It's a Series 1 car, but its been swapped with Series 2 parts. The lights, hood and the interior (seats, door cards, etc) is all Series 1. The front bar, rear bar, skirts and rear boot lid (spoiler and the lock mechanism) are Series 2. Looks like a Series 2 engine as well. The Series "1.5" with the series 2 body came out in mid 1996, and full series 2 late 1996. I've had a few R33's and whining gearbox is **not** normal. The advice sounds spot on from listening to it, sounds like its low on fluid. I'd really drain it and replace the fluid asap to reduce the wear on it. From the sound of your idle, you might need to also check the IAC valve and make sure its clean, and check the BOV gasket/spring.
Yo, a few things to help you out: - It's a series 2 engine. You can tell by the fact it has 2 connectors on the throttle body instead of 1 and there's no igniter for the coil packs. - You're missing a bolt off your J-pipe coming straight off the turbo. You no doubt have a boost leak there, which may be causing you to run rich, which could explain the flame/s and rough sound. - A common leak, near where you pointed at the rear of the engine, is the crossover hard-line that feeds coolant to the turbo. Check that, it's a common area for a leak. - The hoses you pointed to that you thought were for your A/C are actually for your carbon canister (that is missing), you'll need to replace that. - It looks like you have something connected in line with the hose vacuum line that goes to the fuel pressure regulator (towards the front of the engine, drivers side, end of the fuel rail). I'm not sure what that is but having anything connected to the FPR line is a bad idea, you should likely remove it. - You mentioned connecting the hoses off your two rocker covers. Do make sure you add a catch can at least so they can vent, or, even better, connect them back to the pipe that feeds air to the turbo, as that's where they should run (they're supposed to have vacuum) - The cable/plug that's just chillin near your air filter is for the stock boost solenoid (that looks like its missing). I don''t believe there's any harm with that given you run aftermarket boost control. - Your turbo is a standard 21U that comes with that engine. Hope this helps.
the water leak could be the heater valve bit on the fire wall, ive had a few crack the brittle plastic. replace with new or just put a brass barbed fitting to delete. But also had the turbo feed (which is what your talking about) leak on a RB20 also, again a barbed T piece worked here. if your doing all of this might be worth while replacing all the coolant hoses and oil filter heat exchange Oil seal. its anoying to do so enjoy. Apart from these thoughts this guy is on the money.
@@inmaniac Yes most likely a series 1 with s2 engine swap and front bumper, interior is series 1, headlights look series 1 as well and the clear skyline garnish is all series 1
easiest way to tell if its a series 2 or not is the series 2 has a passenger airbag and the series 1 does not. the 95 model is a funny year as some series 1s came with series 2 parts. i own a series 1 skyline that came factory with a series 2 engine which is considered the series 1.5
$3000 Wow.. And now for this condition and a manual they usually go for $18,000+ even if it has a few problems 💀 One of the best skyline finds I have seen for its price!!
If the car doesn't exhibit any other signs of headgasket failure (water/oil mixing, running hot etc) than it more likely issues with valves sealing. Dont listen to people who tell you the pistons are trash, generally its people winding boost in on stock ECU and stock turbo. Japan had far better quality fuel in general in the 90's. The stock tunes on these ECU's generally are for better fuel to start with, then when people start pumping boost in from the stock t28 cause big IAT's they detonate like crap and crack ringlands. If the tune is good the pistons will be fine. My opinion from what you have said in this vid is valves. Do a leakdown test and you will know for sure. Good price though! very jealous!
Congratulations Zacster enjoy it . Can’t wait until you get it set up for the track . We’ll all come along for the ride and learn about the car with ya 😀.
Hey Zac check out Aussie bloke Tangles 01 videos , He knows his way around these cars . He might have some suggestions and tips for you about your engine. R32 GTST Skyline Time Attack Build - RB25 Knock Investigation - Inspect ... ua-cam.com/video/PZ83BEzavYw/v-deo.html
Pull the head off. Have it machined flat, valves seats redone and fit a tripple layer metal headgasket and arp head studs. Then do the gates timing belt and a water pump and new thermostat. Front facing plenumn and spit fire coils. Then a 3 inch dump pipe, 100 cell cat, resonator and straight through muffler. Will sound good and be reliable.
used to have an r33 gtst 96 model. Damn I love those cars! wish I have have kept it lol, who'd have known the value would sky rocket. Have to admit, they're bloody slow stock standard.
s2 converted for sure s2 started in 96 as well as the s1 seats and s1 rear garnish also S1 RB25DET use an external ignitor rather connectors on the left hand side will be from the factory boost solenoid which has been deleted for the boost t
doing regular oil changes and actually looking after your car is what help the longevity, Also RB engines need to breath so 100% on a proper catch can setup.
im really keen to see your progress with the car and where u can take it in the future please keep us updated and upload vids of you doing things with the car ❤️
i remember being that young and having the excitment of having a project car & i also remember saying the words "i'll get it fixed" which were famous last words hahaha
Tristan this is Queensland. He went from Childers all the way to Brisbane. He went through Tiro and Gympie and on the Bruce Highway 🛣 and he drove 310KM without stopping once.
Always had a soft spot for the r33 i think the front end has a good aggressive look to it and theres heaps you can do to make it have a great stance to em, coil overs etc.. good vid mate! 👍😎
Be sure to remember it's a drift car! They're bound to eventually getting damaged when pulling skids or tandem among narrow courses. I recommend not throwing a heap of cash, as bumpers and parts do come and go by the bucket load. **only writing this comment because I made the mistake of kitting out my 240sx that got totalled in a tandem :/
@@ZacBaldy just so you know I personally think your r33 is a series 1.5 because i didn't see an igniter when you opened the engine bay because series 2 started in 1996 but if it has a igniter its a series one.
Full detail? I look forward to seeing what you get out of it after you start by removing all the seats and floor carpet. Hell, I found a bit of factory foam still stuck in one of the under passenger seat vents in my car that pre-delivery missed back in 2003. lol. After that a good start is to change every single fluid.
Skylines are what made me fall in love with cars.. I just hope you’re not in over your head. On a side note: Turbo Barra swapping an R33 would possibly be the coolest thing anyone could build on UA-cam. Plus keeping it relevant to most of your core subscribers. Just a thought.
Good score, But in all honesty your point of difference is your channel is based around the falcon there are 48994894 other youtubers making videos about skylines and the RB engine and drifting in general. So dont loose touch with your roots.
seen an na auto r34 that didn't start for $2.5k complete. cheapest of the year for online gold coast/qld prices. not the car for me, but someone who could get it started plus cleaned up would have got a deal.
If you need any help just message me Fyi: that pipe at the front is the fuel tank breather that is meant to go to your carbon canister which is missing
Yeah it's a standard turbo mate, it's a run of the mill piece of shit r33 that has had a boost tee put on by dumb kids who don't know what they're doing just to wreck the motor even faster. You literally see one every time you leave the house down here on the central coast. I'm happy for you since it didn't break the bank. But be aware that this thing is gonna cost you big money to get it back up to scratch. Its unroadworthy as fuck. That high mount manifold is screamer pipe ready, has a bent base plate and looks to have jokes for welds. What a dud.
The drift scene is brissy is sick as fuck
It’s so weird seeing drive on the same roads I go on lol
If/when you go through Tiaro next, stop at the butcher and grab some bacon. Best you will have!
It's a Series 1 car, but its been swapped with Series 2 parts.
The lights, hood and the interior (seats, door cards, etc) is all Series 1.
The front bar, rear bar, skirts and rear boot lid (spoiler and the lock mechanism) are Series 2. Looks like a Series 2 engine as well.
The Series "1.5" with the series 2 body came out in mid 1996, and full series 2 late 1996.
I've had a few R33's and whining gearbox is **not** normal. The advice sounds spot on from listening to it, sounds like its low on fluid.
I'd really drain it and replace the fluid asap to reduce the wear on it.
From the sound of your idle, you might need to also check the IAC valve and make sure its clean, and check the BOV gasket/spring.
Jarsky agreed
Soon as i saw that power/snow button 🤣🤣 gald you know its been swapped tho
Feral sound 5:49
Fuck yeah looks mint man
Yo, a few things to help you out:
- It's a series 2 engine. You can tell by the fact it has 2 connectors on the throttle body instead of 1 and there's no igniter for the coil packs.
- You're missing a bolt off your J-pipe coming straight off the turbo. You no doubt have a boost leak there, which may be causing you to run rich, which could explain the flame/s and rough sound.
- A common leak, near where you pointed at the rear of the engine, is the crossover hard-line that feeds coolant to the turbo. Check that, it's a common area for a leak.
- The hoses you pointed to that you thought were for your A/C are actually for your carbon canister (that is missing), you'll need to replace that.
- It looks like you have something connected in line with the hose vacuum line that goes to the fuel pressure regulator (towards the front of the engine, drivers side, end of the fuel rail). I'm not sure what that is but having anything connected to the FPR line is a bad idea, you should likely remove it.
- You mentioned connecting the hoses off your two rocker covers. Do make sure you add a catch can at least so they can vent, or, even better, connect them back to the pipe that feeds air to the turbo, as that's where they should run (they're supposed to have vacuum)
- The cable/plug that's just chillin near your air filter is for the stock boost solenoid (that looks like its missing). I don''t believe there's any harm with that given you run aftermarket boost control.
- Your turbo is a standard 21U that comes with that engine.
Hope this helps.
Didn't series 2 start in 1996? This one is a 1995
TaffPlays I said the engine is Series 2 and it definitely is. If the car is indeed a series 1 which might be the case it’s had an engine swap.
the water leak could be the heater valve bit on the fire wall, ive had a few crack the brittle plastic. replace with new or just put a brass barbed fitting to delete. But also had the turbo feed (which is what your talking about) leak on a RB20 also, again a barbed T piece worked here.
if your doing all of this might be worth while replacing all the coolant hoses and oil filter heat exchange Oil seal. its anoying to do so enjoy.
Apart from these thoughts this guy is on the money.
@@inmaniac Yes most likely a series 1 with s2 engine swap and front bumper, interior is series 1, headlights look series 1 as well and the clear skyline garnish is all series 1
Definitely know your skyline's 👍
ONLY 3 GRAND !!!! thats steal no matter the issues
1 year today since this video was uploaded wow.
easiest way to tell if its a series 2 or not is the series 2 has a passenger airbag and the series 1 does not. the 95 model is a funny year as some series 1s came with series 2 parts. i own a series 1 skyline that came factory with a series 2 engine which is considered the series 1.5
$3000 Wow.. And now for this condition and a manual they usually go for $18,000+ even if it has a few problems 💀 One of the best skyline finds I have seen for its price!!
Hey mate, i was the bloke at Maccas that told you to do a skid from the Drive Thru window 🤠
Haha your a legend 😂😂
*You’re
The least you can expect from an adult is basic grammar.
Ruedi from obtk?
@@enjoyurmachine yes
Zac Fuck the haters just send it and learn at your own speed
unleaded 91 cheeeap
Do realise he bought a car, so he had to cut costs somewhere
13x,xxx kms plus the other 180,xxx kms on the other cluster before it was swapped hahaha.
If the car doesn't exhibit any other signs of headgasket failure (water/oil mixing, running hot etc) than it more likely issues with valves sealing. Dont listen to people who tell you the pistons are trash, generally its people winding boost in on stock ECU and stock turbo. Japan had far better quality fuel in general in the 90's. The stock tunes on these ECU's generally are for better fuel to start with, then when people start pumping boost in from the stock t28 cause big IAT's they detonate like crap and crack ringlands. If the tune is good the pistons will be fine.
My opinion from what you have said in this vid is valves. Do a leakdown test and you will know for sure. Good price though! very jealous!
That's fucked up needing a manual licence
It's sounding, running and drive much nicer now. Can't believe how quick it all took!
That gearbox sounds fucked 😂
Does anyone know where to buy a cheap Skyline in Melb??
I'm 13 and this is my dream car 😊
Gympie 5:18
wait how much did oldmate pay for it
What's your job like how did you afford your car?
Tiro 5:06
Left rear shock is fucked b the way.
Do u even have ur manual licence
How much?
Just remember how much cops pick on skylines in Australia, so you're fucked 😂
Hey can someone let me know where to buy some of these cars at a decent price in australia
Congratulations Zacster enjoy it . Can’t wait until you get it set up for the track . We’ll all come along for the ride and learn about the car with ya 😀.
Hey Zac check out Aussie bloke Tangles 01 videos , He knows his way around these cars . He might have some suggestions and tips for you about your engine.
R32 GTST Skyline Time Attack Build - RB25 Knock Investigation - Inspect ...
ua-cam.com/video/PZ83BEzavYw/v-deo.html
Jim Gourlas thanks very much for your nice comment man ❤️ really appreciate.
Pull the head off. Have it machined flat, valves seats redone and fit a tripple layer metal headgasket and arp head studs. Then do the gates timing belt and a water pump and new thermostat. Front facing plenumn and spit fire coils. Then a 3 inch dump pipe, 100 cell cat, resonator and straight through muffler. Will sound good and be reliable.
I'm most excited to teach you how to drive a manual car 😂
Sarah Best I hate you right now 😂😂
Sarah Best you just made my day with that comment. You should totally take the skyline to the shops and on road trips
I am the superior driver
Sarah Best you wish 😂
Wait he cant drive manual
I'm telling ya it's not the cheapest if it has 4 wheels and starts.
I sold a done up series 2 for legit 5 grand bro ahahah
@@bolevy9660 when did you sell it
Nothing better then a super cheap auto and auto barn build
Bro u could take the r33 headlights and put em on the Silvia s14 zenki and it wouldn’t look diffirent
'' car guy '' i dont have a manual licence
I did not even know there is such a thing as a manual license 😂🤦🏼♂️
BriaForPres do you live in australia
ツرقيم yes he does mate don’t assume his penis is a egg
not everyone has the same opportunities, don’t be a dick
Awesome work man!!
used to have an r33 gtst 96 model. Damn I love those cars! wish I have have kept it lol, who'd have known the value would sky rocket. Have to admit, they're bloody slow stock standard.
Good on ya Zac!
You need to get your block resleeved which means the engine is blown so it will need to go through a machine or a replacement
s2 converted for sure s2 started in 96 as well as the s1 seats and s1 rear garnish also S1 RB25DET use an external ignitor rather connectors on the left hand side will be from the factory boost solenoid which has been deleted for the boost t
doing regular oil changes and actually looking after your car is what help the longevity, Also RB engines need to breath so 100% on a proper catch can setup.
Tetra that’s all on the cards my dude 😁😁
im really keen to see your progress with the car and where u can take it in the future please keep us updated and upload vids of you doing things with the car ❤️
didn't think zac could drive manual
Lachlan Tresham I certainly can 😉
Sick car Zac can’t wait to see vid of you fixing it up
Is it tuned for 2step
Gear box whine ain’t to bad just sounds like a dog box or straight cut gears hahaha
Love that feral sounding skyline and maxi wrecked his brand new shoes how funny to me.
i remember being that young and having the excitment of having a project car & i also remember saying the words "i'll get it fixed" which were famous last words hahaha
I'm scared of this... but hey we will see :P
@@ZacBaldy haha good luck mate, i subbed just to see how far you'll get ;-)
I live in maryborough and I'm gonna miss seeing this thing cruise through town, good buy though!
Series 1
Pretty clean cheap r33 zak, big 👍👍
What state is this it’s so nice
Tristan this is Queensland. He went from Childers all the way to Brisbane. He went through Tiro and Gympie and on the Bruce Highway 🛣 and he drove 310KM without stopping once.
That's not cheap my mate got his for 1000 bucks cash now that's cheap
Next weeks video... My cheap skyline is thrashed needs 15k in repairs
Always had a soft spot for the r33 i think the front end has a good aggressive look to it and theres heaps you can do to make it have a great stance to em, coil overs etc.. good vid mate! 👍😎
might need a tune and a boost leak test
Motorized Bikes I’m thinking so too...
So glad I got to see it driving around at boundary road on the bruce highway. I hope Max like the turbo dose/bov next to him
Liam Poor hahaha was so cool! Can’t believe you thought it was Sammit 😉😂
@@ZacBaldy that's why I sent you a message. Didn't look like Max 😂😂
Be sure to remember it's a drift car! They're bound to eventually getting damaged when pulling skids or tandem among narrow courses. I recommend not throwing a heap of cash, as bumpers and parts do come and go by the bucket load. **only writing this comment because I made the mistake of kitting out my 240sx that got totalled in a tandem :/
Hey what up I don't live far from Gympie and would like to meet you
What suburb you from?
711 Cubing he’s from Brisbane. I live in Gympie to.
I live in Gympie.
is this bree r33
Man! Congratz on the car! I’m doing a rebuild serie on my R33 right now! It`s a massive project. But damn it`s fun!
Just put a barra in it 😂🤟
Ahhh na
3k Australian dollars is so good
Welcome to the skyline club :D
ItzFrenschy ayyy cheers bro! I need some help 😉😂
@@ZacBaldy just so you know I personally think your r33 is a series 1.5 because i didn't see an igniter when you opened the engine bay because series 2 started in 1996 but if it has a igniter its a series one.
lets go im so happy you got it cant wait for the vids on it
About to buy a 2005 BF XR6 Turbo. Whats the first thing I should do? Im thinking of getting the braided oil feed line for the turbo.
Just fyi bro full licence means full licence no need to get a manual licence
But if his licence says auto only he has too
I had that coolant leak in the same spot in my r33 it wasn’t too hard to change
Hey man, Glad to hear that! Do you know what part its called?
I found a couple diagrams with part numbers but I don’t really remember what it was called
I WANNA SEE A SATISFYING CLEANING VIDEO
Zac Miles next weekend 100%
i wasnt aware you needed to do another test to drive manual in nsw you dont... once you are on your green ps you can drive either manual or auto...
curtis green yeah... I was thinking of moving to NSW for a day...😂
Same here in SA, no manual or automatic licence can just drive either
@@ZacBaldy Come to South Australia where you can drive whatever transmission you want
Sammit 2.0....34 front?!?! Look forward to the journey #RBlife
ItsMe Deni hahaha cheers man ✌️ really appreciate it
Full detail? I look forward to seeing what you get out of it after you start by removing all the seats and floor carpet. Hell, I found a bit of factory foam still stuck in one of the under passenger seat vents in my car that pre-delivery missed back in 2003. lol. After that a good start is to change every single fluid.
Why wouldn’t you just get a manual licence in the first place?
Ping G always was sus about this guy biggest wannabe manual driver 😂😂
Him and his auto box triptonics 😂😂
Tristan Dent I literally drove Manila in the video...😂
Auto license gang
ZacBaldy oh hey Zac
You live like 500 meters away from me and I love the Chanel
And I use to work and build up engines so just dm me in instagrams _jake.thompson and I will come help you for free
Skylines are what made me fall in love with cars.. I just hope you’re not in over your head.
On a side note: Turbo Barra swapping an R33 would possibly be the coolest thing anyone could build on UA-cam. Plus keeping it relevant to most of your core subscribers. Just a thought.
Josh Lawrence hahaha cheers man! That’s never off the cards, but we will never know 😉
auto license xD
Rims, sound and good fitment will be mint
Good score, But in all honesty your point of difference is your channel is based around the falcon there are 48994894 other youtubers making videos about skylines and the RB engine and drifting in general. So dont loose touch with your roots.
PhantomXR 100% understand bro ✌️ the Falcon is never going
@@ZacBaldy Well this comment didn't age well....
Wtf, $3000
ik wth its rare to find a working skyline now for 3k and everyone is trying to get there hands on one atm 💀
Buy a rotary
Subbed for the sweet moustaches
seen an na auto r34 that didn't start for $2.5k complete. cheapest of the year for online gold coast/qld prices. not the car for me, but someone who could get it started plus cleaned up would have got a deal.
If you need any help just message me
Fyi: that pipe at the front is the fuel tank breather that is meant to go to your carbon canister which is missing
Nick Grech Thankyou so much man! I actually just jumped off the phone to Sammit also! Message me on Instagram 😁😁
ZacBaldy messaged mate
Nice civic first
Woohoo so happy to see the new project! So much content can be made with this car 😁😁
Hi, found one for 5.8k in bankstown nsw, was thinking boit getting it, thank god u made this vid 😂😂
What colour is it ? I think I've seen that!
@@nextgendrift3073 its black
Why would you not go for your licence in a manual
Sounds like my Ecotec with no exhaust
Yeah it's a standard turbo mate, it's a run of the mill piece of shit r33 that has had a boost tee put on by dumb kids who don't know what they're doing just to wreck the motor even faster. You literally see one every time you leave the house down here on the central coast. I'm happy for you since it didn't break the bank. But be aware that this thing is gonna cost you big money to get it back up to scratch. Its unroadworthy as fuck. That high mount manifold is screamer pipe ready, has a bent base plate and looks to have jokes for welds. What a dud.
Looks like it's done more than 136000ks, but still nice car👍 you going to need decent power and suspension to drift proper.
Pete Rose wait till she’s all clean and paint corrected 😉
It has the r33 s2 front and wing but the interior is all from a s1 I know there is a 1.5 but I’m not too sure what parts they use from what car
Brett Mason I don’t think that’s a series 1 wing as that’s the stock series 2 wing
The s1 wing was just like a little low style one the I’ve got that wing and it’s just the stock 2 but I changed to the Gtr from that
till the gerbox is fixed probably best that you granny shift (double clutch) it so you dont make the synchro's worse. Other than that, great video :)
You do realise that I was trying to sell
You mine for $600 😂😂
Where you located?
Jamie Richman Rockhampton
No worries looking for project but in W.A
33 skyline? for 600 bucks?
Luke Goldstone YeH
Could be head gasket mine needs replacing and all cylinders read around 120psi
Not bhed
Max Clarke good size
What is that on your upper lip
Fuggin mintttt