Backup saving parameters on a Fanuc 0-TC control, Miyano CNC Lathe, CNC Digital, Inc.

Поділитися
Вставка
  • Опубліковано 29 жов 2024
  • Backup or saving parameters on a Fanuc 0-TC control.
    Download to your PC.
    Fanuc Parameters 2.0=1 which equals two stop bits.
    and Parameter 552 = 10 = 4800 baud rate
    These two parameters must match what is in your PC software for file transfer.
    Miyano CNC Lathe,
    CNC Digital, Inc. 440-721-7100
    www.cncdigital.com

КОМЕНТАРІ • 29

  • @ayyazonline
    @ayyazonline 3 роки тому +1

    Hey! Why didn't you press EOB when downloading the diagnostics?
    And what was that you explained at the end about parameter no.1 and 502 and 503. Can you please explain it into simple words. I will be very grateful.

    • @jonnydeen6952
      @jonnydeen6952 2 роки тому

      The bit at the end was regarding the serial communication settings. This should be established before transferring files as you need both the control and pc to have matching settings. These include the baud rate, data bit length, stop bit length. Hardware handshake etc. If your coms settings work and you can transfer files via rs232 then you can ignore those settings as they are fine.

  • @KaraokeNha-l2p
    @KaraokeNha-l2p Місяць тому

    Thank you for your share the video.
    Can you share with me the parameters? Because I accidentally deleted the parameter of the machine.
    I appreciate your help.

  • @MrSerkamil
    @MrSerkamil Рік тому

    Thank you very much!

  • @sergrura5301
    @sergrura5301 2 роки тому

    Thanks all work great!!

  • @romanadeleon7938
    @romanadeleon7938 2 роки тому +2

    What is the name of that software? Where can I get it from?

  • @chrishopkins7620
    @chrishopkins7620 3 роки тому +1

    Thank you for the very informational video! Do you have the procedure for loading the parameters back into the machine? One of our machines has had the Delete+Reset command done to it and im starting fresh. I was hoping I could copy the parameters from my identical machine and load them into my wiped one.

    • @cncdigitalCNCMachines
      @cncdigitalCNCMachines  3 роки тому +2

      I do not have a video.
      However.
      INPUT OF SETTING PARAMETERS PROCEDURE
      PRESS DGNOS/PARAM KEY
      (SETTING PARAMETERS INPUT)
      (MAKE SURE SETTING PAGE 1 ARE CORRECT)
      ISO=1
      I/O=0
      E-STOP PRESSED IN
      PWE=1
      MEMORY PROTECT KEY OFF (TO THE RIGHT / )
      MODE SWITCH = EDIT
      ENTER 900 OPTION PARAMETERS BY HAND
      CYCLE POWER TO ACCEPT OPTION PARAMETERS
      E-STOP OUT
      PRESS INPUT LSK SIGNAL FLASHES (LOWER RIGHT SCREEN)
      SEND DATA FROM PC. INPUT SIGNAL FLASHES (DATA BEING ACCEPTED)
      INPUT PC DIAGNOSTIC PARAMETERS, TIMERS, COUNTERS.
      PRESS DGNOS / PARAM KEY TWICE.
      (MAKE SURE YOU ARE IN DIAGOSTIC SCREEN)
      (MAKE SURE SETTING PARAMETER PAGE 1)
      ISO=1
      I/O=0
      MEMORY PROTECT KEY OFF (TO THE RIGHT / )
      MODE SWITCH = EDIT
      PREPARE CONTROL TO RECEIVE DATA (WAITING)
      PRESS INPUT LSK SIGNAL FLASHES (LOWER RIGHT SCREEN)
      SEND DATA FROM PC. INPUT SIGNAL FLASHES (DATA BEING ACCEPTED)

    • @chrishopkins7620
      @chrishopkins7620 3 роки тому

      @@cncdigitalCNCMachines Thank you for your reply! I had actually figured it out on my own but I know that this will be helpful for many others.

    • @schrottmail6381
      @schrottmail6381 Рік тому

      ​@@chrishopkins7620 Do you have a backup? We had the same problem with the reset but no backup

  • @fabuloustshirtsonline
    @fabuloustshirtsonline Рік тому

    Dou you know how to change the direction of clamping of that machine in the parameters screen?

  • @thuongvuvan9223
    @thuongvuvan9223 2 роки тому +1

    Please help me how to backup ladder program of fanuc 0 series

  • @GerardoRodriguez-vg6fi
    @GerardoRodriguez-vg6fi 4 місяці тому +1

    Thank you so much for you video. Can you share the parámeter with me.? Please?

  • @waynedejong6228
    @waynedejong6228 3 роки тому

    This is a great video! I am having problems that the code is coming out in machine language instead of values that I can read any ideas?

  • @mousongie
    @mousongie 3 роки тому

    Hi! May i have the configuration for the Rs 232 25pin -Usb ? Does it need a special hardware to connect the pc to the machine as shown in this video.

    • @cncdigitalCNCMachines
      @cncdigitalCNCMachines  3 роки тому

      No. I purchased the cable on ebay. Just searched for RS-232 to usb CNC cable.

  • @VijayKumar-wt1td
    @VijayKumar-wt1td 3 роки тому +1

    Hai sir , let me know how to backup plc also

  • @minhtuyetnguyen8024
    @minhtuyetnguyen8024 3 роки тому

    Hi Sir! Can you send to me this Software.Thanks

    • @cncdigitalCNCMachines
      @cncdigitalCNCMachines  3 роки тому

      This is paid for software. We do sell it or have the ability to give it to you. Sorry.

    • @davidfliger7406
      @davidfliger7406 Рік тому

      What is the name of the software used here

    • @schrottmail6381
      @schrottmail6381 Рік тому

      ​@@cncdigitalCNCMachines i would like to buy one too, but how?

  • @MukeshPatel-f1j
    @MukeshPatel-f1j 5 місяців тому

    Ot backup

  • @MukeshPatel-f1j
    @MukeshPatel-f1j 5 місяців тому

    Hi