As someone that is new to BMW and the scanner, this was the most helpful video that I've found so far! I hope you continue to put out videos. Thanks a lot!
LED bulbs actually have much higher resistance, and therefore the current is very low. That is why the LCS detects an open circuit when a conventional bulb is replaced with an LED. But I'm just nitpicking, great video and very informative!
good vid and explains really good how the software operetes I have this unit 1.4.0but am finding it a bit hard to install ...something to do with drivers one question...my 04 325 E46 is a bit thirsty so can this program reset your fuel economy back to factory of maybe there is a code fault
Fault is with the catalytic converter, it’s reading too high and the o2 sensors tell you there’s a problem, change the cat and the errors will go the problem is the cat!
Thanks, managed to get the error light off my dash for rear lights after changing (and coding milage into) the LCM Quick query, I unticked cold check, hot check and BC message. Was that right or wrong? You only appear to ubtick cold check?
Hi Xion Unjust love the video. 2 questions though. 1. Where do I but the PA Soft / BMW Scanner 1.4 2. I was wondering if I could reprogram a used cluster with this.
I have a 1998 BMW Z3. There is a 20 pin connector under the hood to read dealer service dept codes. My guess is PA Soft / BMW Scanner 1.4 can not read the dealer codes. ????????????? Is that correct?
Quick question. If I swap out my ZKE/GM5 do i just need to re-code/re-sync my key FOB/remote to get it to work?? I heard that I had to "reprogram," or "re-code" the GM5 to my vehicles VIN. However I have plugged in the new GM5 and I don't see any problems or non functions except for the key FEB remote. Everything else works perfect. I can lock and unlock all doors, roll up and down all windows with my key FOB remote from turning and holding the drivers door lock. What else is there to do?
can you change the odometer numbers. i put a used cluster on my car, because my old one burned, and was wondering if i can change the numbers to the correct ones.
Would you happen to now if this tool will allow you to code the Nav system options? I need to recode my MK4 Nav to match the car.. Normally this would be done with an I-Bus interface, I think..
where did you get the scanner i got same one off ebay and it read only DME i did solder pins 1-2 did not help and i also solder pins 7-8 and that also did not help
Yea, it still is though because I have to physically fix a wiring issue. It will reset the codes and you can code the car for things that can be done at the dealership which will cost over $100 or so. Resetting the car by just having it reset the adaptations (the way you drive the car) so it can re-learn if you drive aggressive, slow, etc.
have this unit but have a question when I go to DME to check on data ...will not go into live data it is not highlighted also I want to have side mirrors to retract when ignition is off have you any suggestions
Is it possible to re-code the speedometer kilometers? My current speedometer is bad, and i got a new one, but it has much more miles than my current one.
where do you buy this? Does it have options to see live stats (MPH,Air Fuel Ratio ETC) and did you have to do any soldering or modifying of the device to be able to use properly? For instance to turn drl off, traction control off, abs off, etc etc ...
thank u sir , i'll have to buy the 20 pin socket adapter for this also for 2000 and less models e39?? BMW OBDII ROUND DIAGNOSTIC SCANNER ADAPTER 20 PIN CABLE????
Friend, can you handle this on ebay , costs approximately EUR 17.85. Check out this announcement : www.ebay.com/itm/iCarsoft-BMW-20-epingle-Pour-16-Pin-Obd-II-Obd2-Cable-Adaptateur-Officiel-Fil-/271702378157?pt=LH_DefaultDomain_71&hash=item3f42b946ad Hope this helps . att . Mark / Brazil
Marcos Nascimento thanks man,, sure it helps,, gues all together the device and the connection is woorth it to buy,, and as i checked the forums its even better to buy this connection than the one inside the car, thanks for ur reply
one question though, these guys dont make it clear in the description which version of the software comes with the cable, but it seems like there is a full version (looks like what you have) and on that one cost 650us according to the information on that site
Hi, I got this scanner a bout a week ago, and its awesome, but I'm trying to stop my heater from coming on every time I start the car, is the PA soft capable of performing such a task? I've already coded a few things but the heater is really bugging me.
+e30BMW4ever Usually it's not a coding issue from what I know. Do you turn off the heater before turning off the car? If you don't then the car will store that it was on and will turn it on next time you turn the key to position 2
+Xion Unjust (Solidjake) Thanks for the reply. Yes, I turn of the heater before turning the car off. But next time I start the car the heater comes on again. The temperature value at which was set stays stored every time, but regardless, every time I turn the key to position 2 it comes back on. My car is a 2000 E46 325ci. I wonder if changing the old style 10 button climate control unit would help. BTW, I've seen a lot of your threads on e46fanatic and your E46 is just awesome!
My clock changer knob is broken on my instrument cluster and it shows no time at all neither on the radio or the cluster. could i change it with this???
Hi mate! Please help if you can. I can not acces Live data from dde menu...I can see errors(no error for me) but live data is greyd out...I have tried to solder pin 1 and 2, to solder pin 4-5, to solder pin 7-8 , to install a new ,different, copy of program, to run it on win 7 and win xp-BUT NOTHING! What should I do? THANK YOU!
What year model is your E46? I have a 2005 325ci and the light coding doesn't work. Menus pop up, I can write new codes, but no change to the lights! The canbus error message delete works though, but no light coding. Any ideas? Everything else in the software works.
+Xion Unjust (Solidjake) Us blinks. I have the EU model with separate parkbulbs in the headlight. I can choose options and press write code, it even comes up as succesful but nothing happens to the actual lights. No change at all.
Hey man. Great vid! one question..do i need to leave the ket in position one once the software has loaded? i dont want to run the battery dead while coding haha
hi, if u can answer this i would be so thankful, i just got the 1.4.0 scanner because im having some troubles with my abs, i scanned it for fault codes but then on the abs it said "not found" do you know what the problem is?
my e46 moonroof windowns all down sometime car is on the strret how to fix by this soft , can i disable remote opening windows so the windows wont goes down
Hello, I have this software for my e38 740. I have used it successfully on the 20 pin connector under the hood to check fault codes and reset DTC for various issues. I can't seem to use it though on the 16 pin OBD II connector inside the car. I get an error message that it can't connect to IKE. Any reasons why?
+Leo H found it on another youtube clip. it's under IKE. I was be able to code my new install factory alarm. I haven't tried to change the oil service interval yet but I want to change it from 15k to 7k
Hey, I have an e53 and trying to deactivate the error message on my dash that say “self level suspension inactive” can I do this through the PA soft? Keep in mind the factory self level has been replaced with a separate air suspension kits with a compressor. Any help would be appreciated!
Hi mate, have you succeeded with your e53? Could you please share the steps, I’ve switched my air bags to coil overs, wanna delete self level suspension on dash. Thanks.
hi. I have a 2004 bmw 320i. I just purchased an uncut key with the security chip in it however from what i was told even if i have a locksmith cut me a key the car will not start as the key is not programmed to the car(anti-theft) My keyfob that came with the car is in bad shape and i tried replacing the battery and had no luck. BMW wants way to much for a new keyfob so i purchased one online. The retailer told me the only thing i had to do was get it cut and then have BMW ensure the anti theft chip is coded to the car. Issue is ..that BMW want to make money and want to sell you a key for 300$...Would this programmer allow me to program the car to my new key? I know how to program the key to unlock lock doors etc..but i am referring to the anti theft portion of the key that has a chip that only works with the car it is paired to. So will this BMW scanner allow me to pair the key and avoid going to BMW ? Hope i explained it properly so you can understand my issue at hand. Thanks
+Andre M Hey Andre, that I am not too sure about sorry to say. Please join e46fanatics forum and post in the General E46 section. They will help you out there. Just say Solidjake referred you.
Thanks man. I AL already a member of most of the forums but thanks for the suggestion anyways. I have read so many posts my head hurts. .lol. some say local dealers will. ..some say no need just cut and go and some say nothing can be done unless I know someone with some very specialized equipment etc. ...so I just figured I would ask here....again...thanks bud
Is it possible to disable the Brake Pad Wear Sensor on the instrument cluster? I have tried every possible way known to reset the light and it won't go away.
Hey Mike, did you replace the sensor? If the light came on due to low brake pad material then it must be replaced. After it is replaced you have to put the key in position 2 (right before turning the car on) and leave it like that for a minute. Then the light will be off when you take the key out and turn on the car
I replaced the sensors and left the key on in the #2 position for over a minute and the lights did not go out. I then took a piece of wire and jumped both sensors, put the key in the #2 position for over a minute and the lights still remained.
My 2006 BMw e60 has a problem with SRS with my car and I am not sure that this program will work on my car or not. Please let me know if it works on my car.
@@flippy9133 Thanks bro. Until now, I already know this, I also got INPA. I resolved the issues on my car and got another car afterwards. Damn, how the time flies. A lot has happened in .... 5 years.
Hello there,just wondered if you could share the BMW Scanner 1.4 with me,could you make the virtual copy of a disk with BMW Scanner 1.4 and the drivers and send it to me please? Thank You in advance. Alex
hy xion i have a e39 1997 and i have a problem on LCM when i press to coding data and light coding i seee this message No coding available for this index, yet!" please help me with this!!!
Does anybody know where to download the drivers for the scanner for Windows 8.1 64bit? The enclosed mini-disk enclosed is only for XP and Win 7. Thanks
I made the mistake on ews / manufacturer settings. To change the dme/dde version from version 2 to version 3. Now I am unable to start the car, tried endlessly to resolve with no solution and when trying to go back to selecting version 2 it simply will not save. Any ideas from anyone what to do here
I got load of things not working on my BMW 318Ci Se 2001 model UK spec. Alarm chirps and makes a high pitch noise constantly until I pull 1 of the 5 amp alarm fuses. The car starts with the fuse in place and alarm sounding and it still is making a high pitch noise whilst the engine is running. The Key fobs don't work and non of the functions on the Fobs work, (Even fitted a new battery Panasonic VL2020 in 1 of them) No central locking, on the Fobs, on the Key, or inside the car on the button by gear shift. No windscreen wipers or washers. No electric windows on any of them on the car which has 4. No interior lights or no glove box lights. Left hand indicator flashes to fast until I operate the Hazard warning lights then when I switch the hazards off it works normally..The right side is fine. (All bulbs ok) The rest of the electrics seem ok, lights, dash lights, radio, cruise control and ASC and mirrors all work fine. So the question is really I am sure that my GM5 Module is in a serious way. Will this cable and scanner sort out my problems? There is so many scanners out there I have looked in to inpa NCSexpert and NSC Dummy but this looks a lot user friendly.. Any advice for me would be greatly appreciated, can you tell me what I need and where to get it from please should this be a resolution. I have to sort this asap..
Hey Daniel, no option for that that I know of. Is your fan not working properly? I would replace the sensor in the lower radiator hose and the big 50 amp fuse first.
my fan stopped working 3 weeks ago,my radiator blew as well because of the water getting too hot and me not being able to stop the car ar the right time,so i got a new fan but since my gasket had to be replaced too i dont have any way of testing the fan except with inpa,wanted to buy bmw scanner because its more user friendly,but since i can test the fan to see if it works only with inpa,had to for that
As someone that is new to BMW and the scanner, this was the most helpful video that I've found so far! I hope you continue to put out videos. Thanks a lot!
LED bulbs actually have much higher resistance, and therefore the current is very low. That is why the LCS detects an open circuit when a conventional bulb is replaced with an LED. But I'm just nitpicking, great video and very informative!
Thanks Jake. Sometimes generic codes don't help much. The local mechanic was eager to test the car for $80. "You got $80? You can go to the ATM." :)
Extremely clear. Thank you. Just getting this for my m3 CSL.
So that's what you sound like. Nice refresher course for me. Thanks Jake.
good vid and explains really good how the software operetes
I have this unit 1.4.0but am finding it a bit hard to install ...something to do with drivers
one question...my 04 325 E46 is a bit thirsty so can this program reset your fuel economy back to factory of maybe there is a code fault
Hi.. I have a bmw x5 e53 (2004) 3.0 diesel
Can i delete
SELF LEVELING SUSPENSION INACTIVE
with this software?
Thank you!
Fault is with the catalytic converter, it’s reading too high and the o2 sensors tell you there’s a problem, change the cat and the errors will go the problem is the cat!
Can you use this tool for eliminating the canbus warning for the headlights? if so can you explain how? thanks in advance.
i have the same problem
How do you reprogram the unlock button on the key fob to unlock all the doors, not just the drivers door???? Thanks for the vid.
GOD Thank you. # weeks or reading about "coding" and "programming" and then seeing this video makes it so simple. Thanks a lot!
for IKE / EWS issue: you have to solder pin 7 and pin 8 inside the scanner. It worked on my '99 323Ci.
Thanks, managed to get the error light off my dash for rear lights after changing (and coding milage into) the LCM
Quick query, I unticked cold check, hot check and BC message. Was that right or wrong? You only appear to ubtick cold check?
Hi Xion Unjust love the video. 2 questions though.
1. Where do I but the PA Soft / BMW Scanner 1.4
2. I was wondering if I could reprogram a used cluster with this.
+gregory douglas Hey, you can check amazon or a seller named xcar360. should be around $25-35 What programming you want to do exactly?
Are you able to scan ABS/ESC , Clean Oil Service Dashboard, Reset Air Bag Lights with this program!?
I have a 1998 BMW Z3. There is a 20 pin connector under the hood to read dealer service dept codes. My guess is PA Soft / BMW Scanner 1.4 can not read the dealer codes. ????????????? Is that correct?
Quick question. If I swap out my ZKE/GM5 do i just need to re-code/re-sync my key FOB/remote to get it to work?? I heard that I had to "reprogram," or "re-code" the GM5 to my vehicles VIN. However I have plugged in the new GM5 and I don't see any problems or non functions except for the key FEB remote. Everything else works perfect. I can lock and unlock all doors, roll up and down all windows with my key FOB remote from turning and holding the drivers door lock. What else is there to do?
Can I calibrate my speedometer's hand that's constantly showing 6mph above the actual speed of the vehicle?
can you change the odometer numbers. i put a used cluster on my car, because my old one burned, and was wondering if i can change the numbers to the correct ones.
yes it can, change the milleage on the lcm then change the lcm vin to match with your new odo vin
Would you happen to now if this tool will allow you to code the Nav system options? I need to recode my MK4 Nav to match the car.. Normally this would be done with an I-Bus interface, I think..
Hi ,
Can you test parts such as ac compressor , vanos solenoids , o2 sensors with this program ?
Thanks
i cannot wait to receive this thing! great walk through !
Is there anyway to see all recorded kilometers/mileage to find out if they have been tampered with?
I see that ABS is on the list. How thorough is the test? Will it test each wheel speed sensor?
where did you get the scanner i got same one off ebay and it read only DME i did solder pins 1-2 did not help and i also solder pins 7-8 and that also did not help
Yea, it still is though because I have to physically fix a wiring issue. It will reset the codes and you can code the car for things that can be done at the dealership which will cost over $100 or so. Resetting the car by just having it reset the adaptations (the way you drive the car) so it can re-learn if you drive aggressive, slow, etc.
The options under mirror memory and locking conditions are grayed out for me. Do you know what causes that?
Just bought a Dinan 323i... Would using this with my Dinan Tune be an issue?
have this unit but have a question
when I go to DME to check on data ...will not go into live data
it is not highlighted
also I want to have side mirrors to retract when ignition is off
have you any suggestions
Does PA Soft also allow users to disable the secondary air sensor? I need to "delete" mine, and I'm trying to avoid a full tune.
Hy.i have the bmw scaner to.my problem is i cant code anything.pin 7and8 soldered.must i solde pin 1&2 or 4&5? Pls help.what is your configuration?
PA soft is good when it's working! Most times you need to use it you have to jump through hoops to get it to work. It always loses the drivers.
I've noticed the same thing. So what do you do, reinstall the software or just the drivers?
Can this tool align the Ews 3 om Bmw e46 318i N42 , 2002?
Is it possible to re-code the speedometer kilometers? My current speedometer is bad, and i got a new one, but it has much more miles than my current one.
If I have the 20 pin connector am I able to use this software for obd1
I have a 2004 bmw 745li will this work on it?
where do you buy this? Does it have options to see live stats (MPH,Air Fuel Ratio ETC) and did you have to do any soldering or modifying of the device to be able to use properly?
For instance to turn drl off, traction control off, abs off, etc etc ...
+Limited Look up the site XCAR360, they will have BMW SCANNER 1.4 for around $40 shipped
Is the p.a soft capable of disabling the rear o2 sensors and secondary air pump?
thank u sir , i'll have to buy the 20 pin socket adapter for this also for 2000 and less models e39?? BMW OBDII ROUND DIAGNOSTIC SCANNER ADAPTER 20 PIN CABLE????
That I am not 100% sure on, check out the forums and see what the guys say about the earlier models. You probably will need to get it.
Thanks
Friend, can you handle this on ebay , costs approximately EUR 17.85. Check out this announcement :
www.ebay.com/itm/iCarsoft-BMW-20-epingle-Pour-16-Pin-Obd-II-Obd2-Cable-Adaptateur-Officiel-Fil-/271702378157?pt=LH_DefaultDomain_71&hash=item3f42b946ad
Hope this helps .
att .
Mark / Brazil
Marcos Nascimento thanks man,, sure it helps,, gues all together the device and the connection is woorth it to buy,, and as i checked the forums its even better to buy this connection than the one inside the car, thanks for ur reply
one question though, these guys dont make it clear in the description which version of the software comes with the cable, but it seems like there is a full version (looks like what you have) and on that one cost 650us according to the information on that site
Hi
I have a BMW X3 E83 2.0D 2007 can this module be used on it?
If yes where and how can I buy it?
Is it possible to test the buttons of the cruise control with this software? (E46, PFL)
I have a 2003 BMW that the LCM went out replaced it with a used one how do I reprogram the new old lcm help
Your o2 code are set due to a vacuum leak in the vacuum lines or intake boots
Hi, I got this scanner a bout a week ago, and its awesome, but I'm trying to stop my heater from coming on every time I start the car, is the PA soft capable of performing such a task?
I've already coded a few things but the heater is really bugging me.
+e30BMW4ever Usually it's not a coding issue from what I know. Do you turn off the heater before turning off the car? If you don't then the car will store that it was on and will turn it on next time you turn the key to position 2
+Xion Unjust (Solidjake) Thanks for the reply. Yes, I turn of the heater before turning the car off. But next time I start the car
the heater comes on again. The temperature value at which was set stays stored every time, but regardless, every time I turn the key to position 2 it comes back on. My car is a 2000 E46 325ci. I wonder if changing the old style 10 button climate control unit would help.
BTW, I've seen a lot of your threads on e46fanatic and your E46 is just awesome!
Great video 👍
My clock changer knob is broken on my instrument cluster and it shows no time at all neither on the radio or the cluster. could i change it with this???
Hi mate! Please help if you can. I can not acces Live data from dde menu...I can see errors(no error for me) but live data is greyd out...I have tried to solder pin 1 and 2, to solder pin 4-5, to solder pin 7-8 , to install a new ,different, copy of program, to run it on win 7 and win xp-BUT NOTHING! What should I do? THANK YOU!
Can’t you make brake light flash with it too
What year model is your E46? I have a 2005 325ci and the light coding doesn't work. Menus pop up, I can write new codes, but no change to the lights! The canbus error message delete works though, but no light coding. Any ideas? Everything else in the software works.
+MarcusN What coding are you trying to do with the lights?
+Xion Unjust (Solidjake) Us blinks. I have the EU model with separate parkbulbs in the headlight.
I can choose options and press write code, it even comes up as succesful but nothing happens to the actual lights. No change at all.
Hey man. Great vid! one question..do i need to leave the ket in position one once the software has loaded? i dont want to run the battery dead while coding haha
and for some reason it doesn't read all modules? I have installed all correct drivers ect..
@@youmirinbro1 it scans for all bmw modules. e46's don't have every module, so yeah
in what module sits, bmw e38 seat occupancy sensor for off them through coding?
Autostop any luck finding it? Care to share?
hi, if u can answer this i would be so thankful, i just got the 1.4.0 scanner because im having some troubles with my abs, i scanned it for fault codes but then on the abs it said "not found" do you know what the problem is?
+william andersson What is the issue with the abs system exactly that you are having?
my e46 moonroof windowns all down sometime car is on the strret how to fix by this soft , can i disable remote opening windows so the windows wont goes down
will this work on my 1 series 2007 model?
Hello, I have this software for my e38 740. I have used it successfully on the 20 pin connector under the hood to check fault codes and reset DTC for various issues. I can't seem to use it though on the 16 pin OBD II connector inside the car. I get an error message that it can't connect to IKE. Any reasons why?
Could be as simple as faulty fuse
can you change the schedule maintenance service such as oil change, if so what module is it in? thanks.
+Leo H found it on another youtube clip. it's under IKE. I was be able to code my new install factory alarm. I haven't tried to change the oil service interval yet but I want to change it from 15k to 7k
Wich window that be use, how can we operate with windows7?
Hi. Where should I go to reset the airbag light.
Thanks
Hey, I have an e53 and trying to deactivate the error message on my dash that say “self level suspension inactive” can I do this through the PA soft? Keep in mind the factory self level has been replaced with a separate air suspension kits with a compressor. Any help would be appreciated!
Hi mate, have you succeeded with your e53? Could you please share the steps, I’ve switched my air bags to coil overs, wanna delete self level suspension on dash. Thanks.
how would i reprogram a gm5 module from a donor car? is that possible with this?
hi. I have a 2004 bmw 320i. I just purchased an uncut key with the security chip in it however from what i was told even if i have a locksmith cut me a key the car will not start as the key is not programmed to the car(anti-theft) My keyfob that came with the car is in bad shape and i tried replacing the battery and had no luck. BMW wants way to much for a new keyfob so i purchased one online. The retailer told me the only thing i had to do was get it cut and then have BMW ensure the anti theft chip is coded to the car. Issue is ..that BMW want to make money and want to sell you a key for 300$...Would this programmer allow me to program the car to my new key? I know how to program the key to unlock lock doors etc..but i am referring to the anti theft portion of the key that has a chip that only works with the car it is paired to. So will this BMW scanner allow me to pair the key and avoid going to BMW ? Hope i explained it properly so you can understand my issue at hand. Thanks
+Andre M Hey Andre, that I am not too sure about sorry to say. Please join e46fanatics forum and post in the General E46 section. They will help you out there. Just say Solidjake referred you.
Thanks man. I AL already a member of most of the forums but thanks for the suggestion anyways. I have read so many posts my head hurts. .lol. some say local dealers will. ..some say no need just cut and go and some say nothing can be done unless I know someone with some very specialized equipment etc. ...so I just figured I would ask here....again...thanks bud
+Xion Unjust (Solidjake) Hi!Thanx for very good video! Do you know any similar scanners for VAG and mercedes?And thanks again!
Is it possible to reset gearbox adaptations with this tool?
no you need inpa for that
@@flippy9133 Yeah, I already figured it out a long time ago, but thanks anyway
Picked mine up from bimmerstuff.com, super useful tool! I did the programming of the key.
What are those on the alarm key 1.2.3.4?? What they are for
No problem man, if you need help LMK. The coding for alarm/windows up are under Central Body and turning off DRL's are under the LCM.
hello can use this device to change vo/fa for e series
CANT SEEM TO FIND WHERE TO GET THE PROGRAME / P A SOFT FULL VERSION CAN YOU HELP
Thanks for the info oh and where can I by one at do u have the web site have a bless day
On Amazon look up BMW SCANNER 1.4. Should be around 25-30 usd
Am i correct in thinking that if you switch the alarm on /off or anything in coding you tick it then press write for it to work ?
yup, just enable the visual marks for the alarm and that's it. Click on audible if you have the pieces installed
Hi can you read reversing sensors.
Is it possible to disable the Brake Pad Wear Sensor on the instrument cluster? I have tried every possible way known to reset the light and it won't go away.
Hey Mike, did you replace the sensor? If the light came on due to low brake pad material then it must be replaced. After it is replaced you have to put the key in position 2 (right before turning the car on) and leave it like that for a minute. Then the light will be off when you take the key out and turn on the car
I replaced the sensors and left the key on in the #2 position for over a minute and the lights did not go out. I then took a piece of wire and jumped both sensors, put the key in the #2 position for over a minute and the lights still remained.
can you change the miles?
My 2006 BMw e60 has a problem with SRS with my car and I am not sure that this program will work on my car or not. Please let me know if it works on my car.
Yo , can I verify the fuel injectors with this tool ? Please respond , thanks !
no
@@flippy9133 Thanks bro. Until now, I already know this, I also got INPA. I resolved the issues on my car and got another car afterwards.
Damn, how the time flies. A lot has happened in .... 5 years.
@@w0wy haha, time flies. Sometimes I just reply to old comments for fun. Glad you got it resolved
Hello there,just wondered if you could share the BMW Scanner 1.4 with me,could you make the virtual copy of a disk with BMW Scanner 1.4 and the drivers and send it to me please? Thank You in advance.
Alex
no need.. the software is free
www.bmw-scanner.com/?page=bmw-scanner_v140&lang=eng
demo ver. doesn't let you do anything....
Where did u bought this Jake? Any links please . Thanks
Hi there. WIll this work with windows 8 installed?
hello i mistakely changed my ews2 to ews3 and i cant set it back to ews2 and i cant back up my settings. could u help please
will this software allow you to reset transport mode on my x5 (e53) if so where will it show up on program , thanks
it does :)
Hi dude I got a problem with the drivers. my pc is running in win 7 x64. so what kind OS you are using for this adapter ?
My understanding is it works best with Windows XP...
hy xion i have a e39 1997 and i have a problem on LCM when i press to coding data and light coding i seee this message No coding available for this index, yet!" please help me with this!!!
same problem, same car, did you find a solution ?
4:20 how did you fix that errror? I have airbag error too
Where can I find and download the current version of the software?
There is only this version as far as I know. Works well on XP
Does anybody know where to download the drivers for the scanner for Windows 8.1 64bit? The enclosed mini-disk enclosed is only for XP and Win 7.
Thanks
hey man. do you have any ideas why my is always come up with error hardware is not ready! i have my driver install and obd adapter is connected.
i made a video related to this problem
hardware is not ready or hardware faulty
ua-cam.com/video/FaDhcPrVlZ0/v-deo.html
@@3queensy917 thanks for the video.
I made the mistake on ews / manufacturer settings. To change the dme/dde version from version 2 to version 3. Now I am unable to start the car, tried endlessly to resolve with no solution and when trying to go back to selecting version 2 it simply will not save. Any ideas from anyone what to do here
Hello can you please send me the Software i lost my mini cd with it and the online version is just a demo version...
Will this work on an e39 m5?
I got load of things not working on my BMW 318Ci Se 2001 model UK spec.
Alarm chirps and makes a high pitch noise constantly until I pull 1 of the 5 amp alarm fuses.
The car starts with the fuse in place and alarm sounding and it still is making a high pitch noise whilst the engine is running.
The Key fobs don't work and non of the functions on the Fobs work, (Even fitted a new battery Panasonic VL2020 in 1 of them)
No central locking, on the Fobs, on the Key, or inside the car on the button by gear shift.
No windscreen wipers or washers.
No electric windows on any of them on the car which has 4.
No interior lights or no glove box lights.
Left hand indicator flashes to fast until I operate the Hazard warning lights then when I switch the hazards off it works normally..The right side is fine. (All bulbs ok)
The rest of the electrics seem ok, lights, dash lights, radio, cruise control and ASC and mirrors all work fine.
So the question is really I am sure that my GM5 Module is in a serious way.
Will this cable and scanner sort out my problems?
There is so many scanners out there I have looked in to inpa NCSexpert and NSC Dummy but this looks a lot user friendly..
Any advice for me would be greatly appreciated, can you tell me what I need and where to get it from please should this be a resolution.
I have to sort this asap..
Jon Boy - ever sort that out ?
hello , i have bmw e60 ,, 2003 year ... this scanner can test e 60?
Hey, this software does not since it's for E39/E46/E38 models
+ioseb iluridze You need PA Soft version 2.1.0 for the E60. Have a look at www.bmw-scanner.com
How to used this to reprogram the ecu
Thx for the video, very helpfull!
can you change the voltage going to the halo lights?
For E39's? I would not know since I've only coded on E46's
@@XionUnjust can you do it for E46?
@@KnowledgeLifestream No. E46's never had angel eyes (never made from factory for those 3 series models) so there is no such coding.
Great tutorial. Many thanks.
Emmissions section ?
is there an option in the p.a soft to turn the electric fan on.
Hey Daniel, no option for that that I know of. Is your fan not working properly? I would replace the sensor in the lower radiator hose and the big 50 amp fuse first.
my fan stopped working 3 weeks ago,my radiator blew as well because of the water getting too hot and me not being able to stop the car ar the right time,so i got a new fan but since my gasket had to be replaced too i dont have any way of testing the fan except with inpa,wanted to buy bmw scanner because its more user friendly,but since i can test the fan to see if it works only with inpa,had to for that
excellent video
How do I get the damn drivers?
which seller or vendor you get this from? Its hard to trust overseas sellers :\