Installing A Garage Door Part 4- Tensioning the EZ- Set Torsion Spring
Вставка
- Опубліковано 28 сер 2024
- This is an informational video only, for a comprehensive guide consult the owners manual, however I go over some key steps from start to finish.
THE ROLLERS WERE INSTALLED IN THE WRONG SPOTS IN THIS VIDEO, THEY HAVE BEEN CORRECTED. ALL IS WELL NOW.
In the last portion of the garage door odyssey we set tension on the garage door torsion springs via the EZ-set torsion spring winder which this door was equipped with.
Please note this is a 9x7 door, if it was a 16x7 foor door there would be two torsion springs and you would have to tighten each side gradually to keep them in sync.
![Garage Door Torsion Spring Replacement: How to by [Professional Tech]](http://i.ytimg.com/vi/5k9qrgZ9rPs/mqdefault.jpg)
Garage door repair services have emerged so that you can help people fix their doors and maintain their families safe and sound. Reston garage door repair Good Service !!
I was having a trouble getting the end bearing support seated into the bracket and this video was helpful. I like his just average Joe approach to the video.
Thank you for the video Joe, you did a good explaining how to use the EZ-Set units. I had never seen them before my neighbor got them & i'm installing them for him. This verified what I thought was the correct way to do it.
Shot of some Killer Safety Boots just before the 10 minute mark. You rock Joe! You Rock. I don't care what they say.
Thank you doing the video. You answered many questions I had doing my first torsion spring garage door.
Very informative video. Nicely done. I have installed three EZset systems at my home 14 years ago, myself. They are all on Ideal,16x7 insulated Four Star metal doors with "Sunrise" windows across the top panel. Each door has well over 6000 cycles. One about double that. They have all worked flawlessly. Never a single problem. I highly recommend them. I would also recommend using nylon wheels in place of metal ones if the garage is attached to your home. They're a lot quieter.
Simply done, Joe. Thanks for the tip.
Thanks for the video, I missed tightening the screws on the cable disc and the door kept erring all wack. I am about to hopefully fix the think once and for all!
😅
yeah i would definitely recommend that your hinges have slotted screwholes, makes the entire process easier.
Excellent videos!, thanks for your help!
my advise to your install is the hinges require that the slotted screwholes are on top and the rollers are to be installed in the hole furthest away from the door. if the rollers are not in the right holes the door face will not make proper contact to the jamb and the woodstop or weatherstrip will not be affective in keeping out drafts. also the spring will look swirly like a slinky when you have too much space between the coils when fully wound so your prestretch is too much, a little stretch will not look funky just my two cents.
Well done. Very helpful.
Very helpful video. I don't care what these other toolbags say. You threatened their manhood i guess.
I will indeed post here when I have the first problem, the north garage door gets used 99% of the time so the south door has been cycled maybe 30 times since new. We will see what gets it first, age or cycling. Thanks for the input!
yep you're right. if you look clearly he didn't install the rollers in the correct position as well.. im NO professional but I read instructions and follow them. ive installed garage doors 4 times.
Wow, this video warrants my making a video on how to properly install an Ideal/Clopay door. (palm to face)
Yes your absolutely right. Doh! They seem to work perfectly so im just going to leave them. Thanks!
Excellent ! Thanks
the noise can come from bad installation of side channels causing squeaking or on lintel contact with curtain the lubricate rollers at metal spindle side not on channel because that will cause collection debris the check axel fixing part thanks for sharing
Uhm, Joe, your rollers are in the hinged part of the hinge, and not in the roller holder part of the hinge. You need to move them to get proper offsets.
I don't doubt it the door come crashing down and crushed the roof of my car after 8 months in service......... just kidding. I have heard many stories about the EZ tension spring system being problematic. Mine has been in service for nearly 2 years and hasn't lost tension yet. The door is operated a minimum or 3 cycles a day sometime as many as 8. I figure its got 4300 cycles on it and so far everything is still works fine.
I dont doubt your information. The plastic stuff seems cheap.
I've noticed it's a crapshoot but most of my service comes in the winter months. I've had some that make it just a couple years and a few that have made it to 7-9 years. At least these are more serviceable than say a wayne dalton torquemaster. I don't service the TM at all and only do springs/cables on the EZ series. I usually recommend REAL nylon rollers at that point to just so I don't have to come back for years. Clopay has decent sections in the high end doors but still terrible hardware.
Yes I sure do miss the extra light. Overall I like these doors better because they hold some heat in whereas the filumas did not. If I lived in a moderate climate I would have went back with filumas most likely.
9:06 3M silicone paste is great for the retainers and everything else. 😀The paste doesn't run/drip unlike silicone spray.😑
The #2 and #3 hinges are upside down and like what was mentioned before the roller is in the wrong hole.
Lmao
I -think- they were 275?? a piece. They were the cheapest insulated doors that menards carries, and they were on sale. I don't remember for sure.
My torsion springs are extremely tight during my rewind. Are my springs in their relaxed state? What do I need to do to correct this if so? VERY FRUSTRATED !
Rollers are in the wrong hole (crucial for door breaking away from the jamb and following the pitch of vertical track). Horizontal angle is upside down (not a big issue). Cables should have been tightened and shaftline clamped off before the spring was wound (you are lucky that the door goes up evenly). Should have a strut on the top section for operator (an operator will crease the top section over time). However thank you for sharing your door installation with us.
How's everything going now? Do you still use those older 2 garage door openers? Or are they in the trash now?
That squeaking, is in part the plastic "reatainer".
But the reason is because is the torsion spring itself is too far stretched out...
Mark Mathews will having the spring stretched to far cause the fingers in the easy winders fingers to come out
do you mind telling me how much that door assembly cost?
Check your door first, don't just go cranking the force adjustments. Disconnect it from the operator and run it by hand. It should move smooth and freely and stay open at the halfway point. Hopefully your door isn't as loud as these things. Glad I don't install these debacles
excelent videos!, thanks for you help!
10:23 geshundheit!
turn the force up on your operater.
when the temp gets down around freezing (32 degrees) my garage door wont open byi tself. i have to get out and help it out a little. im thinking maybe the spring has stretched or loosened up since its 17 yyears old. before i tighten it ima sking if anybody knows if thatsth e problem or could it be something else???
Thanks man!!
for a 9 ft door you should have 9-3/4 turns on the spring
jescalese nope if it's the right Springs it's going to be 9round lame ass people that don't know s*** about doors
Safety 3rd
easy to listen to guy to Becuase safety is always 3rd..
Wow this guy is totally full of it lol. Tors Springs not unwinding cause they have too much tension?
looks like someones 3rd day on the job. they put the wrong spring on the door lol. rookie mistake
11 1/2 turns on a 7' door? Might get 3000 cycles on that spring. What a joke!
Hard hat safety first
Your counting the starting point you fool, that was one turn. Also a simple vice grip would have pinned the door down plenty enough
That was a rough watch overall lol
that door wouldn't fall no matter how little spring tension you had on it LMAO it runs like a bag of shit. Did you install that too?
Why don't we just use the damn drill motors to open the garage doors.duh
Stop giving advice
Don't trust this video.
Retry zYrZza
You are not a professional, please stop pretending to help. Furthermore you hold a hammer like a child. Please do not use hand tools for they are hazardous to your health (let alone power tools!)
This is a prime example of what's wrong with the internet. DO NOT WATCH!
Brad Maluta that is hilarious dude I completely agree I'm a master overhead Tech and this guy is a total moron what a girl
Brad Maluta y
Brad Maluta said