I built this fairly easy, and I can tell it works flawllesly, I only changed 1.5k resistor parallel to potentiometer with 2.2k for more precise temp selection but it is not necessary. I pluged it to ATX power suply to 18V (plus terminal to +5V(red wire) and minus terminal to -12V(blue wire)). Max current draw is about 2.8A, and it heats up from cold to 370 C in 35 sec. I have 6 soldering irons(four stations) and this is the best and costs less than 5$(ebay handle 3$, rest of components about 2$ on Tayda). Well done my friend.
Merhaba, bu kiti breadbord üzerinde 10,5 volt kızdırma bujisi ile bir sever çalıştırmıştım. Daha sonra oluşturduğum devrede çalıştıramadım. Neden olabilir? Fikrinizi öğrenebilir miyim. Sensör olmadan çalışmaz mı?
The last one you created, I had tried both versions and both worked Great! I can not wait to do this one also. You come up with the easiest way to make these project! Keep up the Good Work! Your the master at these with the Thermistors(907F) versions, would be awesome if your next project you make one for the thermocouple(907A) Versions.
Looks good. I would have just used regular wire, but then I suppose you could say it is kind of like have a pcb board with chunky traces. But hey, as long as it works. The only problem with some like this is you need another soldering iron to create this one. But, I might give this a try.
I executed the circuit exactly, and when connected to more than 4 volts, I found one of the resistors connected to the variable resistance, and its value 2.2 got hot and burned.. I checked the whole circuit and I don't know why
appreciable work ....but there is some quarry i have , you are using 1pcs LM358 ic and there is 2pcs LM358 ic in your linked schematic diagram image and that design is not working please give right schematic please .............
Hi. I am not sure my circuit can work with your pen but my circuit can work good with any pen have 30_50 ohm of sensor inside Pen. Please check your pen
Merhaba, çok faydalı bir proje. Pu kiti breadbord üzerinde 10,5 volt kızdırma bujisi ile çalıştırmıştım. Daha sonra oluşturduğum devrede çalıştıramadım. Neden olabilir? Fikrinizi öğrenebilir miyim. Sensör olmadan çalışmaz mı?
Hello sir, please can you create a video on overheating protection like the one in the rework stations using 2200 watt element core, type k thermocouple in the heating core, relay and lm358. I want a video of the above-listed element and how to use them to create overheating protection
Soldering iron heat hota ha lakin ya circuit temperature control ni kar rha main is ka sath 24v 3amp ka laptop ka charger use kar rha hu ap kuch bta sakta hain please reply
Hola . la imagen inicial y la del minuto 2:56 no coincide . Fue modificado ? porque no se aclara Ver F 14 F15 y F 16 va a masa o no . El Lm 358 no tiene conexión a masa desde el terminal 4 . Lo he revisado y tampoco pude hacer funcionar el led de estado no titila, y hay valores de resistores diferentes como 1.9 K en lugar de 1.5 k
Esto es un enrredo, estoy igual, no titila el LED, enciende de una vez, no regula con el potenciómetro, tres veces he realizado el proyecto y no logro hacerlo funcionar.
how can i help you when you don"t know about you soldering ? We have a lot of soldering and my circuit can work only with soldering handle with a1321 thermal
@@mastiyoforever7836 tip nya 24v 60W, lebih ideal pake dibawah 24v biar awet elemen nya, bisa pake 12v sampe 20v maksimal. Ideal pake 19 atau 20v dari charger laptop. Kalo cuma pake 12v proses panas nya lambat.
I am just asking This circuit, can work with a A1322 heating element having 13-15 ohm heater resistance and 1-2 ohm sensor resistance, is this safe to use 24v 4amp dc power supply with this element.
I built this fairly easy, and I can tell it works flawllesly, I only changed 1.5k resistor parallel to potentiometer with 2.2k for more precise temp selection but it is not necessary. I pluged it to ATX power suply to 18V (plus terminal to +5V(red wire) and minus terminal to -12V(blue wire)). Max current draw is about 2.8A, and it heats up from cold to 370 C in 35 sec. I have 6 soldering irons(four stations) and this is the best and costs less than 5$(ebay handle 3$, rest of components about 2$ on Tayda). Well done my friend.
That is good for hear my friends
sorry you can send me the schematic of the welding station that you did
Merhaba, bu kiti breadbord üzerinde 10,5 volt kızdırma bujisi ile bir sever çalıştırmıştım. Daha sonra oluşturduğum devrede çalıştıramadım. Neden olabilir? Fikrinizi öğrenebilir miyim. Sensör olmadan çalışmaz mı?
Hello, You there? It'll be great if you help me.
Hi Guy today we make Diy Soldering Station on Hole Board. The Schematic on description. Thanks
kênh này mở khi nào z a?
The circuit diagram is not clear.
The last one you created, I had tried both versions and both worked Great! I can not wait to do this one also. You come up with the easiest way to make these project! Keep up the Good Work!
Your the master at these with the Thermistors(907F) versions, would be awesome if your next project you make one for the thermocouple(907A) Versions.
+njfulwider5 thanks you very much
Looks good. I would have just used regular wire, but then I suppose you could say it is kind of like have a pcb board with chunky traces. But hey, as long as it works. The only problem with some like this is you need another soldering iron to create this one. But, I might give this a try.
The schematic a.top4top.io/p_1794st6by0.png
its did work and it only draw 1.4 amps , heat sink is not even heating up fast ,thnx bro
you are welcome
Very weldone bro 5 thumbsup for u
I executed the circuit exactly, and when connected to more than 4 volts, I found one of the resistors connected to the variable resistance, and its value 2.2 got hot and burned.. I checked the whole circuit and I don't know why
Hi sar good work
What is power of soldering station
Can we change mosfet with triac and supply solder from 220v bruh ?? And lm358 using 12v for driving triac we use optocouopler 3021?
Yes. It OK
Ok thankyou v.m
muốn gắn thêm arduino để đọc nhiệt độ thì ntn ạ
appreciable work ....but there is some quarry i have ,
you are using 1pcs LM358 ic and there is 2pcs LM358 ic in your linked schematic diagram image and that design is not working please give right schematic please .............
LOL. Google datasheet of LM358 and you will understand.
Hi, is it possible to use a Hakko FX-8301 pen instead? Btw, do you have Hakkp FX-8301 pinout? Regards. 73, PU2PLL - Brazil
Hi. I am not sure my circuit can work with your pen but my circuit can work good with any pen have 30_50 ohm of sensor inside Pen. Please check your pen
Good
Excellent show but for the love of the gods, please kill the music.
Kindly If you could tell is this board support thermistor based solder iron like chinese Kada ............
what are the components you used in this project no body knows. better to explain with soldering in pcb as well.
Nguồn của em 24->26 vôn dc có chạy được không anh hay chỉ có 19 vôn mới chạy được ạ. Em cảm ơn
Hi,you are great at this,can i use this for a 5wir hot air gun?
Merhaba, çok faydalı bir proje. Pu kiti breadbord üzerinde 10,5 volt kızdırma bujisi ile çalıştırmıştım. Daha sonra oluşturduğum devrede çalıştıramadım. Neden olabilir? Fikrinizi öğrenebilir miyim. Sensör olmadan çalışmaz mı?
what is the maximum temperature, sir?
What model of hakko soldering iron did you use? Thank you very much :)
Hakko 907 with sensor a1321
Thank you very much
@@LongTechnical is it possible to use a 936 soldering iron whose sensor is 1322?
is it possible to use a soldering iron on T12 stings with this circuit?
T12 use different circuit
is good
thanks
thermocouple iron or thermistor?A1322 or A1321?
can i use 15 ohm heater and 3.4 ohm sensor on this circuit
Hello, can I replace the LM358 with a LM393N?
hi.. great job
could you share the pcb lay out please..
in my circuit the current needed is 9 to 10 amperes, is there something wrong? or is there an effect from the solder handle that I use? I use type 936
คุณต้องเปลี่ยนไส้เซรามิคของด้ามจับ
Maybe in the next ,,,u can custom this with digital volmeter for realtime temperature bruh from lm358 non inverting thnks
Mạch này hoạt động trong khoảng bao nhiêu vôn vậy anh
can you use lm356 soldering temperature?
Can I use it with DC 12v iron???
i can.t find irf540 how i can get it
hlo sir
I have lk 936 soldering iron
i wanw auto sleep mode have you any idea
Hello sir, please can you create a video on overheating protection like the one in the rework stations using 2200 watt element core, type k thermocouple in the heating core, relay and lm358. I want a video of the above-listed element and how to use them to create overheating protection
Ye clip kuch smjhane k liye hai ya apne aap ko hoshiyar dikhane k liye hai.... No diagram dirct work without information
Bro can you tell me the changes I have to make if I want to use it with a 220v soldering iron.
Nice
can we add different suplay,,,12vdc for operate lm358 and use 24vdc for operate the soldering iron like gordak or hakko element?
Yes of course
@@LongTechnical but how about grounding, can we use 1 ground line but 2 vcc 12 & 24 or use buck converter
Yes. 1 ground line for both
@@LongTechnical ok tthanks your answer very helpful
I hope you reply to my comment. I want to ask, what is the VCC voltage in the schematic? And can the ic be replaced with a jrc 4558?
VCC power + supply. You can use Lm358
Aap se request hai ki aap sabhi part ke detail de
this circuit can work with KADA handle
Station components I have only handle as u info I will look in Amazon.
look on amazone you can buy the best handle
I did the same job plus the iron has no control
Can i Use Gordak 936 Handle..?
Soldering iron heat hota ha lakin ya circuit temperature control ni kar rha main is ka sath 24v 3amp ka laptop ka charger use kar rha hu ap kuch bta sakta hain please reply
you waste a lot of solder dude😎
so true dude. solder is so expensive.
Many of this persons videos lack clarity and credibility.
Hola . la imagen inicial y la del minuto 2:56 no coincide . Fue modificado ? porque no se aclara Ver F 14 F15 y F 16 va a masa o no . El Lm 358 no tiene conexión a masa desde el terminal 4 . Lo he revisado y tampoco pude hacer funcionar el led de estado no titila, y hay valores de resistores diferentes como 1.9 K en lugar de 1.5 k
Esto es un enrredo, estoy igual, no titila el LED, enciende de una vez, no regula con el potenciómetro, tres veces he realizado el proyecto y no logro hacerlo funcionar.
Nice. Where can I get Hakko handle at good price and original one.
amazone or bestbuy man
I need another model for My yaxun 1 ohm sensor.
Está muy bueno. Pero no pones diagrama?
what is the use of lm 358 here
Comparator, i think
What Is the 5th wire plz tell
The schematic cant open
Hello sir thanks for information. But can you send me diagram of this circuit.
can anyone tell what type of temporature sensor it supports thermoresistor or thermocouple?
a1321 sensor
Will 18v 2a work
Is this schematic for the handle with 50 ohm termoresistor?
Yes. It works with 50 ohm termoresistor
Hi , can i use Gordak 952 Handle?
tanx
Link schematik not working sir,give me schematik!
Hi , can i use Gordak 952 Handle?
what size is the watt resistor, sir???
Hello master my heater is a1321 can i use ur board
yes
I can’t see the diagram please help me find the diagram
War is the circuit diagram in this video
Output range..?
I make it but didnot work make as say but heat is not controling my soldring iron gos to hot and melt wat should i do plz reply master
what is your soldering handle ? Hakko 907 ? What is the type of thermal ? A1321 ?
I dont know i forgot its name is vaneshd
how can i help you when you don"t know about you soldering ? We have a lot of soldering and my circuit can work only with soldering handle with a1321 thermal
Where is temperature readings??
Ok master i will try to find itout any other way to find heater number i have clone
Hi my frinde I can't download Chart
Hello, PCB please?
I can give 24 volt DC
I made solder using lm358 non inverting, btw can i use 24v for vcc lm358 or only max 15v for operate lm358??
Apakah ini berhasil om?
@@kadekastraantara4400 work, ternyatternyata lm358 tu max bisa pake 32Vdc, kalo power nx dual, max 16vdc dan -16vdc kalo ditotal juga 32v😂
@@TheFandiahmad mantap om.
Apakah pakai power suplay 24v dc bisa ap harus di bawah 24v dc??
@@mastiyoforever7836 tip nya 24v 60W, lebih ideal pake dibawah 24v biar awet elemen nya, bisa pake 12v sampe 20v maksimal. Ideal pake 19 atau 20v dari charger laptop. Kalo cuma pake 12v proses panas nya lambat.
Can I enter the 24 volts dc voltage?
yes
Friend, have you updated the a1321 sensor's circuit information? Do you know the site I can learn?
Google search
Long Technical thanks
Can I use capacitor 100uf 35v?
is this thing will work with 24v , 3A or not?
yes
अपने लिये बना रहा है तो क्यों दुसरो को दिखा रहा hai
How to make jlcpcb download ?
T12
bos minta layout ada gk
Hi
Diagram pliz
no me funciono no gradua ni calienta la punta t12
No es para T12 el cautín es más antiguo
1322 Not Working 😢
1322 heater ohm 15 sensor ohm 1.2 ohm ....my 1322 element
kada 2018d barns on this project ....
sir plz 0 se 24 volt ka peoper regulatar banae ok saman vi
+jagdeep jagdeep sharma from 12 to 19.5 VDC max
In schematic diagram u used two IC LM 358 but in video u used only one IC!!
+electronics & Fun In schematic has only one ic lm358. Did you try to know about lm358 before comment ?
LM 358 is two ic operational amplifier in one case. two in one.
I am just asking This circuit, can work with a A1322 heating element having 13-15 ohm heater resistance and 1-2 ohm sensor resistance, is this safe to use 24v 4amp dc power supply with this element.
This circuit can only work with 30 -50 ohm sensor resistor. For your sensor find another circuit in my channel i have video for that
Tomorrow i will send to you. now i am busy
Where is the video??
Sir i want to add a display also in this can u tell how to do so
I want the screen to display the temp of the iron
I have made it but it does nothing
Do again
अपने लिये बना रहा है तो क्यों दुसरो को दिखा रहा hai