Perfect timing on the mounts. I have to do the same thing to a craftsman saw this weekend . Need to make tool for it . Thank you . Peace and love from Wisconsin .
Good video. My new 61 carcass is pre 1982 my tank has brass Bush the rubber mounts thread in to 4 out 6 spin in the plastic. Then the oil cap is smaller then all my other 61 husqvarna. I contact Berry chainsaw shop on Ebay and he had the oil cap. But anyway I was going to swap tank and Tinman put it on video. Thanks Tinman.
Very good how to tutorial. I enjoyed it a lot. I thought about you today while rolling around under my truck, checking to see how hard it will be to replace a busted brake line over the gas tank. I'm going to get a roll of NiCopp tubing and fittings tomorrow.
Love the way you make do, n mend/improve 👍 could you cut/grind a old socket to make two prongs. Help give more feel on the AV mounts. Thanks for sharing
Hello tinman..i feel your pain with those triggers, fiddley no doubt...word to the wise stay clear of cheap mounts and cheap replacement tank handle for 61& 266 adds extra frustration to eventually end up in the rubbish...
Thank you for explanation..If the oil leaks from the oil pump and constantly leaks under on the AV rubber buffers...Does it destroy the rubber buffers ??
What good to stiffen up these bushings or to save them is automotive Goop really stiffens up those bushings makes them take the longer bars mahalo,ALOHA! 🤔🤙🏾😎
Hey tinman how’s it goin? Just a question buddy…… 625ii and 630 J’red I have one of each both have different intake manifolds….. my 630 intake block is cracked and warped I cannot find a replacement on ebay etc and my 625ii needs a carby but I cannot find the correct one of those either🤷♂️
I'm new here just subscribed. Watch all of Buckin' Billy Ray all the time .I have A SE266 the year 1984 and it needs mounts are the mounts hard to get? And I have A 272XP are the mounts interchangeable with those saws. Like you were saying my 272 will not buck up cuts got to be mounts on it to.
hey tinman, i have a 262 xp in my shop and the clutch is really hard to get off. i did a piston stop with rope. and she dont wanna cooperate even with a longer bar. expecting wd-40 or penetrant oil. do you have any tricks for these models ?
I changed out all the av mounts put it back together and there still a vibration on the back trigger hadle on my 630 more than what's on my 630 super can not figure it out
Perfect timing on the mounts. I have to do the same thing to a craftsman saw this weekend . Need to make tool for it . Thank you . Peace and love from Wisconsin .
GREAT JOB TINMAN ,LIKE HOW IF YOU THINK THE PART ISNT GOOD YOU JUST CHANGE IT,,NO HESITATION ,,PREVENTIVE MAINTENANCE
Good video. My new 61 carcass is pre 1982 my tank has brass Bush the rubber mounts thread in to 4 out 6 spin in the plastic. Then the oil cap is smaller then all my other 61 husqvarna. I contact Berry chainsaw shop on Ebay and he had the oil cap. But anyway I was going to swap tank and Tinman put it on video. Thanks Tinman.
Love the real time video which includes the minor mistakes and rethinks. Shows your human like the rest of us Tinman.
good timing tinman I'm swapping a husky tank later this week. Tree fell on the old 1
Very good how to tutorial. I enjoyed it a lot.
I thought about you today while rolling around under my truck, checking to see how hard it will be to replace a busted brake line over the gas tank.
I'm going to get a roll of NiCopp tubing and fittings tomorrow.
So good... Very nice work Tinman. Nothing's done until it's perfect!!
U tell uncle harve we miss story time!
Love the way you make do, n mend/improve 👍 could you cut/grind a old socket to make two prongs. Help give more feel on the AV mounts. Thanks for sharing
My 268 needs new mounts this was so helpful 👍🏻
Thanks for the tips, starting on a 272 in the morning!
Hey Tinman, love these series of saws!ALOHA from Maui! 🤙🏾😎
SURE APPRECIATE YOUR WORK MR TIN MAN
THNX BUDDY.
Where do you source your av mounts?
Hahaha nicer the clothes worser the breakdown love it going to use it. Your attention to detail is great thanks and more please
Great work, Tinman! I continue to learn a ton of great stuff from you! 👍💪
Thankyou for being here. Sharing knowledge is 100% my mission on this channel.
@@tinmanssaws love to see it! Without you and harv i would have never port a power saw.
Hello tinman..i feel your pain with those triggers, fiddley no doubt...word to the wise stay clear of cheap mounts and cheap replacement tank handle for 61& 266 adds extra frustration to eventually end up in the rubbish...
Good vibrations, do you feel them a bit more with the stiffer mounts? Time to show a cutting video of that thing.
Thank you for explanation..If the oil leaks from the oil pump and constantly leaks under on the AV rubber buffers...Does it destroy the rubber buffers ??
Good Man Tinman, excellent video
Hey Jack good to see here buddy.
Great info in this vid. Be safe and be careful.
Where did you buy the mounts at?
What good to stiffen up these bushings or to save them is automotive Goop really stiffens up those bushings makes them take the longer bars mahalo,ALOHA! 🤔🤙🏾😎
I AM DIGGIN THAT MUFFLER
how would i go about getting a set of those felling dogs that you got on that 266xp?
Hi nice vid .need to watch this 1 again a lot to take in for me . Thanks
Great video man 👍👍👍
💪 keep up the good work Tinman!
Thanks tinman.. i have the exact issue on a saw at work.. its a 268 i believe.. but it dont have the xp?
Hey Tinman ur videos are great!👍
Nice job tinman. Always working on something different. Really makes a man well versed in his craft. By the way sr do you work on old model47 macs
Thanks for sharing
Thanks for the info, Tinman!
I much prefer getting sprayed in the face by Stihls than leaking fuel on the bench from cracking the cap. Wait... no... no in don't!
Hey tinman how’s it goin? Just a question buddy…… 625ii and 630 J’red I have one of each both have different intake manifolds….. my 630 intake block is cracked and warped I cannot find a replacement on ebay etc and my 625ii needs a carby but I cannot find the correct one of those either🤷♂️
The jonsered 630 takes the same intake block as a 266
Did you see husqvarna released some videos of the new 592 and 585? I think I'm in love. 592 for me. If anyone can get hands on one early let me know.
I'm new here just subscribed. Watch all of Buckin' Billy Ray all the time .I have A SE266 the year 1984 and it needs mounts are the mounts hard to get? And I have A 272XP are the mounts interchangeable with those saws. Like you were saying my 272 will not buck up cuts got to be mounts on it to.
Welcome, Dan!
Welcome...are they fine thread for metal tank can be difficult to get a complete set...
@@nickywalsh8492 Thanks . The tank is plastic . Like Tinman's said they gust keep running well my saw's need TLC now!
@@jeffreyrubish347Thank you..
Welcome Dan!!
The dogs are fabolous :)
As far as nice clothes, having none that are not stained or perforated from welding splatter, you me same! Lol
hey tinman, i have a 262 xp in my shop and the clutch is really hard to get off. i did a piston stop with rope. and she dont wanna cooperate even with a longer bar. expecting wd-40 or penetrant oil. do you have any tricks for these models ?
do you happen to know what the part number is for the Husqvarna 2100 CD buffer mounts? are they all the same?
Thanks Tinman for the awesome videos
501269704 is the number I came up with. Hope that helps
@@tinmanssaws bless your heart kind sir
I bought the "tools" little slotted metal pieces. They make a good pattern but are too soft. better off making them. I like your pliers.
I made a tool out of old deep socket, took alot of tinkering but works great,
Thats a good idea
IT SUCKS I HAVE TWO THAT DO THAT .
Another good reason to run a short bar, just doesn’t look as cool! 😜
This is the same chassis as a 630 ?
Yes 630 and 266 are the same
I changed out all the av mounts put it back together and there still a vibration on the back trigger hadle on my 630 more than what's on my 630 super can not figure it out
as time goes by you need to have a stiff bar
Hey bill...how are you ....
all ok not great
@@nickywalsh8492
She’s a 52mm 75cc eh?
Bán cho mình cái bình xăng lớn đi bạn
Hi what kind of needle nose pliers are those?