripping. These Dunlop racquets do not have much of a flare to begin with. If you want to add some flare to the butt cap, you can wrap some layers of athletic tape, prior to applying the replacement grip. Troy, TW
Each grip, and overgrip you purchase comes with tape to finish off the grip, or you can get a roll of it, like this: www.tennis-warehouse.com/Tourna_Vinyl_Finishing_Trim_Tape_Black_/descpageUNIQUE-UFTB.html. Troy, TW
Hello Troy! How is it going man? Hope you and you loved ones are doing good. What’s the weight and the thickness of the Wilson Sublime and the Pro Performance base grips?
It depends, if it like most of brands that have a double sided tape on the grips, you might be able to peel it of carefully. But some brands like Yonex who use some sort of glue, you might need a bit more elbow grease, or I have tried using like a putty scraper, that you would find at a hardware store, and maybe a blow dryer to heat up the surface and soften up the adhesive residue. Just be careful if you do use a scraper to not dig into the pallet. Troy, TW
Do you have some suggestions of good replacement grips? I replaced the original grip of my Babolat Pure Drive by the same one (Babolat Syntec I think) but I don't find it very good. I use overgrip on the top of it but the foam of the original grip isn't very durable. I'd like something comfortable (enough foam) but firm not spongy such as some other grips. Some years ago I tried Wilson shock shield grip and found it quite good and comfortable but I can't find it anymore in Europe. Thanks
I think it is more of a feel thing, when it comes to that. Since most of us use overgrips, we don't frequently change our replacement or base grips. I think after a long period of time the grips starts to lose some of its cushion, or becomes more firm, and maybe at that point it could use a replacement. Definitely would change it is the adhesive is no longer holding, and the grip is coming off or separating. Troy, TW
I usually try cleaning it off as best as possible without damaging the pallet or molded surface under the grip. Sometimes I might use like a putty knife, or putty spatula to help scrape off some of the residue, but got be careful not to dig into the surface. I have also tried using our heat gun, to get some of the residue to soften up a bit, and then wipe it or scrape it off. Troy, TW
@@tenniswarehouse Thanks for the tips. I was able to remove some of the residue with by rolling my thumbs and also using a putty scraper. I also got good results with acetone and paper towels.
I am left handed player and I always install a replacement grip like righ handed player (I write with right hand). What would be the advantage to have the grip in opposite direction?
It is mostly a feel thing, as the spirals of the grips will be more inline with your fingers, as you grip the racquet. I am a lefty, and wrap my grips as they come stock, for a right hander. Troy, TW
Probably not the best idea, although it is possible, we typically find that you start to lose the feel of the handle, and the shape of the pallet. Troy, TW
Having put thousands of grips on tennis , squash and badminton rackets myself if you don't slightly stretch the grip when replacing it will probably come loose.
Skipped the most difficult part which is over lapping the end of the grip thats at the buttcap, while still angling it down to wrap the rest without getting a bubble.
Yes, it was edited out sorry about that. We did add on a short video knowing that part was missing. Check it out here: ua-cam.com/users/shorts_cFFHiulB7c. Troy, TW
Skipping the needle nose pliers at the start was annoying. We had to wwtch you do the whole grip removal which is the most obvious bit and then you skip something which im sure has to have tender care or maybe not
I don't have a supercharged staple gun and my regular staple gun can't penetrate handle. Just rolling on a replacement grip doesn't work for me: in humidity, with sweat, it just slides around until it loosens off. Here's what I do. I sourced copper tacks at the local hardware store (won't rust). I used a drill with a small bit to drill a hole in the handle--the bit width should be a tad less than the width of the tack. Take an awl and poke a hole through the grip at its end. THEN put it all together: tack through grip, use a tack hammer to lightly pound in the copper tack. Really holds.
Or just walk into any hardware store in the world and they will gladly let you use a staple gun for a quick staple. Same goes for many FedEx locations world-wide. If you don't want to buy the optional staple gun. Take care.
Wouldn't it be easier to take the old one off, lay it on top of the new one and cut the new one to match the shape of the old one, and then apply the new one.
Not necessarily the best idea, because various replacement grips will have different widths. So, if you cut them to the same length, and taper it off at the same point, they won't always end up covering the same amount of the grip, because a wider grip will cover more of the handle each time you wrap it 360 degrees. For example, Tourna Grip is an overgrip that comes in three different sizes, (standard, XL, and XXL). They are all the same length but with three different widths, the wider the grip the more it will cover. Troy, TW
Hmmm, not sure how it would work with the sticky side up? If it is a replacement grip they are using, not an Overgrip, then the adhesive side needs to be touching the pallet to keep the grip in place. If you went with the adhesive up, you would literally be grabbing a grip with tape on it, and the non-adhesive side would not keep the grip in place. So maybe they are talking about an overgrip, which do not come with adhesive attached to the grip. Troy, TW
@Kelly Latham, Apologies, we have had several issues with our CC over the years and have worked with UA-cam to resolve the issue. Some of our older videos, or even videos before 2022 may not have CC, but we are doing our best to get them updated. Looks like I was able to push through captions on this one. Thanks for letting us know it wasn't working! We will do our best to have CC on all our videos moving forward! Michelle, TW
Not meaning like a worn out grip that has lost all of its tack, and cushion, but as in a slightly used one, or even the stock grip that you are replacing with a different grip. You could use it to put on another racquet, that has a really worn out grip, or in certain cases we take the brand new stock grip off the handle, to customize the weight, and then put the stock grip back on. Troy, TW
Here is a video we did to supplement that part, ua-cam.com/video/_cFFHiulB7c/v-deo.html&lc=UgzEtxIBtBNvDH12vUV4AaABAg. But I think you viewed and commented on that short video. 👍 Troy, TW
haha, it was for show, but we definitely recycled it and put it on one of our racquets that had a much more worn out grip. All you need is a bit of double-sided tape, and re-apply it. Troy, TW
I actually do use them to help pull out the factory staple, it just wasn't shown in the video. You don't have to remove that staple, but some may notice it, especially when replacing with a thin grip. Troy, TW
This whole time I've been wrapping grips incorrectly (starting at the bottom but using the wrong end of the tape). I applied a replacement grip after watching your video and this is by far the best wrap job I’ve done.
Glad that this was helpful for you! Troy, TW
nice video but should've included the beginning of the wrapping, most amateurs tend to have a hard time making it nice and flush and it would help to explain some tips on how to get it started so there's no like overlap/wrinkles
Exactly!
Yeh, that woulda helped, but I guess as it’s not explained in the video I can try? All you gotta do is stretch the grip nicely, press inch-by-inch, till you’re able to go 3-4 levels down, and then you won’t have to stretch it too much and will be able to press the grip 3-4 inch-by-3-4 inch
Yeah, kinda dumb from him for not showing the beginning which is actuaöly the hardest part
@@lifeoftennis1285 Thanks for the stretching tip! Made all the difference!
thank you for this, very helpful! especially the part where you dot the grip.
Fantastic. Didn't insult my intelligence OR assume I already know certain details. Perfect video. Thanks a bunch!
If you don’t have the finishing tape electrical tape works fine too. Just a tip to future people.
but it doesnt grip. it will slip. my coach was so glad when i finally got a real grip
@@speechless1883 hes talking about the finishing tape at the end. To hold the actual grip together
Thanks.👍
Vinyl electric tape wont last month in the sun. Might as well say put oil on the handle, So bad advice. In your reply, you will say "it stays on for me". They made tennis grip tape for a reason. Both the same price as high quality vinyl tape vs tennis griptape of decent quality. For the future, dont take this tip. He will hope u have a slippery racket when he plays a game with you!🤣😂🤣😂
@@PROUDxRUSHxDENIER I was talking about the finishing tape and if you’re still saying that it won’t last I’ve kept mine on for five months and it’s still fine. I’ve edited my comment. My bad.
"How hard could this be?"
*Me, after 3 failed attempts and the racquet not exactly looking factory*
"Alrighty then. Screw it, looks close enough."
Very clever way how you finish the wrapping with the 2 dots; i am going to try this
The most difficult part for me is the start and when you begin winding with an angle - unfortunatly this was not shown. Other than that - great video 👍
I just replaced the original grip for my Pure Strike 18x20 (Version 1) after watching this video! Was super helpful, thanks!
Awesome, glad we could help!
Very nice that Floyd makes the difference between right- versus lefthanded players. I am not sure if everyone understands the staple issue... However: a very nice instruction, thanks you Tennisware house and give my love to Bethanie Mattek Sands!!
Thanks for this practical instruction,great video!
Now that’s how it’s done! Thanks for sharing.
Nice! Even though a simple procedure, good little tips for better install. Thanks!
Just used this as a guide to do a replacement on my sons racket, however, it turned out I didn't really need it and I have to highly recommend the Wilson replacement grip as not only is the grip marked to show the overlap but also the cutting line at the end is marked. 5 minutes later and it's just like it came from the factory.
Also I'd highly recommend getting some Shellite (lighter fluid) and cleaning all the factory glue so there is no bumpy remains underneath.
Thank you! this was super helpful for me changing my first grip :)
What a smooth video, well done TW
Thank you, very helpful! First time doing this, and it was easy to follow :)
One 16th of an inch. What the hell is that. That's ridiculous :) Say no to imperial units :P
😂
Haha I thought the same 😅
Maybe 1/870th of a foot is easier?
Finally replaced my old grip and this video helped a lot, thanks!
Thanks so much. I always thought i need to use every last inch of my grip so i let them overlap too much. Never thought of cutting the extra off in the end
awesome. I don't often play tennis but I've collected some vintage Racquets from the 80s, going to rewrap it 😎🤙🏽
Clean 👌🏽
This was super useful, thanks
Thanks, Troy! I wanted to switch to a thinner grip and this was really helpful!
This was a really good help thank you especially for beginners
Really good video 😊
Thanks bud. Worked a treat!
I cannot wait for Episode II, where Troy shows all the parts of re-gripping that are *actually tricky*. Like the first two-and-a-half wraps on the buttcap (which is actually what I came hoping for). Also, it would be nice to see how it goes when you staple the starting end: What bevel do you put it on? Where do you locate the staple? Can you get buy with a J-21 or T-50 hand stapler?
These questions remain a mystery until we get a "deep dive" on those parts. (Also discussing grip weights, and how to weigh the old grip, then the new one, so you'll know the grams you're likely to add. (I trimmed about 3 gm to finish the top nicely, so that kind of thing is useful to plan for.)
Cheers, /Acey
You don't need the staple. Bevel does not matter, however be consistent amongst your racquets. Angle the start of the grip a little inwards so that it doesn't come unraveled. Make sure you cover the entirety of the very end of the buttcap, 360 degrees. Pull the grip just tight enough so that it comforms and there are no bubbles. Do not stretch the grip to the point of deforming. Then begin to angle upwards. The overlap is up to you, however there is often a line to follow. Try to get into that pattern as soon as you can.
Proper overlap is actually a slight "underlap". You do not want the grip to be entirely flat. If you look at a stock grip you'll see what I mean. After the buttcap part you can pretty much wrap with the tension of a regular overgrip.
If you still have questions come drop by my discord and I'll be happy to help: discord.gg/7b8FG6
Many thanks!
Thank you!
Troy, as a fellow lefty, do you ever wrap for lefty?
I used to always wrap my grips lefty, replacement grips and overgrips, a long while ago. But then it got to the point where I just became used to how the racquets come stock, wrapped for the majority, which is right handed. Another reason being that when we playtest racquets, we usually share one frame between 4 testers, so I just go with the right handed grip for the group. Troy, TW
Just found you guys on UA-cam! Gona place a order today love your prices!!
Thank you! The dots are usefull!!!
I would have liked to see the very beginning of the wrapping...
Wait so any normal racket do you add a new grip over the one it comes with pre made or do you peel that off before applying the new one
A racket comes with a stock ‘base grip’. You can add an overgrip over that grip. In this video, he mentions how to remove and replace the base grip.
@Johnny Do,
This video is to replace the stock grip that comes with your racquet, typically you would do so if it is worn out/dirty. Most of the time, you don't need to replace the stock grip very often, if you use overgrips. Overgrips are very thin, and do not have adhesive on the back of them, as they are designed to be wrapped on top of the stock (base) grip. Troy, TW
Perfect, you're a lifesaver.
Is the replacement grip in the video closer to 25mm or 22mm width?
The grip in this video is the Gamma Hi Tech Grip, which is closer to 25mm in width. It is 26.9mm to be more precise. Troy, TW
Hey Troy - qq for you. I see so many different ways to start the grip, some on bevel 6, some on any short bevel, some halfway on the longer bevel and like this one at the start of the longer bevel. What is the correct way haha? Thanks!
Not for certain if there is a correct spot for all racquets. Usually we recommend to find the spot, where the factory stapled the grip at, and use that as the reference starting point for the replacement grip. Some of the more recent Wilson butt caps have come with like a little flap, or clip to slide the tip of the grip into, and sort of anchor the grip as you pull on it, so that usually is a starting point for those racquets. Troy, TW
@@tenniswarehouse Good tip, appreciate the response as always!
If i may know ,the finishing tape u use is that a regular electrical tape?
You can use electrical tape, but we were using this one: www.tennis-warehouse.com/descpage-GFTB.html. Troy, TW
Thanks troy..
Very helpful.
Beautiful. Will be using this technique to wrap a gamma leather grip into an archery bow inshaAllah 👍🏼
hOW DID YOU START THE WRAP BETWEEN TIME 2:21 AND 2:22
Yeah sorry about that, it got cut from the video although that is usually the toughest part. But the key is to pull tight to reduce the bunching up of the grip, and there will be a bit more overlap on that first full turn. Even with factory wrapped grips you will often notice a bit more overlap or a slight bump on that first full rotation around the handle. I will try and do a UA-cam shorts video, where I show that part. Troy, TW
I always put the tapered side up lol. So that the sticky bit on the end would stick on the handle. Is that bad?
I think the cleanliness of the starting wrap, and not having too much overlap with each turn is most important, so that it doesn't feel bumpy, or lumpy. Other than that if it feels good in your hand, and hopefully still retains some of the shape, and feel of the pallet underneath, then it really comes down to your preference. However, if you are in the industry or do home stringing/customization for other clients, then usually you want to stick with the industry standard, or as close to the factory gripping as possible. Troy, TW
I'm a bit slow lol when you take the old wrap off the handle is there still cushioning on it or is it just the bare hard handle? My old grip is sort've tearing and it seems there's a weird cushioning under it that may be tearing as well so I'm not sure if that must come off as well or if it's still just the wrap (nvm I am slow lmao it's just a rlly thick wrap that I have on it)
If you are removing the current or existing stock grip from the handle, you would ideally want it to come all the way off, leaving the hard pallet surface underneath with nothing on it. Then you would start to wrap, or install the new grip, on that clean hard surface. Troy, TW
Hi, do you have a recommendation on which double sided tape to use when needed?
We typically use something like a 3M double sided masking tape, and it comes in a roll. Troy, TW
Troy - do you start applying the grip on the flattest part of the grip?
Also - does TW sell "finishing tape"
Usually you want to start the grip at the point where the manufacturer does, which can usually be determined by where the grip stale is at when you remove the stock grip. Yes we do, www.tennis-warehouse.com/searchresults.html#search=products&searchtext=finishing%20tape&opt_page=1&opt_sort=alphaAtoZ&opt_perpage=100. Troy, TW
I use electrical tape - holds and you can get colors.
Thank you for the tutorial, but I notice you've lost some of the flare at the end of the buttcap. Doesn't that directly affect the feel?
The flare was similar before and after the re-gripping. These Dunlop racquets do not have much of a flare to begin with. If you want to add some flare to the butt cap, you can wrap some layers of athletic tape, prior to applying the replacement grip. Troy, TW
Does it take a while for the replacement grip to properly mold to your hand?
Not typically, I usually find them to feel good right away. Troy, TW
What is that finishing tape you use ?
Each grip, and overgrip you purchase comes with tape to finish off the grip, or you can get a roll of it, like this: www.tennis-warehouse.com/Tourna_Vinyl_Finishing_Trim_Tape_Black_/descpageUNIQUE-UFTB.html. Troy, TW
Thanks Bud
Thank you
Hello Troy! How is it going man? Hope you and you loved ones are doing good. What’s the weight and the thickness of the Wilson Sublime and the Pro Performance base grips?
Does normal duct tape work instead of the finishing tape ?
Electrical tape
Electrical tape is the best option. Troy, TW
What’s the best way to remove the adhesive from the grip handle
It depends, if it like most of brands that have a double sided tape on the grips, you might be able to peel it of carefully. But some brands like Yonex who use some sort of glue, you might need a bit more elbow grease, or I have tried using like a putty scraper, that you would find at a hardware store, and maybe a blow dryer to heat up the surface and soften up the adhesive residue. Just be careful if you do use a scraper to not dig into the pallet. Troy, TW
Do you have some suggestions of good replacement grips? I replaced the original grip of my Babolat Pure Drive by the same one (Babolat Syntec I think) but I don't find it very good. I use overgrip on the top of it but the foam of the original grip isn't very durable. I'd like something comfortable (enough foam) but firm not spongy such as some other grips. Some years ago I tried Wilson shock shield grip and found it quite good and comfortable but I can't find it anymore in Europe. Thanks
@PierreM BK,
I would consider Head HydroSorb Comfort, Tecnifibre X-TRA Full, or Wilson Cushion Pro replacement grips. Troy, TW
@@tenniswarehouse thanks Troy :-)
Babolat Xcel Gel is great.
Assuming the use of an overgrip how often should you replace the replacement grip?
I think it is more of a feel thing, when it comes to that. Since most of us use overgrips, we don't frequently change our replacement or base grips. I think after a long period of time the grips starts to lose some of its cushion, or becomes more firm, and maybe at that point it could use a replacement. Definitely would change it is the adhesive is no longer holding, and the grip is coming off or separating. Troy, TW
What to do when old grip has partially disintegrated and leaves a lot of residue on the handle? Thx
I usually try cleaning it off as best as possible without damaging the pallet or molded surface under the grip. Sometimes I might use like a putty knife, or putty spatula to help scrape off some of the residue, but got be careful not to dig into the surface. I have also tried using our heat gun, to get some of the residue to soften up a bit, and then wipe it or scrape it off. Troy, TW
@@tenniswarehouse Thanks for the tips. I was able to remove some of the residue with by rolling my thumbs and also using a putty scraper. I also got good results with acetone and paper towels.
Go Pack go! Love the watchTroy.
Thanks, Go Pack Go!
Is the replacement grip supposed to be smooth or slightly ridged? I know it can be either, but just as far as stock goes.
There is usually a little ridge, on the first overlap, but besides that it should feel pretty ridge-less, or nice and smooth. Troy, TW
I am left handed player and I always install a replacement grip like righ handed player (I write with right hand). What would be the advantage to have the grip in opposite direction?
It is mostly a feel thing, as the spirals of the grips will be more inline with your fingers, as you grip the racquet. I am a lefty, and wrap my grips as they come stock, for a right hander. Troy, TW
Thanks
It's finally here
How do you replace curved racket grips?
Not sure what you are referring to? Curved handle? Troy, TW
Mooi griptapie erom gedaan met jaarclub genoot. 10/10, mijne zit er beter omheen. Die van rik is dik.
this is the most beautiful thing ive ever seen
Guys i wanna know about putting 2 replacement grips
Probably not the best idea, although it is possible, we typically find that you start to lose the feel of the handle, and the shape of the pallet. Troy, TW
Wal mart 3 pack black Wilson...ultra wrap 2.97 no need to overpay.❤
I saw that Wawrinka, Dimitrov, Gasquet, etc, use leather grips. Those are over the replacement grip or they remove it to put the leather one on?
@Jack Ramirez,
They usually remove it and add a leather grip as the replacement grip.
Michelle, TW
leather grip is much more difficult to install, please show to install leather grip
Finally I learnt how to “get a grip”
Having put thousands of grips on tennis , squash and badminton rackets myself if you don't slightly stretch the grip when replacing it will probably come loose.
As a left hander myself I'm more impressed about how you managed to use right handed scissors ahahahah
Skipped the most difficult part which is over lapping the end of the grip thats at the buttcap, while still angling it down to wrap the rest without getting a bubble.
Yes, it was edited out sorry about that. We did add on a short video knowing that part was missing. Check it out here: ua-cam.com/users/shorts_cFFHiulB7c. Troy, TW
Skipping the needle nose pliers at the start was annoying. We had to wwtch you do the whole grip removal which is the most obvious bit and then you skip something which im sure has to have tender care or maybe not
Removed some perfectly good grip off that racket. couldn't find a junk one?
We re-used that grip on a racquet that had a worn out grip. Troy, TW
Anyone else here because of Adam Winrich's 15 minute bullwhip.
I don't have a supercharged staple gun and my regular staple gun can't penetrate handle. Just rolling on a replacement grip doesn't work for me: in humidity, with sweat, it just slides around until it loosens off. Here's what I do. I sourced copper tacks at the local hardware store (won't rust). I used a drill with a small bit to drill a hole in the handle--the bit width should be a tad less than the width of the tack. Take an awl and poke a hole through the grip at its end. THEN put it all together: tack through grip, use a tack hammer to lightly pound in the copper tack. Really holds.
Or just walk into any hardware store in the world and they will gladly let you use a staple gun for a quick staple. Same goes for many FedEx locations world-wide.
If you don't want to buy the optional staple gun.
Take care.
Wouldn't it be easier to take the old one off, lay it on top of the new one and cut the new one to match the shape of the old one, and then apply the new one.
Not necessarily the best idea, because various replacement grips will have different widths. So, if you cut them to the same length, and taper it off at the same point, they won't always end up covering the same amount of the grip, because a wider grip will cover more of the handle each time you wrap it 360 degrees. For example, Tourna Grip is an overgrip that comes in three different sizes, (standard, XL, and XXL). They are all the same length but with three different widths, the wider the grip the more it will cover. Troy, TW
@@tenniswarehouse yes of course it wouldn't work if the width isn't the same, What is a comfortable synthetic grip??. thanks
My wife needs to get a grip..
I just did mine, it looks like shit, but I’ll know better for next time ... thanks 🥲
👍👍👌👌
Some vids say sticky side down, some say sticky side up.
Hmmm, not sure how it would work with the sticky side up? If it is a replacement grip they are using, not an Overgrip, then the adhesive side needs to be touching the pallet to keep the grip in place. If you went with the adhesive up, you would literally be grabbing a grip with tape on it, and the non-adhesive side would not keep the grip in place. So maybe they are talking about an overgrip, which do not come with adhesive attached to the grip. Troy, TW
1/16 of an inch … only in America 🤯
Please set up Close caption I'm deaf
@Kelly Latham,
Apologies, we have had several issues with our CC over the years and have worked with UA-cam to resolve the issue. Some of our older videos, or even videos before 2022 may not have CC, but we are doing our best to get them updated. Looks like I was able to push through captions on this one. Thanks for letting us know it wasn't working! We will do our best to have CC on all our videos moving forward!
Michelle, TW
You didn’t show the hardest/worst part of gripping the bottom of the handle lol
Which is why we added this short :) be sure too check it out!
ua-cam.com/users/shorts_cFFHiulB7c?feature=share
Michelle, TW
Why on earth would you reuse the old grip?
Not meaning like a worn out grip that has lost all of its tack, and cushion, but as in a slightly used one, or even the stock grip that you are replacing with a different grip. You could use it to put on another racquet, that has a really worn out grip, or in certain cases we take the brand new stock grip off the handle, to customize the weight, and then put the stock grip back on. Troy, TW
@@tenniswarehouse Ah I see, thanks for the insights! Nice video :)
Thanks for skipping literslly the most crucial part of the wrapping lol
Here is a video we did to supplement that part, ua-cam.com/video/_cFFHiulB7c/v-deo.html&lc=UgzEtxIBtBNvDH12vUV4AaABAg. But I think you viewed and commented on that short video. 👍 Troy, TW
I hate grip bands, I think they are not needed. Yep just my personal opinion
it pains me how he removes a brand new grip
haha, it was for show, but we definitely recycled it and put it on one of our racquets that had a much more worn out grip. All you need is a bit of double-sided tape, and re-apply it. Troy, TW
tidy
lmfao no one has ever used a needle nose plier heck you didn't even use one lmao
I actually do use them to help pull out the factory staple, it just wasn't shown in the video. You don't have to remove that staple, but some may notice it, especially when replacing with a thin grip. Troy, TW
:-)