Thanks for the video. At what interval should we replace rear brake shoe in ford figo diesel 2012 ABS model ?. When I apply hand brake in uphill, the car still moves back bit ,then I have to move the hand brake lever further up to make the car stop and stand . Mine has run 54000 kms .
Thats normal. ford older model has tough brake shoes and need extra strength to lock in place. Rear brakes on most car goes beyond 1.5 lk kms. Even mine crossed 2.4 lk kms with stock brake shoes. Front pads needs frequent changing and care.
Hi brother i follow almost all your videos to service my Figo. But in this case the rear left wheel play is still there after replacing the bearings also. Could you please suggest.
Do check the spindle if its tightly bolted to the cross bar. There's nly two things to make the rear wheel loose. Non proper fitment of bearing or spindle nut not torqued properly. Or the bearing is not the correct spec.
I have a Indian Ford fiesta classic 1.4 TDCi 2006 model. Need to replace rear brake shoe. Parts dealer says there are 2 types of brake shoe but he does not know which type for 2006 model. Is it the same type as in the video(6 holes) for 2006 model or there is another one that has only 2 holes in the shoe?
Hi bro nice video and info. Can u tell me the location of wiper relay. Becoz wen ever i on my wiper its goes up but doesn't go to home position. In fast operation it will work but in slow. It goes up and it will not reurn in home position
Bro its on the extreme right side below the steering wheel. There's a box where harness goes in. Wiper controls sits inside it. Its a bit hard to reach.
To adjust, have to remove the central panel inside. There will be two torx screw on both sides of central panel on back side. Move the front seat forward and will see them. Take them off and reomve the panel. You will find a 10mm adjsting nut on the cable. Just adjst it.
Bearing can be re greased but if its found dry enough or crossed over 40k or 50k kms.Jst put your finger in the middle part ie that lil seperation and see if there's grease in it. And the spindle, its jst need to be wet thats all for easy pulling out and pushing in ie drum. And the abs ring, No it should be clean as new or the brake dust and metal spreads will be collected fast on the ring and it will affect the abs sensor to read wrong.
Mate, on the Figo 2nd gen on the rear wheel there is a small cap covering the center lug nut, can we remove that or we have to remove the wheel separately and then the drum separately using bolts?
The small cover u reffer should be the hub spindle nut,the big one. You can pry the cover out without removing the wheel, but why would you remove the dust cover simply?
@@dailyhandsdiy The Figo 2nd gen has a different spindle. One has to remove the wheels to access the drum, I think. Not as easy as the first gen where the spindle nut is in center.
Oh yes yes sry, my mistake, new figo has a floating drum setup, have to remove the wheel, with a hammer hit on drum edges. it should come right off. Or There's a hole where a bolt goes in. torque it nd the drum comes off right away
Ford fluids have greate drain interval so at 1 lk kms you may check the fluid discoloration and change if wanted. If you are talking about any other brand 40k to 50k should be considered.
No need to wry, one, could be improper tyre air pressure, second improper steering camber, third if one tyre is smaller than other or one wearing fast. Fourth brake grabing. A bad alignment could also cause this problem. These are the possible options or chances.
My brakes seem like it sinks farther than it should altho my fronts do need replacing soon I should adjust the backs by backing up if I'm not mistaken and hit them hard because I drive and slow down with lightly hitting the brakes IDK Dogg I'm tired 2200 I'm goin sleep
@@dailyhandsdiy no when i turn my car on right side even when tyre has correct air in it it feels jerky and like if you are turning a punctured vehicle
oh feels like suspension bushing is going bad. Or May be ball joint of lower control arm, or tie rod end. For bushing, have to go under the car and check for cracked lower arm rubber bushing. and for worn ball joints, jack the car up and check wheather the wheel has horizondal or vertical plays or shakes. for both wheels.
Perfection has no alternative and its never demonstrated.....its automatically seen. Dts why....use no short cuts....do it as it needs to be done..... without using ur own ideas or brains, A multi-million company which makes n lays the method aren't mad to accept your ideas js becoz you are some aira gaira uneducated mechanic. Never ever tolerate this kind if work. Just see the difference. This video will show the perfect way that needs to be done. 💯
Wow I never thought to keep the wheel on the drum. What an easy solution.
Thank you for such a good video.
Any time mate... :)
Hehe, you've done this before! Last time I did my Transit it bent my mind. This is going to help me hugely with my fiesta.
Yup, these drum brakes are pretty much same for most of the cars. :D
Thanks for the video. At what interval should we replace rear brake shoe in ford figo diesel 2012 ABS model ?. When I apply hand brake in uphill, the car still moves back bit ,then I have to move the hand brake lever further up to make the car stop and stand . Mine has run 54000 kms .
Thats normal. ford older model has tough brake shoes and need extra strength to lock in place. Rear brakes on most car goes beyond 1.5 lk kms. Even mine crossed 2.4 lk kms with stock brake shoes. Front pads needs frequent changing and care.
Thanku sir bahut bahut thanks plzz aap ecosports ki rear leather change karna dekha do plzz sir
Sure brother
Adjuster ko kese set kare ki brake tiet lage nut ko niche gumaye ya uper
vo dekna hoga brother. anticlockwise gunma padega tight hone keliye
@@dailyhandsdiy anticlockwise ke uper ek video bano. Please sir
Is video me vo neeche k tara adjuster gunma chye tight hone klye.
@@dailyhandsdiy To sir dono drum me niche hi karna padta hai. Or Sabi car me niche hi karna hai kya
nei nei left side ( passenger side) neeche, right (Driver side) uppar...ye karke drum vapas rekke deklo tight hora ya nei..
Hi brother i follow almost all your videos to service my Figo. But in this case the rear left wheel play is still there after replacing the bearings also. Could you please suggest.
Do check the spindle if its tightly bolted to the cross bar. There's nly two things to make the rear wheel loose. Non proper fitment of bearing or spindle nut not torqued properly. Or the bearing is not the correct spec.
Sir please ford eco sports ki rear lether bta do change karke plzzz
Gaadi nei ayi bro...ek bar ane do... 😌
Ley lo bhai udhar kisi ki sarive karne ko bahut important ha plzz
I have a Indian Ford fiesta classic 1.4 TDCi 2006 model. Need to replace rear brake shoe. Parts dealer says there are 2 types of brake shoe but he does not know which type for 2006 model. Is it the same type as in the video(6 holes) for 2006 model or there is another one that has only 2 holes in the shoe?
Im not quite sure abt this as the drum should be removed to check which type is equiped. If its abs then the same from the video is used.
Thank you.. It has ABS.. It must be the same as in the video
Yup abs models have the same design.
Hi bro nice video and info. Can u tell me the location of wiper relay. Becoz wen ever i on my wiper its goes up but doesn't go to home position. In fast operation it will work but in slow. It goes up and it will not reurn in home position
Bro its on the extreme right side below the steering wheel. There's a box where harness goes in. Wiper controls sits inside it. Its a bit hard to reach.
@@dailyhandsdiy thank u
welcome bro
Plzzz sir ecosports ki rear lether change karna dekha do plzz sir
Will do that brother. for sure.
Thanku sir plzz deply btana sir ak ak chiz plzzz
Nice video.
Please make video on figo engine maintenance
Sure brother. :D
How to adjust the brakes setting ?
There's an adjuster to set the brake shoe gap...need minus to gently rotate the ratchet mechanism till the drum seats in firmly
@@dailyhandsdiy ok brother
Pls also tell how to tighten the hand brake in Figo.. thankyou
To adjust, have to remove the central panel inside. There will be two torx screw on both sides of central panel on back side. Move the front seat forward and will see them. Take them off and reomve the panel. You will find a 10mm adjsting nut on the cable. Just adjst it.
@@dailyhandsdiy thank you for quick reply
No problem bro..
when you wiped lube off the hub don't you have to re grease it? I just don't want to mess up if your supposed to
Did you mean the spindle or the magnetic ring or the bearing?
@@dailyhandsdiy yes that's what I meant, sorry lol, dont know the terms well
Bearing can be re greased but if its found dry enough or crossed over 40k or 50k kms.Jst put your finger in the middle part ie that lil seperation and see if there's grease in it.
And the spindle, its jst need to be wet thats all for easy pulling out and pushing in ie drum.
And the abs ring, No it should be clean as new or the brake dust and metal spreads will be collected fast on the ring and it will affect the abs sensor to read wrong.
Ford fogo work good work bro keep it up
Thank you bro will update with more ✌️
Bhai one video on steering and ball joints explanation please
Bro did you mean tie rod ends, control arms an ol.. i have video replacing all those. Pls refer my channel listings on ford figo.
Is the left side drum locking nut a reverse thread ? Or normal thread same as right hand side? In the video it looks like same?
Thanks
its the same bro, turn clockwise tight it gets and counter, lose it goes.. like normal nuts.
tks needed to see the autoadjuster
😁✌️
Bro in description can you add part name and its series
Do you mean the brake pad?
Very informative and good video. Thank you very much.
Alwys welcome.
Mate, on the Figo 2nd gen on the rear wheel there is a small cap covering the center lug nut, can we remove that or we have to remove the wheel separately and then the drum separately using bolts?
The small cover u reffer should be the hub spindle nut,the big one. You can pry the cover out without removing the wheel, but why would you remove the dust cover simply?
@@dailyhandsdiy The Figo 2nd gen has a different spindle. One has to remove the wheels to access the drum, I think. Not as easy as the first gen where the spindle nut is in center.
Oh yes yes sry, my mistake, new figo has a floating drum setup, have to remove the wheel, with a hammer hit on drum edges. it should come right off. Or There's a hole where a bolt goes in. torque it nd the drum comes off right away
@@dailyhandsdiy Absolutely right :)
😁😁
Please tell cleaning period km ? Or year?
Its actualy done at every 50k kms. Its not the cleaning more imp but more likely to check the shoe condition.
@@dailyhandsdiyThanks for reply
what about break fluid change
Km?
Ford fluids have greate drain interval so at 1 lk kms you may check the fluid discoloration and change if wanted. If you are talking about any other brand 40k to 50k should be considered.
My vehicle is turning slightly towards left, very slightly what will be the problem
No need to wry, one, could be improper tyre air pressure, second improper steering camber, third if one tyre is smaller than other or one wearing fast. Fourth brake grabing. A bad alignment could also cause this problem. These are the possible options or chances.
One more question bro oil is leaking badly from various parts of engine what will be problems
Bro please specify the parts if possibe. There are many oil seals in various parts of engine, they can wear out and cause oil leaks.
from front of engine beside fan
Please specify in detail I feel very bad for that leakage
Nice job Dude
Thnks mate...
Fan belt laganeka tarika bataye
Bro apka gadi konsi he?
Thank you bro
Always welcome bro
What year is that?
its 2010 model, but its same for all ford cars and most other cars
My brakes seem like it sinks farther than it should altho my fronts do need replacing soon I should adjust the backs by backing up if I'm not mistaken and hit them hard because I drive and slow down with lightly hitting the brakes IDK Dogg I'm tired 2200 I'm goin sleep
Adjusting the rear brakes will resolve the sinking issue.
Sir r u from chennai
.?
I need to contact you for imp advice...can u help us provindin any contact info
MY CAR WHEN TURN ON RIGHT IT FEELS LIKE IM TURNING A CAR WITH FLAT CAR
I dint get that bro. feel flat means?
@@dailyhandsdiy flat means punctured tyre it feels when cornering on right side
i gues if you go straight steering goes right. a small pull towards right. ryt?
@@dailyhandsdiy no when i turn my car on right side even when tyre has correct air in it it feels jerky and like if you are turning a punctured vehicle
oh feels like suspension bushing is going bad. Or May be ball joint of lower control arm, or tie rod end. For bushing, have to go under the car and check for cracked lower arm rubber bushing. and for worn ball joints, jack the car up and check wheather the wheel has horizondal or vertical plays or shakes. for both wheels.
Nice
😁👍
Perfection has no alternative and its never demonstrated.....its automatically seen.
Dts why....use no short cuts....do it as it needs to be done..... without using ur own ideas or brains,
A multi-million company which makes n lays the method aren't mad to accept your ideas js becoz you are some aira gaira uneducated mechanic.
Never ever tolerate this kind if work.
Just see the difference.
This video will show the perfect way that needs to be done.
💯
Made my day thankyou