Sasha's XJ Lost its Brakes! Jeep Cherokee front brakes
Вставка
- Опубліковано 1 жов 2024
- Break Bleeder kit: amzn.to/3RbtnAu
Complete Front Brake Kit Jeep Cherokee XJ 1990-1999:
amzn.to/3E8WtsR
Not the kit I used in the video, because I had to get parts quickly from local supplier. I have used these Power Stop Extreme products in the past and have been happy with them. If I had time to wait for shipment, I would order these.
If my videos have helped you save some money , and you would like to give back to the JeepSolid Garage, consider joining my Patreon page!! There's no obligation though. I am happy to help others out, but it does take a lot of my time.
/ jeepsolid
JeepSolid Merchandise: Hats, Shirts, Mugs, etc: / @jeepsolid
👨🔧 A few of my favorite tools 👇
OBD2 Scanner. Must have tool: amzn.to/3arRurY
Pro-Lift 3ton Jack Stand: amzn.to/2RU6rGa
Pro-Lift 6ton Jack Stand: amzn.to/33R9epj
3 Ton Jack: amzn.to/2S5obyJ
Milwaukee 3/8 Cordless Ratchet: amzn.to/39x7WAO
Extendable Socket Wrench: amzn.to/2LJNV2k
1/2" Craftsman Impact Driver. amzn.to/3pvOi5T
24" Breaker Bar: amzn.to/2RnuSNC
Craftsman Torque Wrench: amzn.to/2Wj7JiD
Dewalt 1/4 impact driver: amzn.to/2GYEJ4w
Be sure to get the kit with 2 batteries. You'll be glad you did!
Craftsman 165 Mechanics Tool Set: amzn.to/2GXRlIg
Excellent tool set that will last a lifetime.
Oil filter Wrench: amzn.to/2IbgT9e
Large Capacity Oil Drain Pan: amzn.to/2OjqXjh
Subscribe: / jeepsolid
Follow Me!!
Facebook: / watchjeepsolid
Instagram: / jeepsolid
Twitter: / dale_jeepsolid
Professional inquires from businesses: email me at dale@jeepsolid.com
#jeep #jeepwrangler #jeeprepair
Some of the links provided are affiliate links, where I earn a very very very small commission for directing you to the website. If you make a purchase, it does not increase your cost, but helps me fund my channel. Thanks for watching JeepSolid. I am not a certified mechanic, just a hobbyist who enjoys working on Jeeps. - Авто та транспорт
Just some advice, In most cars, a brake bleeder sequence starts with the passenger rear wheel, the driver rear wheel, the passenger front, and finally, the driver front. However, always follow your owner’s or service manual for the correct sequence.
Brakes are usually bled starting with the wheel that is furthest from the master cylinder and working towards the wheel closest to the master cylinder. This prevents bubbles in the system being forced into pipes towards wheels that have already been bled.
Yes. Thank you for correcting my mistake.
I’m glad you replaced both. Always replace in pairs.
Yes! Thank you
Remember People when doing brakes in your Jeep You will need a welder.😅 Almost everone has notches on the knuckle yokes.
Awesome to pass on the knowledge to children and grandchildren later on. My grandfather was a Diesel mechanic for the Railroad and could tear down tractors and put them back together. But sadly he never passed that onto any of grandkids. My father would only work on his Van or cars if BROKEN.(which meant a day or two) and too busy to have us kids help him.
Yeah, it’s sad when parents are ‘too busy’ to spend this time with their kids. My parents didn’t teach me anything about mechanics. Had to learn it all on my own. But that doesn’t mean I can’t teach my kids! It’s valuable time
@@JeepSolid I agree.... UA-cam and just quick internet search has so much. Trying to get my Son to learn just a little bit each week.
Front and rear are on separate systems. If your vacuum bleeding, I wouldn't think it would matter where you start. Pumping the pedal bleeding???
Separate systems? The lines all come to the same master cylinder
@@JeepSolid front and rear are completely independent. Have been for safety
I have a 1991 jeep Cherokee XJ 4.0 no start done replace almost every sensor today I put on a used ECM off of a XJ just like mine and it still won’t start it started up Sunday but haven’t since new coil new crank sensor still nothing
Not sure what all you have looked at, but I start with Spark and Fuel. Make sure each plug has good spark, then I test fuel pressure. Maybe spray a bit of starter fluid in it to see what it does.
Fuel pressure regulator located inside fuel pump housing or on fuel rail.
Sasha are so cute ❤
wtg Sash!
Thanks
✅️
I didn’t see the link for the brake bleeding tool? Can you post that? I’m needing that tool!
here ya go. amzn.to/3RbtnAu
@@JeepSolid thank you!😀
Sasha are so cute 🤡
I have to a Jeep XJ but ab1993
Thanks
I hate the hard line to rubber connection but always try to do brakes hoses when changing calipers…. But I noticed my 99 Cherokee (picked up last month) had the “notches” in the knuckle too so I guess that I’m going to pull the calipers back off and take care of it next opportunity. Glad to see Sasha involved.
Thanks! Seems like there is always something to do. Haha
Pretty sure the TJ and XJ share the same platform so this would apply to a TJ too. Thanks Dale!
Cool. They are super similar in many ways 👍
I was always told to start at the farthest away from master cylinder to bleed brakes. I will try your thinking next time working on my brakes
Yeah. I believe the correct way is closest first, but I’ve been wrong before. Logic in going closest first is if you do furthest first, but still have some air in a closer line, it can bleed into the further away line . Kinda like sucking on a straw with a hole in it 🤷♂️
@@JeepSolid I agree with your thinking because to me that makes sense
You were correct originally. I’ll be changing my way of thinking about this. Most common to start furthest away. Adapt and learn for me 🤗
@@JeepSolid life is a learning experience as long as we are willing to learn. I'm always learning at age 70.. I enjoy watching your videos
Great job.
Thanks
Disposable gloves 🧤, then she does not worry so much about grease getting on the pads and rotor.
Sometimes I use gloves, but I then worry about touching a greasy part with the glove and then contaminating the pad 🫤
@@JeepSolid use disposable then change them when installing post grease. The harbor freight ones fit tighter, they have different sizes. Just my suggestion.
Dale: Another great video. Nice that your girl is interested in working on cars. Most kids now a days don't even know
how to change a flat tire or care to learn. You need to get Sasha a pair or two of clear safety classes, have her keep one in
her own car. Not a dig, she just needs to learn the right way to work on a car. When she was underneath the car looking up
without safety glasses on UGH.
You sir are totally right 👍 I’m usual really good about safety gear, but totally missed in this case. I guess I wasn’t expecting her to go at it from underneath. I’ll be more attentive next time