O que acho mais legal nestes vídeos é a solução que eles apresentam para usar como gabinete ou caixa de montegem para o projeto eletrônico. Muito legal mesmo, parabéns.
Awesome work I love the way you utilise drainage pipe I’m going to build a power supply using the same method learn a lot from this channel thank you and a big hi from the UK keep up the good work and stay safe
Just warning you guys that are actually going to build this, the power regulator has no short/ovrtload protection, in a event of a short circuit if the power source can provide more than 10amps, it will blow up. Might be smarter to use say 24v 5A supply so instead of max output beeing 12v it will be 24 and the risk of blowing your regulator will be greatly reduced. datasheet says maximum continious current of the regulator ic is 9A but in my expirience it overheats, so might be smart to add active cooling or keep it at 5A max.
@@mujtaba2617 Since the regulator is designed for 9A max, I would reccomend using an 5A fuse because if you are familiar with fuse caracteristiscs, even if you fraw duble the current trough the fuse it may not blow instantly, this solution is not great because it is still not garanteed to save you regulator and the fuse might blow while using the regulator at say 8A, but it is still better than no protection.
I have one question regarding Digital VOLT AMMETER connection. Among the 3 thin wires yellow goes to positive output. And red goes to buck converts(300w) output + terminal. But what about black wire? Which is the correct seen many videos all have different. 1) Not connected 2) connected to buck converters output negative. 3) added LM7812 at buck converters o/p and given safely 12v to power up the digital V/A meter. As per me the 3rd ne should be correct but all of above cases are working... Pls help me.
Bro it is not a constant current (cc) mode its current limiting mode which can drop voltage at selected current value when load current reach at selected value
Quite simple (case especially), but you don't need to connect thin black wire from VA meter if all the components are powered up by same SMPS. And you can connect VA meter power cables directly to free screws on SMPS, not to input sockets of converter.
Can you do this with 24v 16 amp power supply but get the range to go from 3v to 58.4v? What would I need? I relies I wouldn't get but 5-6 amps at higher voltage if it's possible at all
yes you made it but you did not show where each wire went and why with a child's picture drawing anyone could have done the same ( your not good for teaching )
Sjsjdjrjrjru I think 💬 a question 😂 I can get it now but I think it's the day today so I'm going to get it done before then I'll go to work I can 🙂 a good day for letting me and get it done before then I can 🙂 a good 👍 I have a question about this one 🕐 I think it's a good 👍 a question ❓ I have to go back for a little while and I think I think
Thanks!
You are perfect power supply
Thanks
Молодец!!! Все супер!!!,, ЛАЙК,, и подписка. Привет из России.
Good video🎥🎥🎥
Thanks
Mantap 👍👍 Semangat terus 💪💪
Thank u dada..Finally the video is here...
Yes
Nice Power Sapply Bro 👌♥️♥️♥️
Thanks
Thanks Bro ♥️♥️♥️
O que acho mais legal nestes vídeos é a solução que eles apresentam para usar como gabinete ou caixa de montegem para o projeto eletrônico. Muito legal mesmo, parabéns.
Awesome video🇧🇷😉👍 love❤ very cool 👏👏👏👏👏👏 thanks you bro ( subscribed)
Nice 👍👍
Thanks
Nice project ❤
Clearly defined step by step design process, awesome 👌 👏 Hope for some more out from you, Best wishes
Please subscribe my new channel
bit.ly/3sBkYbK
@@easytechzones 😂😂😂😂
Where did you buy this plastic box?
Hnnfnfnv 👌👏
Love from west bengal ❤❤❤👍👍👍
Thanks
Awesome work..
Your all project are fabulous 👍👍👍
Thanks
Your all videos are really awesome and useful.🤗
Thanks
Awesome work I love the way you utilise drainage pipe I’m going to build a power supply using the same method learn a lot from this channel thank you and a big hi from the UK keep up the good work and stay safe
You doing super good.
Thanks
nice job!
Thanks!
The DIY multiturn pot is fabulous...👍👍🔥🔥
Thanks
How was the multi pot made
Does it have output short circuit protection??
No
@@easytechzones Ouch
@@thxepsilon8292 pretty bad IMO. proves to me he is not really knowledgable
@@kennmossman8701 It seems to be a basic safety issue, among other things. I guess he doesn't care.
@@kennmossman8701 I would not feel safe with such a piece of equipment in a lab, would you?
Awesome 🤩
Thanks
@@easytechzones welcome broo😍
Valo laglo dada 😀😀
Thanks
Süper elinize sağlık özellikle kutu tasarımı harika💯💯💯
Which super glue u use?
Favicol wudfil
is there short circuit protection? since the buck-boost module doesn't have short circuit protection.
The buck converter have sort circuit protection
good job man ❤️
Thanks 🔥
Can I have the names of the songs used on this video ?
Just warning you guys that are actually going to build this, the power regulator has no short/ovrtload protection, in a event of a short circuit if the power source can provide more than 10amps, it will blow up. Might be smarter to use say 24v 5A supply so instead of max output beeing 12v it will be 24 and the risk of blowing your regulator will be greatly reduced. datasheet says maximum continious current of the regulator ic is 9A but in my expirience it overheats, so might be smart to add active cooling or keep it at 5A max.
i am building the same project i have but 24V 10A SMPS instead of 12V one should i use different components?
@@AkashJadhavIT no need, just don't overload it
@@filenotfound__3871 what if we add a 10A or 12A fuse somewhere before the regulator? would it be safe?
@@mujtaba2617 Since the regulator is designed for 9A max, I would reccomend using an 5A fuse because if you are familiar with fuse caracteristiscs, even if you fraw duble the current trough the fuse it may not blow instantly, this solution is not great because it is still not garanteed to save you regulator and the fuse might blow while using the regulator at say 8A, but it is still better than no protection.
@@mujtaba2617 IME the circuit goes before the fuse. else the fuse 'pops' all the time
Yeah glue everything down so when you have to repair something you're fucked! 😂
Bro i have 33A 12v smps can i do with that?
Yes but ammeter can control only 10amp
Thank you
Useful video
Nice
Konsa potential metar hai sir kaha milega sir
How much amp this 12v smps have??
Hello Sir, I am building the same Project i have 24V 10A SMPS, should i use different components as in 'buck covertor' if so which one?
you never got an answer because the guy is a clown
Can I use an old computer PSU?
Bhai please use the original pots otherwise value and amp may differ
Used original trimpot which was inbuilt in board
Mcglhmmgkfnekrkr6273
If you list down the item you use in your description , it will be very useful bro
Ok
his descriptions are sometimes WRONG, so good luck with that
How are you supposed to service the power supply with the case being bonded together with glue.
Can you make an adjustable power supply connected on a power supply of 12v. Symply. Thank you.
I have one question regarding Digital VOLT AMMETER connection. Among the 3 thin wires yellow goes to positive output. And red goes to buck converts(300w) output + terminal. But what about black wire?
Which is the correct seen many videos all have different.
1) Not connected
2) connected to buck converters output negative.
3) added LM7812 at buck converters o/p and given safely 12v to power up the digital V/A meter.
As per me the 3rd ne should be correct but all of above cases are working... Pls help me.
What is the value of wire wound potentiometer meter and the wattage ?
Max to max 35 inr
I mean what is the resistance value and wattage. I can't understand the wiring of potentiometer.
@@udaybhanumoharana6217 10k according to original ones. I've used pots 3590S in my bench PSU (35V, 7A).
Bagus
Muy bien gracias
Thanks
nice
Obrigado novamente.. top demais.
can use a 36v 5a power supply?
Bel lavoro, pero' l' interrutore potevi metterlo davanti visto che potevi scegliere.
Bro it is not a constant current (cc) mode its current limiting mode which can drop voltage at selected current value when load current reach at selected value
Ok
LMAO he does not know the difference
It does the same thing..
Link project????
Quite simple (case especially), but you don't need to connect thin black wire from VA meter if all the components are powered up by same SMPS. And you can connect VA meter power cables directly to free screws on SMPS, not to input sockets of converter.
Lm723 linear dc dc power supply vs xl4016 buck converter power supply.
Which one is best, please share your honest reply.
Can you do this with 24v 16 amp power supply but get the range to go from 3v to 58.4v? What would I need? I relies I wouldn't get but 5-6 amps at higher voltage if it's possible at all
Fast like 🥰
Thanks
Sir kitne compnent lag rahe hai niche ditls me de diya Karo buying Link ke sath PVC pipe konsa Lena chahiye sir please send me the details catalog
Potentiometer in video is not multiturn, but at the end we see multiturn rotation )))
This is custom low cost multi turn pot. Check previous video
Where did you buy this plastic box?
It is made from PVC pipe (10cm in diameter).
Can i use 36 volt 2.5 amp smps with this buck convertor
Yes, it supports up to 40V input voltage.
friend can you make for me how much for that
In this system, can't we first increase the voltage and then adjust it with a step-down reducer?
but I mean how many K can I put the potentiometers, the source is 90W, 19V 4.5A
como hacer grabar mesa de trabajo
No cooling fan, No heat sink . Is this safe ?
Bang boleh minta skema nya
Video ato deri kno holo?
Amr channel hack hoye gechilo
Sir mera variable power supply motor lagane ka bad 12.3 volt se uper nahi ho raha hai
Explain about materials
Good bro
BUEN PROYECTO 👍, PERO FALTA LOS ENLACES DE LOS PRODUCTOS QUE UTILIZAS. 😔😔
yes you made it but you did not show where each wire went and why with a child's picture drawing anyone could have done the same ( your not good for teaching )
I call it a "Look Mommy at what I did" video
this more of a assemble it yourself video. otherwise its a good video
Please do giveaway of this variable power supply i need 1 for myself 🥺🥺
Oh
Anu guarantee.. That you win it on giveaway?
I ❤️ sir
আমি কলকাতার আসে পাশে থাকি। আপনি এইরকম আমাকে একটা বানিয়ে দিন কতো খরচ পড়বে বলুন অ্যাডভান্স দিয়ে দেবো but নেবো sure
Akta new banabo bech power supply.
@@easytechzones okkk waiting for that😄
Bro, what line to connect if me add a speaker or short protection?
3 pin led Nikola bul Gaya dost....
You are a power supply 10 Ampere yes
yes
just use 2 clamps in reverse mode to push the 2 wood blocks out and do the abs tube to box conversion :)
i have also made it .go and watch
Can I share u a 20a buck converter please make a video of that
Wow
Please replay
Sjsjdjrjrjru I think 💬 a question 😂 I can get it now but I think it's the day today so I'm going to get it done before then I'll go to work I can 🙂 a good day for letting me and get it done before then I can 🙂 a good 👍 I have a question about this one 🕐 I think it's a good 👍 a question ❓ I have to go back for a little while and I think I think
You are duplicated by "samar experiment" youtube chanale
बनाने गरज नहि रहे महाकाल
এই পাওয়ার লগবে
DUDE! LEARN HOW TO SOLDER FFS!
Copy of technical IND
This video was uploaded on 7 feb 2022 and technical ind channel, power supply video was uploaded on 10 mar 2022. Who copied? Reply me
@@easytechzonesyes. Right ❤️❤️
No voice how to assemble
this is the worst build ive seen so far