Mass transfer pendulum. Drive system with pendulum mechanism, Patent pending
Вставка
- Опубліковано 11 жов 2024
- For more information or program for Arduino you can email me: cmsscorpllc@gmail.com
Possible applications: Pumpjack, energy storage, power swing………….
Currently existing Pumpjacks are typically powered by electricity from fossil fuels generators. In the classic old style Pumpjack, a big and powerful electric motor uses all its energy to spin heavy weight which moves an artificial lift to pump crude oil from underground reservoir. In my design, there is much smaller electric motor which would be powered by renewable energy.
The advantages of the new design compared to the old style Pumpjack are:
-Utilizing gravitational potential energy of a pendulum instead of generating all mechanical energy with a massive electric motor.
-Much lower energy consumption powered by renewable energy, no need for fossil fuel generators.
-Lower cost to manufacture and transport. -Lesser amount of parts, only a few moving ones.
-Simple design, easy to assemble in site.
-Low maintenance.
Energy storage.
Electric motor on Pendulum will start running during off peak times like at night or during the day while solar panels are producing more electricity. After reaching the highest position, pendulum will lock in place and motor stops running. System will be in standby mode. Then, whenever needed, pendulum gets released and starts functioning as a power generator.
PARTS:
Microcontroller Arduino:
ELEGOO UNO R3 Board ATmega328P... www.amazon.com...
Reed switch:
4 pcs/Set Reed Switch Normally... www.amazon.com...
Relay module:
HiLetgo 12V 8 Channel Relay... www.amazon.com...
Display:
DORHEA 3PCS TM1637 0.56" 4 Bits... www.amazon.com...
Limit switches:
5PCS ME-8108 Momentary Limit... www.amazon.com...
Stones:
www.homedepot....
Ball screw:
CHUANGNENG Ball Screw CNC Parts... www.amazon.com...
Motor:
WMYCONGCONG DC 12/24V 30W High... www.amazon.com...
Pillow blocks:
PGN UCF204-12 Pillow Block Bearing - Pack of 2 Square Flange Mounted Pillow Block Bearings - Chrome Steel Bearings with 3/4" Bore - Self Alignment
a.co/d/3ckAENP
SAME PRINCIPAL CAN BE USE ON A WHEEL. GOOD JOB!
Good idea with the wheel, i thought about too but unfortunately this pendulum or playground swing works like “mass transfer moving lever” and it cannot work on wheel. But what could work is spinning mass instead of sliding back and forth which would require less input energy.
Even as a child, I wondered how I could make the swing go, simply by "pumping" my legs and upper body back and forth.
Your next step would be to put the entire apparatus on the swing, and have it sense like a four year old can. Then get Boston Dynamics to get their robot to play on a swingset.
Great idea with Boston Dynamics robot. But it would probably take them like 1 million hours to make a program for it.
It’s funny how we were all told at school by physics teacher that swing is “pumping”. If you google it now, still all educators and scientists claim that swing is pumping. But it’s NOT, it is a mass transfer like you can see here. Funny thing is when we realize that all educators, intellectuals and scientists were wrong about swing but they are certain about what was happening one nanosecond after Big Bang.
Every electronic engineer worth his/her salt, will recall the mode of operation of a class C amplifier, and the concept of "angle or circulation" - which underpins the kind of device designs where the input is present only for a fraction of time, and at the precise time when the new and the pre-existing energy in the load do sum together...
Nice build and very impressive demonstration with a real proof of concept
Can you power your device with several solar panels ?
Energy is added to the system on every stroke.
Starting energy is not from zero as the designer pushes it against gravity before starting.
Therefore the energy multiplication is not as stated.
Better method for energy transfer is to obtain a watt meter for the motor controller. Then measure speed at dead centre on the bottom of the pendulum movement. Measure total watts over all the strokes until momentum has built up, then measure the speed, o.5 mv2 for kinetic energy output. Now calculate energy multiplication.
Btw, start it without any push.
Great point. Btw, Pendulum can start without any push no problem. You can see that on video 1:42 in manual mode. I’m starting from small angle only because microcontroller needs to calculate period and timing in automatic mode. Energy of the system is not accumulated. If it was than you would do many strokes with small weight to get one big stroke of the whole pendulum. You can see that one stroke of a small weight on linear slide equals one stroke of the whole pendulum. Energy of the system comes from mass, not gravity. As we all know, mass is energy and gravity here is just a middle man.
At least you should have noticed that the electric slide always travels the same distance, the pendulum amplitude increases (very slowly) with time.
I let you think a little on how the pendulum can reach such increase of energy and where that energy is coming from.
Ah, I guess that, by now, you already noticed the futility of having a display of the period of a pendulum IN REAL TIME. Yeah, you could have skip that, don't you think?
Nice efforts
Well done !
Nice. But the timing and speed of your moving weight must better.
Anyway i had the same idea.
The wondering on a playground with simply pushing the legs back and four move mega Mass.
Nice job CMSS - clean build - next step is to self loop and remove the power supply.
Wingnut 🙄
What happens if you add a shake weight for extra degrees of freedom/resonance?
Yes, good point, I tried it, even rubber bands on moving weight with wheels. It didn’t improve the performance.
great, beautiful work
Thanks
hi. Where in this mechanism will there be the highest torque output for the generator?
At pendulum equilibrium point, bottom middle. It’s fastest there.
@@cmss5674 I had the idea of a bicycle ratchet, on each side on the upper axis of the pendulum, inverted, connecting an exion with a crown with current.... a home-made wind turbine stator, more efficient, for me. Good talk to think about
@@cmss5674 It seems to me... that you have the idea of a linear generator
Once the movement of the weight stops.... it should go backwards only wen the movement of pendulum is reversed. if you do that you have less losses.
Good point, that’s how I originally started in the beginning but that movement backwards would generated small push on pendulum opposite way and slow down the pendulum. That’s why I had to change timing to what it is right now.
@@cmss5674 I believe the reason is because and in "theory" the wheight once it starts the movement it must virtualy be from the midle to oposite and versus. the inercia than should cancel itself. from other hand the masses interact each other, and wen the pendulum wen is on steady state momentum, any movement from weight will react. you tried to do fast movement on weight? or progressive like we all do on play swing chairs? NICE WORK
Детские качели..... Мужик в детство ударился.
Clearly over unity!
go to a constraction side where a big cran is operating. Have a good look how they operate the mass. Ask the cran operator why he act like he do and what he never would do. You will go home with same new idees I am sure.
❤