How To Replace A Snowblower Starter Gear W/O Specialized Tools
Вставка
- Опубліковано 16 січ 2020
- amzn.to/361V9Va Tecumseh Starter Gear Kit
amzn.to/2Tx6dH0 Tecumseh Starter Replacement
amzn.to/2uS1F3J Starter Gear Removal Kit
In this video, I show you how to replace a Tecumseh starter gear that is stripped without using any specialized tools. Keep track of your parts and make sure you wear safety glasses.
Help support Doublewide6 Repairs LLC by sponsoring his Patreon Account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.
amzn.to/361V9Va Tecumseh Starter Gear Kit
amzn.to/2Tx6dH0 Tecumseh Starter Replacement
amzn.to/2uS1F3J Starter Gear Removal Kit
the chisel worked way better than a screw driver. i also used a flap visegrip to get the ring back on. worked great! thanks for the video!
Best part of being a mechanic is making it happen with out special tools
Every thing is possible
I cover the shaft with a plastic bag ( to prevent the clip to fly off) then, to re-install, I use a socket and push on it by hand. Perfect comes with practice. Your method works fine too.
The ring faces away from the spring such that the opening/lip faces the end of the shaft. When released, it covers the retaining ring.
I noticed that too. The lip on the ring acts as a retainer for the clip, so it can’t spread open and come off the end of the shaft.
The best way to put on those clips is to have someone else do it. I hate those little buggers. But you did a great job with the gear replacement. Thanks for the video and the education.
If you listen carefully, you can get the clip land on the floor. Love those vids man!
Nice fix, I said a lot bad words trying to replace those rings. Thanks for the video's.
Good to see another video Bob. Those little c clips can be a pain to deal with I have lost more than one in my time. LOL Hope everyone in the family is doing well. Wishing you and the family a healthy and prosperous 2020 Buddy!!!
Good video. Now to see if my starter motor gear needs replacing, and if I can do it without the special tool. I'm sick of pull starting my snow blower every snowfall.
Nice fix Bob tricky job well done.
Im going to a starter shop in Regina tomorrow, get them to sell me or order me a new bendix gear. My gear teeth tore off because the starter was juuust a weee bit loose on those two TOPSIDE hold down screws. Ill putter together with locktite. I'll rub anti sieze on the axles whiles im in the area as well. Thank you for this tutorial.
Great video! keep them coming
Thanks for the tip sir. Be safe. Peace.🇺🇸
Those rings are a PITA!!
I found putting duct tape during removal and installation of clip on starter helpful. It keeps the clip from flying off and unable to find.
Oh the old c clip.. the vain of my life lol great video bob.. hope all is well mate
Nice job
wow thanks bob ... now if you only come fix my snowblower it would be great .. still surges and a new carb just like the old carb .. have a good weekend .. †
Govener issue, causing the surging? What did you end up doing?
Would it fall within reason to change out the C-ring for a snap ring instead to make future fixed easier?
You put the ring that sits on top of the spring upside down.
Do you have pliers to replace avil rings on impack tools
Works great
At the end of vid the top ring slides up over the C-clip to capture it on the shaft
yes, I noticed it when I edited. I'm on it. Thanks
Those motors are way under $100 on Amazon. Ya ya...I know ya get what ya pay for. BUT if you don't burn em out by holding down the start button they'll last.
Thanks, pretty good video.
The ring is upside down .