Parfait! Juste quelques précisions : - Attention en enlevant les aiguilles de bien les soulever par la partie centrale noire et pas par l'aiguille en elle même - Lorsque qu'on remet en place les aiguilles, ne pas les aligner avec le "zéro". Il faut les positionner entre 2 et 3 millimètres en dessous du zéro
@@solosolo1255 Yes, as I can see. I have my W169 with the 8V version, and need to reach 7V at the points. I am waiting 6 month for the reply. The colors are not good readable at the video. Is it so hard for all there to answer ???
Hola, si no tengo la fuente de energia para probar si la pantalla funciona una vez cambiada, puedo conectarla al auto y ponerla en contacto para verificar el funcionamiento? conectar solo la plaqueta con la nueva pantalla, puedo causar algún problema o daño? muchas gracias
Hi I followed your instructions and managed to change the screen. Everything works great but the rev indicator gets misaligned after a few days. I fix it and it happens again. The others work correctly. Any idea of how I can fix this? Do I have to set clockwise counterclockwise press it harder? Is it the same size with the speedometer indicator? I wonder wether I have misplaced it... Thank you in advance
It continues to work afterwards normally it just has a wrong starting point. Anyway I will switch them with the speedometer and see if it will work. Thank you for your help
My W169 LCD is dying and the only problem I see with replacing it myself is finding out if I need the 7V or 8V version....so....what will happen if I put a 7V LCD in a 8V instrument cluster without the resistor?? I don't have the connector you use to find out what version I have. There is no other way to find out?
Hi Ridder, no worries. You can just install the lcd and see if it works. When all is fine, ok. If you can´t see any signs, numbers then you have to solder the resistor. Normally nothing can happen if you try the lcd without resistor.
@@pixelfehlerhamburg9956 And the other way around? I've seen 8V versions (without resistor)...if you put that in a 7V cluster and you see nothing....than you need to buy the other version....you can't remove the resistor if it not there....
As resistors are reducing voltage, I guess the resistor is meant to be installed, if your voltage ist 8V, so it drops to 7V. But no guarantee though, someone else should confirm or correct me.
Very good. Now how about do same to A class W168 with flat cable using T bar and solder iron to fix it to the board. I've been looking for a demonstration of how to do this. It being a common problem for the A class model between 2002-04.
Hey! Can programming a new speedometer be done at home? My factory one wasn't working correctly, so I bought a new one, but it doesn't show the total kms (only 4 lines). I asked a mercedes dealer and I got an offer for 600 eus for repair cost. Thanks!
@@pixelfehlerhamburg9956 how do you get the needles to re-align once everything is reconnected? Mine are moving to the wrong position once the cluster turns on.
hi… ich hätte gerne 2 fragen: 1) funktioniert die 8 volt version auch ohne löten des widerstandes? 2) Nach dem Zusammenbau einfach den Stecker einstecken oder muss die Mercedes-Software installiert werden, damit das Display funktioniert? ... danke
@@pixelfehlerhamburg9956Ciao quindi se io prendo la versione 7 v e il display e 8 v se io provo non si brucia niente non si accende e bisogna saldare la resistenza da quanto deve essere la resistenza ?
Lieber Herr! Bitte hilf mir. Der Drehzahlmesser unserer B-Klasse W245, Baujahr 2005, lügt. Manchmal zeigt er mehr, manchmal weniger an, aber manchmal bleibt er auf Null und bewegt sich nicht. Wo soll ich nach dem Grund suchen, warum hpol so viel und so viel anzeigt? Was könnte der wahrscheinlichste Grund sein. Eventuell ein Lötfehler? Oder könnte ein Kontakt defekt sein? Vielen Dank im Voraus für Ihre freundliche Hilfe! Mit freundlichen Grüßen, János Bohus
THANK YOU!!! i must say it was hard to remove the pointers!
But you have done it! Great!
Parfait!
Juste quelques précisions :
- Attention en enlevant les aiguilles de bien les soulever par la partie centrale noire et pas par l'aiguille en elle même
- Lorsque qu'on remet en place les aiguilles, ne pas les aligner avec le "zéro". Il faut les positionner entre 2 et 3 millimètres en dessous du zéro
Il faut prendre le 7v ou le 8v avec résistance ?
Good morning. It is not well readable the resistor colors. What is the resistance, please?
Hi, can you please tell me, what exactly rezistor it is? 🙏
Whats the resistor value please?
What is the resistor value? Thanks
Top secret ///
@@solosolo1255 Yes, as I can see. I have my W169 with the 8V version, and need to reach 7V at the points. I am waiting 6 month for the reply. The colors are not good readable at the video. Is it so hard for all there to answer ???
Hi, did you get the resistance somewhere?
So basically if you get 8v then you add the resistor to drop it to 7v range in order the LCD to work ?
Hello! Why do you align all needles to the "2" pm before removing? Thank you!
Hi, just for better remove feeling for me
@@pixelfehlerhamburg9956 Thank you!
I would love to see how to Change Stepper Motors on a 2007 GL450 Speedo. Thank you.
Ok, i will keep it in mind
Hola, si no tengo la fuente de energia para probar si la pantalla funciona una vez cambiada, puedo conectarla al auto y ponerla en contacto para verificar el funcionamiento? conectar solo la plaqueta con la nueva pantalla, puedo causar algún problema o daño? muchas gracias
Hi I followed your instructions and managed to change the screen. Everything works great but the rev indicator gets misaligned after a few days. I fix it and it happens again. The others work correctly. Any idea of how I can fix this? Do I have to set clockwise counterclockwise press it harder? Is it the same size with the speedometer indicator? I wonder wether I have misplaced it... Thank you in advance
Hard to say what happened. Sometimes the stepper motors get damaged after removing. Maybe you need a new one?
It continues to work afterwards normally it just has a wrong starting point. Anyway I will switch them with the speedometer and see if it will work. Thank you for your help
I ended up changing the speedometer indicator with the rev indicator and it seems to be working fine. Maybe I had them misplaced
My W169 LCD is dying and the only problem I see with replacing it myself is finding out if I need the 7V or 8V version....so....what will happen if I put a 7V LCD in a 8V instrument cluster without the resistor?? I don't have the connector you use to find out what version I have. There is no other way to find out?
Hi Ridder, no worries. You can just install the lcd and see if it works. When all is fine, ok. If you can´t see any signs, numbers then you have to solder the resistor. Normally nothing can happen if you try the lcd without resistor.
@@pixelfehlerhamburg9956 And the other way around? I've seen 8V versions (without resistor)...if you put that in a 7V cluster and you see nothing....than you need to buy the other version....you can't remove the resistor if it not there....
@@maasland64 We have only 7V
@@pixelfehlerhamburg9956 OK, and what is the difference between V1 and V2? Almost ready to order.....
@@maasland64 we have only 1 version
7v or 8v with resistor?
As resistors are reducing voltage, I guess the resistor is meant to be installed, if your voltage ist 8V, so it drops to 7V. But no guarantee though, someone else should confirm or correct me.
Very good. Now how about do same to A class W168 with flat cable using T bar and solder iron to fix it to the board. I've been looking for a demonstration of how to do this. It being a common problem for the A class model between 2002-04.
Frank, we are working on it.
Hey! Can programming a new speedometer be done at home? My factory one wasn't working correctly, so I bought a new one, but it doesn't show the total kms (only 4 lines). I asked a mercedes dealer and I got an offer for 600 eus for repair cost. Thanks!
What if I just unplug the odometer order a new one and plug in will it work like that or it requires programming??
It requires programming
Hi I have a W169 8V and I buy a LCD V7 version. which is the ohms of the resistor?
Salve , e per reimpostare i km come si fa ? Grazie
Hello i don´t know what you mean. Sorry
Is this the same procedure for a 2007 C-230? The instrument cluster and screen look the same.
It´s a bit similar
@@pixelfehlerhamburg9956 how do you get the needles to re-align once everything is reconnected? Mine are moving to the wrong position once the cluster turns on.
can u teach how to replace air-conditioning panel on w245
No sorry
Di mana sy bisa beli
hi… ich hätte gerne 2 fragen:
1) funktioniert die 8 volt version auch ohne löten des widerstandes?
2) Nach dem Zusammenbau einfach den Stecker einstecken oder muss die Mercedes-Software installiert werden, damit das Display funktioniert? ... danke
Hallo, entweder das Display funktioniert sofort oder es muss der Widerstand eingelötet werden. Es muss keine Software installiert werden.
@@pixelfehlerhamburg9956Ciao quindi se io prendo la versione 7 v e il display e 8 v se io provo non si brucia niente non si accende e bisogna saldare la resistenza da quanto deve essere la resistenza ?
Voglio dire non c'è pericolo che si brucia qualcosa se il display e 8 volt e uno mette un 7 volt e così?
How much the LCD display cost for B class Merc
Hi, here you can get it www.pixelfehler-hh.de/Premium-lcd-display-speedo-instrument-cluster-Mercedes-B-Class-w245
Bonsoir, SVP j'ai besoin d'un afficheur de rechange, j'ai le même problème, merci de m'avoir indiqué où je peux le trouver sur le net SVP
Hello, in english iam able to help you.
Lieber Herr!
Bitte hilf mir.
Der Drehzahlmesser unserer B-Klasse W245, Baujahr 2005, lügt. Manchmal zeigt er mehr, manchmal weniger an, aber manchmal bleibt er auf Null und bewegt sich nicht.
Wo soll ich nach dem Grund suchen, warum hpol so viel und so viel anzeigt? Was könnte der wahrscheinlichste Grund sein. Eventuell ein Lötfehler? Oder könnte ein Kontakt defekt sein?
Vielen Dank im Voraus für Ihre freundliche Hilfe!
Mit freundlichen Grüßen, János Bohus
Anfragen bitte unter support@pixelfehler-hh.de