I rented the unit. Never drilled before except with a hammer drill. Drilled 6 6” holes in no time and exactly where I wanted. Short learning curve, feels safe to use especially when you discover the clutch kicks in smoothly and at manageable load. I would let my wife use it.
This machine is the best drill that I have to use.On has acquired 1 and frankly it is the top of the top .1 carrot of 25cm in 10min. There's nothing better. Thanks to allemends and bravo to the Americans for the system.
you didn't show, , bad camera shot, when cutting down, Wont the hole rig just drop once it penetrates the other side smashing it into the upper surface of the surface you just cut? if the operator was not expecting it to penetrate at that moment, if they are holding on to the rig, depending of the weight of the core of course, could they not do some serious harm to their back when it drops, pulling them down suddenly with the rig ? other than that, it is a great looking tool.
Well you fucked then.... What I would do I re attache a smaller core than the inside diameter and drill a ll the way through then use a chissle to remove the thin layer or cement around the inner surface of the broken cutter. At this point you weld a puller to the broken coring tool and pull. Then finish the job. But in all likelihood the tube of the cutter is far less likely than the union between the tube and the shaft it connects to. ps in really high at the moment so I could be talking shit.
Привет из солнечного Сочи! Я сверлю китайским установками. Есть ручная дрель, можно снять приклад, и протиснуться с коронкой в узком месте. Но большая установка на станине всё равно быстрее. Одна установка DongCheng Z1Z ff2-250 проработала полтора года, и ещё на ходу. Сразу подшипники поменял на хорошие. Ну и вторую новую такую же купил.
That's a really nice set up👍but if you're just drilling here and there great! But if you're drilling in/for commercial buildings it's not efficient! 25+years experience here! I've done 10,000 holes just in one building(jersey city) I've always used diamond tech industries(DTI) motors for quantity&quality with diamond bits💯 best thing is they are easy to repair/replace if you burn them out🙏🏼
You need a splash guard wet dry vacuum accessory to contain over flow of the water. That's always a challenge when ever we core in existing spaces with carpets n stuff. It can really complicates things.
Looks nice and all but i would go insane if i had to use both hands the entire time. And what happens with the set-up when you drill a hole in the floor but don't know the thickness and go through unexpected?
A salesmen pitched this to the company my brother and i worked for, As he was drilling he broke the core of before it was all the way through. He asked the sales guy what now and that was the end of it. This a cool system but its dependent on the anchor completly, It's common for cores to break due to mooning rebar or cutting tie wire and getting jammed up.
still can be a great for tight space and up high i think. one time it take us 2 guys several hour to set up a core drill. we have to take the drill apart and assembly them back together up high 10 ft in the tight spot in the ceiling.
I wouldn't drill them too deep and remove the excess wood with an SDS bit sharpened to a chisel, mounted on a rotary hammer drill. I would plug the hole with a circular cap hammered into it, with an appropriately sized hole for the birds.
A Metabo mill and a simple metal converter with a single $ 4,200 bit do not seem too expensive, although it has become easier to increase the price. This is not fair.
I cannot get into the idea of a Angle Grinder running this bore. The adapter would have to have insane gear reductions. Although I do see a Metabo Grinder being used. That is definately a plus.
QUIERO SABER SI HACE MUCHO RUIDO, TODO CASO, EXISTE UN EQUIPO QUE NO HAGA RUIDO? , I WANT TO KNOW IF IT MAKES A LOT OF NOISE, IN ANY CASE, IS THERE A EQUIPMENT THAT DOES NOT MAKE NOISE?
It seems this system could lack in torque compared to others due to being angle driven. I get the concept and that it has a better clearing radius.. But I am very curious to see how this system would hold up in really bad binding.
This is very smart way to drill concrete,Can you send me tools list please? I just subscribe your channel , all the time I have to use heavy rotary hammer .
Metabo proudly produces all high end products here in Germany. They do their own development, casting, injection molding, and motor winding. They also assemble their products here. Please inform yourself before posting. Greets from Germany ;)
Xavier Ancarno not really after pumping concrete for many years they add stuff into the concrete that will slow the bit cover the diamonds and eventually lock up the bit it's in the concrete mix most modern banks have shredded Steel along with ball bearings and rebar all around
This is just great.
Rare to see well thought out tools nowadays.
I rented the unit. Never drilled before except with a hammer drill.
Drilled 6 6” holes in no time and exactly where I wanted. Short learning curve, feels safe to use especially when you discover the clutch kicks in smoothly and at manageable load. I would let my wife use it.
Awesome!
Yeah I had an electric jackhammer on a job then the lady that was manager there got excited and asked if she could borrow it.
This machine is the best drill that I have to use.On has acquired 1 and frankly it is the top of the top .1 carrot of 25cm in 10min. There's nothing better. Thanks to allemends and bravo to the Americans for the system.
Glad you enjoy the system!
This was the coolest video I've seen all day!
what a beautiful invention. awesome tool.
Thanks!
you didn't show, , bad camera shot, when cutting down, Wont the hole rig just drop once it penetrates the other side smashing it into the upper surface of the surface you just cut? if the operator was not expecting it to penetrate at that moment, if they are holding on to the rig, depending of the weight of the core of course, could they not do some serious harm to their back when it drops, pulling them down suddenly with the rig ? other than that, it is a great looking tool.
What happens if the core snaps after the anchor depth, and before you’re through the slab?
Well you fucked then.... What I would do I re attache a smaller core than the inside diameter and drill a ll the way through then use a chissle to remove the thin layer or cement around the inner surface of the broken cutter. At this point you weld a puller to the broken coring tool and pull. Then finish the job.
But in all likelihood the tube of the cutter is far less likely than the union between the tube and the shaft it connects to.
ps in really high at the moment so I could be talking shit.
@@africanelectron751 should just stick with the offset rig and anchor bolt, if it ain’t broke don’t fix it 👍
Отличная,и необходимая технология! Суппер парни придумали! Успехов в работе! Привет из России!!!
Когда попадут на полумесяц(произойдёт клин коронки), этот парень останется без руки! И с переломанными ногами) 100 % .
@@CGM-86 есть такое опасение.Успехов
Привет из солнечного Сочи!
Я сверлю китайским установками.
Есть ручная дрель, можно снять приклад, и протиснуться с коронкой в узком месте.
Но большая установка на станине всё равно быстрее.
Одна установка DongCheng Z1Z ff2-250 проработала полтора года, и ещё на ходу.
Сразу подшипники поменял на хорошие.
Ну и вторую новую такую же купил.
Jeez this things helps me at my job site all the time
That's a really nice set up👍but if you're just drilling here and there great! But if you're drilling in/for commercial buildings it's not efficient! 25+years experience here! I've done 10,000 holes just in one building(jersey city) I've always used diamond tech industries(DTI) motors for quantity&quality with diamond bits💯 best thing is they are easy to repair/replace if you burn them out🙏🏼
LOVE TO HEAR FROM ALL THE WEEKEND WARRIORS WHO KNOW IT ALL !
You need a splash guard wet dry vacuum accessory to contain over flow of the water. That's always a challenge when ever we core in existing spaces with carpets n stuff. It can really complicates things.
We sell Kor-It slurry rings that are very helpful.
Need a second technician to operate a wet vac, and suck up all the water.
Great video folks!
I'm good with the Hilti core drill I use. The anti-jam clutch isn't a new thing, been around for quite some time
I got to get me one once I clean up the shop and organize things better I’ll have space.
It's nice. The biggest problem I see is the bit. This means all companies have to change all their bits
Less dust..great system
I wonder if I can modify my Harbor Freight oscillating tool to do the same thing.
4:12 A shielding to reduce the splatter would make it perfect.
There are slurry rings available to help.
@@USSAWS sir tell me pleas .from where i buy core ez system. Really i need it.
@@USSAWS i am from india and here is not available.
Looks nice and all but i would go insane if i had to use both hands the entire time.
And what happens with the set-up when you drill a hole in the floor but don't know the thickness and go through unexpected?
Give us a call 866-987-7297 and we can walk you through any concern!
@@USSAWS Thanks for the offer but i think i'll stick to my Hilti set-up :P
@@likilikiki They have a great set up as well!
Thats very good machine.
Whats name of all part this machine?
Nice
Pliss call me 00966559074251
@@nadeembajwa4482 you can give us a call at 866-987-7297 or e-mail us at sales@ussaws for more information
How do you go about cracked cores?
Very good this video
German power tools are simply the best, even in the US :-D
German power - where is, it is the sound was gone, song of this times is Alahu achbar. Germany is lost
Hello I am from India, how can I purchase, Please guide
А если керн сломался, что делать? И анкер уже не держит
I want this its work IN Stone also?
Where i get this machine...???
You can order it off of our website: www.ussaws.com/core-ez-core-drilling-machine
I want to have a set. Is it available? How can I contact you to buy it
And if the jam remains, your fins will break or what is it like?
What if the core sample needs to be tested via compressor?
what is the maximum diameter available for core bit. please reply.
10"
I don't have a use for one of these, but I want one.
Well drilingi woter
How much is this fine tool a pretty penny I know
Link to purchase the Core EZ: www.ussaws.com/core-ez-core-drilling-machine it is priced at $2975.00
Can I get it down a liftshaft and make a hole big enough for me to climb through?
I got a call in middle of this video, and I had to say "sorry, im busy"
We don't monitor the site in that way. Sorry that you received a call for sales pitch.
@@USSAWS lol
@@drozcan lmao what a funny misunderstanding here.
A salesmen pitched this to the company my brother and i worked for, As he was drilling he broke the core of before it was all the way through. He asked the sales guy what now and that was the end of it. This a cool system but its dependent on the anchor completly, It's common for cores to break due to mooning rebar or cutting tie wire and getting jammed up.
still can be a great for tight space and up high i think. one time it take us 2 guys several hour to set up a core drill. we have to take the drill apart and assembly them back together up high 10 ft in the tight spot in the ceiling.
How do you set a guide post at an angle.. to use the core bit at an angle
Always wondered how core drilling was done.
Mesinnya sdh renopasi
I work in masonry.. this is a great tool to have
nice Machien
i am plumber works. i needs. How much price
Here is a link to the Core EZ: ussaws.com/product/core-ez-core-drilling-machine/
please send Online purchase link
www.ussaws.com/core-ez-core-drilling-machine
Hi,it's possible to buy in Europe?
No, it is only sold in the U.S.
Hi... Where I can find this core drilling machine in South Africa?
We only ship within the U.S., I am not sure this would be available in your area.
How do you know this is level or straight?
If the exact depth of a floor slab is not known. How do you stop the drill from over drilling?
just pull out pieces by pieces
Floor slabs are usually 3"-5"
Feedback or the lack of it will let you know you're done.
what happen if the core breaks while drilling? or the anchor came lose?
Was thing the same thing
This is so cool
HfzsxhsDdZffsgaFDFxjdjhsdsidausfjqhjihsuidwewgygwf vegghbz
Hzbdhsshgdgdddsfgggzsjzizdarkgsgidsjxzvvvvzzfzffsfzd. BzhHdhcffzvhgfdaf
Technology fantastic
Hai iska price kya hai yah mil sakta hai khareed sakte hain kahan per iski Bajar hai
A genuine question, how would this work with a cavity wall?
Very nice tool.
How much machine and how much one coring bit
All pricing is avaliable on our website: www.ussaws.com/water-works-division/u-s-saws-core-drilling
Could this be used for wood? I trying to find an easy way to make birdhouses in trees similar to a woodpecker :)
I wouldn't drill them too deep and remove the excess wood with an SDS bit sharpened to a chisel, mounted on a rotary hammer drill.
I would plug the hole with a circular cap hammered into it, with an appropriately sized hole for the birds.
2صضصذذضذذذذذشذصذذصذذصذضذذذذذذصذضصذسصضضذضذصذذذضشضضضشذذضضضضضضضضضضشذص
Wow very easy and safe to works
How should I get this product
visit our website www.ussaws.com or give us a call 866-987-7297
A Metabo mill and a simple metal converter with a single $ 4,200 bit do not seem too expensive, although it has become easier to increase the price. This is not fair.
It's more of a complex innovative system to why the price is higher, we also manufacture in the states. Sorry you feel this is over priced.
How many price with delivered in pakistan
We only ship inside of the U.S.
But where is the purchase bro
Which brand is this machine and I want how much price
It is a U.S.SAWS brand and it is powered by Metabo. The price is $2975.00
www.ussaws.com/index.php/core-ez-core-drilling-machine
I cannot get into the idea of a Angle Grinder running this bore. The adapter would have to have insane gear reductions. Although I do see a Metabo Grinder being used. That is definately a plus.
QUIERO SABER SI HACE MUCHO RUIDO, TODO CASO, EXISTE UN EQUIPO QUE NO HAGA RUIDO? , I WANT TO KNOW IF IT MAKES A LOT OF NOISE, IN ANY CASE, IS THERE A EQUIPMENT THAT DOES NOT MAKE NOISE?
4:08 So, is that crack going to be a problem?
I think its water
Yes it's water
03 year Experience Concrete core cutting machine operator .Which site does concrete core cutting jobs take? i need job
Good afternoon. what tool is it from Argentina ALQUIMAX Rental
This is a great coring system
Good job
SIR WHAT WATER USE MUST PLZ REPLYY AND PRICE
The price is $2975.00
www.ussaws.com/index.php/core-ez-core-drilling-machine
It seems this system could lack in torque compared to others due to being angle driven. I get the concept and that it has a better clearing radius.. But I am very curious to see how this system would hold up in really bad binding.
Can i use my bits that i already have with it?
No, we have specialized bits for the machine.
the new Payday DLC looks great
What the material to used as coring tool,diamond or tungsten carbide?.
chitharanjen kg tungsten carbide usually
Seth Carron ,Thank you.
Carbine forsure
how much, i need to make a hole on Sheetrock to install a light fixture
Feel free to give us a call 866-987-7297 and we can walk you through.
This is very smart way to drill concrete,Can you send me tools list please? I just subscribe your channel , all the time I have to use heavy rotary hammer .
E-mail us at marketing@ussaws.com or give us a call at 866-987-7297 and we can get you a list.
@@USSAWS sir pleas solve my problem. I need core ez system. How to i buy? I am from india.
Одно отверстие один анкер. А если выбуривать дверной проем?
Sir how much price in indian Rupees
وين تباع هذي القطعه في السعوديه
عساك حصلته بس
سلام عليكم حصلت في لسعوديه أخوك من العراق رايد منه
As a plumber , I want one...
Feel free to reach out to us at 866-987-7297 or sales@ussaws.com
looks good
I want to buy core drill in India can you help me in buying the product
I am sorry we only sell in the U.S.
This better than hilti
I want tis product..
I am also need this
take my money !!!
It's just to make hole isn't good for testing core samples.
Woaw welcome 🌹 Tahank you 🌹
I need this one
You can buy online at www.ussaws.com or give us a call 866-987-7297.
How much does it go for
Hi Jose! Visit us at www.ussaws.com/water-sewer/concrete-drilling/core-ez for pricing.
lol half of these people are asking for this channel to contact them when they can easily look up the company online. and buy it there for ~$3,000
indians dont really understand how the internet works
You dont pay any atention to those. Not real clients...
Hi
How to get this in india
how expensive the drill bits and Drilling System
visit our website: www.ussaws.com
Quiero ésa máquina cuánto cuesta$ soy de Argentina
it is looks as grinder tool> there is a gear add to it chang it to core drill
pls where i find the gear
It is a core drill.
Ha! "US Saw" with a GERMAN Metabo angle grinder ;-)
accessory
jojohome shit everyone better know metabo is the best.
jojohome
All made in China........
Metabo proudly produces all high end products here in Germany. They do
their own development, casting, injection molding, and motor winding. They also assemble their products here. Please inform yourself before posting.
Greets from Germany ;)
HVBasti
Metabo makes "high end" stuff?
price?
Here is a link to the Core EZ: ussaws.com/product/core-ez-core-drilling-machine/
How much this attachment....?
Naic bro
Wood carpantar shahzaib
Here is the real question can it cut though a reinforced safe
Wher i can buy this machine and how cost
Visit our website: www.ussaws.com
Hii sir how to purchase this product
Hi, you can purchase at www.ussaws.com/water-sewer/concrete-drilling
Open a bank vault with this things
Xavier Ancarno bout to say that, happened as well in some bank stealing over 1 mill in pounds
Just what I was thinking ;)
Hatton garden heist
My first thought!
Xavier Ancarno not really after pumping concrete for many years they add stuff into the concrete that will slow the bit cover the diamonds and eventually lock up the bit it's in the concrete mix most modern banks have shredded Steel along with ball bearings and rebar all around