Відео

Sorry, I never done ... and right now, I didn't have that positioner to check ..

Best practices are to give external air supply to actuator and open 50% and at that time, the positioner feedback link should be (horizontal -----------------)

If double acting actuator then check actuator passing and remove spool clean it and refix it....check the gasket once

If there is any error, you need to rectify that 1st ...

Check the polarity once and remove one wire and check voltage in series, then you will know any problem with PCB ....

I will try ...thq u

Only you can adjust realy in 6200, other smart positioner having different options for little adjustments...ABB I/P can be adjusted... need to go through those instruments..

Both are totally different 1. Volume booster used for large actuator for quick response or speed operation. (can be used in the control valve as well as in on/off valves ) 2. SOV are used for operating on/off valves and in some applications used to block the path (safety interlock)

Thq you

Keep positioner operating mode to 1.1 .. Check the feedback cable and current mA cable once ... Sometimes cable can be interchanged ...

@@instrumentationandsolution5013 checked in 1.1 it's working fine and also able to operate in local mode. Only in remote mode it's not operating. ps. it's a profibus PA device

Check the address in the positioner ..

I never used and zero sigma values are used for uneven/bad installation, vibration, air/gas bubbles in flow tube...

Multi gas analyzer lagana hai Bhai ... Wo bohut costly hai... Pollution is going to increase everywhere 😔😔😔😔....

Positioner output is not accurate as per a given signal ... So the controller checks given signal vs output or outcome of the signal ...

The unit can be changed in basic setup or detailed setup,

May I/P having issues... Check and Calibrate I/P... U can check my I/P checking and calibration Video once ...

@@instrumentationandsolution5013 I try use reset, still can not use . Always run 20 outlet no have any air come out

U can adjust I/P... Plz check my I/P adjustment video...

If the flow tube is empty then sometimes the flow transmitter shows values.. earthing.. and external induction... Or flow converter/ transmitter having issue

Thank you sir for your valuable information 👍👍👍👍👍❤️❤️❤️

What do you mean by S N..?

Serial Number kaise Change hoga pls sir

Not going 25 percentage going 0 to 50 ,75,100. And 100 to 75,50 ,and when giving 25 not going 50 to direct come 0

Check Parameter -3.0 minimum range should be zero% and maximum should be 100%, and what is the parameter selection of 2.0 and 2.2 ... If possible update me 2.0, 2.2 and 3.0 parameter...

U can do a manual stroke check with the local buttons ... It's very easy... Through hart also u can simulation.. if the positioner has any issue then it will not operate ...

Check the zero trimming option, before doing zero ensure the outlet valve should close properly and the flow tube should be filled with process fluid...

If Spool is having issues, u will get an error then you can clean the spool, dead angle linearization never done .. need to check once ..

AO feedback?

Out of range means ? .. positioner pot having issues or positioner mounting issue... Need to find out the exact issue..

What is the problem..

Working manual but not working with 4-20ma.

U can't replace it with normal DCV ...I left that company, unable to show you wiring connection,

While installing a new positioner or maintenance problem or you want to change it

Sir aap density transmitter par video banaye na please

Check angle once.. at 50% valve opening angle should be 0.... so u can adjust feedback angle with POT. Then again go for auto cal

Four zeros... 0000.. normal password for quick setup ...

Hart type

I never did with hart ... If it's communicating then u can start the simulation with changing DIP switch position according to positioner model ...

You need to check in the field..remove installed one and fix the repair one .. this is general practice.. some companies can provide a test bench for troubleshooting ...

I never did that .. but exactly what you want to do ...

কোন পাল্স এর কথা বলছেন

You need to do the I/P adjustment.. check my I/P adjustment video.

@@instrumentationandsolution5013 कोई प्रोग्राम में दिक्कत तो नही है ना

I/p कही खराब ना हो जाए

@@sanojkumar-ty3rf may be .. but in manual mode if it is opening or closing them hunting will be there while operating, so in parameters 7 u can increase dead band..

PT1000 RTD used for cold junction compensation, u need to put atmospheric temperature ( the resistance value around 1110 to 1120 ohms)

Did you checked feedback adapter tightness and POT resistance, issue may in feedback part....check properly once again ...

How can I help you...