ABB TZIDC Positioner Troubleshooting

Basic troubleshooting methods,

[@lakhwindersinghjatyani]

Very good anil keep going👌👌✌️✌️

[@zahidahmad7028]

Sir your video is jabardast hai

[@Rohit-zc2ew]

Woooow sir nice eske parts ke releted aur achha se aur video aur thoda lamba video banaye na sir please,

[@reshmisivagayathri3472]

Amazing sir

[@johnashok9822]

Superb bhaina

[@vinodverma1879]

सर डबल एक्टिंग में 1pot से air आता है और एक pot नहीं आता है

[@instrumentationandsolution5013]

For opening 1port and for closing 2nd port ....so both will be used in double acting actuator....for single acting actuator only 1 port used ..

[@riyasudeendeen5452]

Kala bhai 👌👍👍

[@cv8035]

Very good

[@siddagondkabadagi274]

nice video sir🙏🔥

[@Rohit-zc2ew]

Sir ek baar Siemens positioner par v ek aisa hi video banaye na sir please sir

[@pankajkumar-ct9mk]

Sir mere pass pahle Siemens ka PS2 sipart ka positioner lga hua tha but usme problem aane pr hamare company me valve ke sath ABB ka TZID model aaya to purane Siemens ke jagah pr replaced krne ke baad auto mode me scada se operate nhi ho pa rha hai...Mere hisab se shayad pahle wala me 14 port se but ABB me 6 hi port hai...Pl sir koi solution ho to bataye......Thanks

[@AnilKumar-xo7ot]

What do u mean by 14port or 6port ....it should work ....any how give me u r whatapp number....I will help u

[@instrumentationandsolution5013]

Send me u r whatsapp no ..

[@murugesangk6428]

Display BIN_CTRL What happened.positioner not control only open or full close

[@instrumentationandsolution5013]

Did u checked I/P passing....

[@noorshaikh3361]

On autoCalibration positioner stuck at 50 take long time after that message indicated TIMEOUT. please reply.

[@instrumentationandsolution5013]

Check I/P passing, check actuator passing, check any leakage in output

[@zahidahmad7028]

Hello dear friend there is one resion in abb positinor that when we give comand 0 to 100 then going 0 to 50 direct

[@zahidahmad7028]

Not going 25 percentage going 0 to 50 ,75,100. And 100 to 75,50 ,and when giving 25 not going 50 to direct come 0

[@instrumentationandsolution5013]

Check Parameter -3.0 minimum range should be zero% and maximum should be 100%, and what is the parameter selection of 2.0 and 2.2 ... If possible update me 2.0, 2.2 and 3.0 parameter...

[@kanhaiyamahato9438]

sir ji abb positioner me manual karne
k baad upar bhagta hai aise kyun hota hai. please hame reply dein

[@AnilKumar-xo7ot]

Due to I/P..... plz check the I/P calibration video in my channel

[@sanojkumar-ty3rf]

स्मार्ट पोजीशनर है जो ऑटो में सही काम कर रहा है पर मैनुअल में डालते ही या तो ओपन या क्लोज हो जाता है ,कैसे सॉल्व करे कुछ सेटिंग में हो

[@instrumentationandsolution5013]

You need to do the I/P adjustment.. check my I/P adjustment video.

[@sanojkumar-ty3rf]

@@instrumentationandsolution5013 कोई प्रोग्राम में दिक्कत तो नही है ना

[@sanojkumar-ty3rf]

I/p कही खराब ना हो जाए

[@AnilKumar-xo7ot]

@@sanojkumar-ty3rf may be .. but in manual mode if it is opening or closing them hunting will be there while operating, so in parameters 7 u can increase dead band..

[@gunadharmajhi7699]

Hunting pai kana kari baku badi b... sir

[@instrumentationandsolution5013]

Check any air leakage and actuator passing , check valve operating smoothly and gland tightness, then do I/P calibration .. Check I/P calibration video in my channel

[@gunadharmajhi7699]

Siemens and abb positioner solution kiya hai sir kon konsa parameters isko check kar sakte hai....

[@explorebeforeuexpire8848]

🤝🤝🤝

[@markjason1887]

Hi. Can you make a envlish caption for this video

[@instrumentationandsolution5013]

U need sub titles or anything else...

[@markjason1887]

@@instrumentationandsolution5013 english subtitle

[@instrumentationandsolution5013]

I will try ....

[@waqaskhan2736]

Sir out air from positioner is low.. what is reason??

[@instrumentationandsolution5013]

Check regulator, inlet air filters of positioner, then check pneumatic block ..

[@waqaskhan2736]

Sir regulator pressure is 4 to 5 bar it is ok.. but out air from the positioner is low and valve open just 10 percent.. if pneumatic block is faulty then how can we repair.. plz sir share about it

[@instrumentationandsolution5013]

@@waqaskhan2736 sometimes I/P can create this type problems, so check both once, then u will know which one having issue ...

[@ddhangar]

​@@instrumentationandsolution5013 Air is ok from out1 but when block the hole air from out2 is low and also some air from out1...is I/P faulty?

[@manikandans3624]

Very good

[@theshow2089]

Very good