Great vid and great tip about loosening the fill plug first...draining it and then being unable to get the fill plug off--classic kind of problem I'd run into.
Thanks for doing this video. I just did mine today (2016 Patriot). I didn't have to rig a 90 degree elbow, I just came in with the tubing (1/4" ID x 3/8" OD clear tubing) from the left side between the cross member (behind the drive assembly) and the drive assembly, and I was able to bend the tubing so it entered the fill hole. I pumped in the fluid (a little less than 600 ml) without an issue using one of the pumps that screws into the top of the 80w90 quart size containers.
Thanks, helped my 12 year old mechanic find the fill plugs that Jeep should paint red. 80-90 standard gear oil - what a surprise that they didnt use a 15$ a quart exotic fluid.
Hi pal, great video. Wondering if you could give any advice. I bought a 2011 patriot 2 months ago and have noticed it leaking fluid from RDA but not at the seal where the drain is but the one further up. Is it safe to open it up there to re seal it? Or will it just need the bolts tightening? Any advice would be great. 👍🏻
That's outside my realm of expertise. Personally, though, what you’re describing is definitely not something that I would try to fix on my own. I would be looking to the pros on that one. Sorry I couldn't help more than that.
There aren't any specific capacities mentioned and there is no level indicator, so you want to make sure that it has enough fluid. By filling it until it overflows amd then letting ot drain, you know what the level is. You could use other methods to ensure the level, Im sure. This was easiest for me.
@@harleyrider883 do you think a quart is enough for both? The RDU started dripping out, but the ptu didn’t start dripping out before the quart was empty, I prob put in a little less than a half a quart
I agree with the standard gear oil in the rear, but I thought the front unit took an exotic synthetic? What is your research show? Also you changed new fluid. Did you out the wrong one in previously?
Your manual will show what oil to use -- and they're the same for both ends. I just wanted to have the same oil in both ends and couldn't get more of the same for the front, so just changed it again in the back. That also allowed me to make the video, so I didn't mind. Good luck with yours!
Your Owner's Manual will tell you what oil is required for the particular year and model you have. If you don't have a manual handy, they're available on line. My manual said 75W90 for my 2011 model but my 2015 was 80W90.
@@harleyrider883 Hi, I have the manual but it don't write anything for oil at gear differential. Only for engine. I have the Jeep Compass 2.0 Crd 4X4, 2007 Model. Thanks mate for your advice...keep going the good work!!!
This should bring you to the link for the manual. It appears to be on page 364 under the section for maintenance Schedule. Here's a link: www.mopar.com/jeep/en-us/care/owners-manual.html?openGarage=true
Niall Halvey The owner's manual indicates SAE 80W-90 AGL CL 5 gear lubricant. It costed me about $6 or $7 for a jug and one jug was more than enough for both the front and back. Since your vehicle is undriveable without the fluid, though, I'd make sure that you have an extra jug just in case something surprising happens. As for the transaxle question, I think that the answer is "no" , but that's going beyond my expertise. Here's a link to an article that you might find interesting : www.carid.com/articles/transaxle-vs-transmission.html
I didn't go with Mopar just because they were closed when another retailer was still open. As long as it meets the specs set out in your owner's manual, you'll be fine.
khaldon ibrahem : The oil breaks down over time and stops providing the protection that the gears inside the assembly require. If that happens, you can end up shortening their lifespan and incurring expensive repairs. Your vehicle's owner's manual will identify how frequently it should be changed. The good news is that it doesn't usually have to be done before something like every 80,000 km.
harleyrider883 i had a problem of whining sound coming from the RDA ,I thought that maybe the problem is the oil ,and I change it today but the same sound still , first i thought the sound coming from the tires bearing because it is the same sound when u have a bad bearings . Is there a solution for this issue ? Thank you
khaldon ibrahem : That doesn't sound good. I had a vehicle that lost its gear oil once due to a leak and the sound was grinding and rattling. Bearing issues have usually sounded to me like a higher pitched whirring sound. I would bring it to a service centre and get them to look at it -- too hard to tell otherwise!
tyler serich It's about 600 ml as I recall. What you do is you keep pumping it in until it starts to overflow. It's impossible to overfill unless you take absolutely extraordinary measures. I'd buy two quarts just to be safe for the first one and then a third to have more than enough for the second unit. Better to have too much than to have an undriveable vehicle when you need to get back to NAPA to get another quart! Good luck to you...
Great vid and great tip about loosening the fill plug first...draining it and then being unable to get the fill plug off--classic kind of problem I'd run into.
Haven't we all been there (about a hundred times!) 😉
Thanks for doing this video. I just did mine today (2016 Patriot). I didn't have to rig a 90 degree elbow, I just came in with the tubing (1/4" ID x 3/8" OD clear tubing) from the left side between the cross member (behind the drive assembly) and the drive assembly, and I was able to bend the tubing so it entered the fill hole. I pumped in the fluid (a little less than 600 ml) without an issue using one of the pumps that screws into the top of the 80w90 quart size containers.
Well done! Glad it worked for you.
Thanks, helped my 12 year old mechanic find the fill plugs that Jeep should paint red. 80-90 standard gear oil - what a surprise that they didnt use a 15$ a quart exotic fluid.
This is by far the best video I've found on this subject. Thank you.
Thanks! Glad you found it helpful.
really nice video. thanks for taking the time to shoot the video for every body.
Very helpful. Thanks a lot.
hey good video and down to earth instructions.
Excellent by far
Great video! thank you for sharing knowledge.
Thanks! Hope it helped!
Thanks for share this video
Did you ever make the video for the front?
It's up now . . took a while!
it is motomaster gear oil 80/90 non synthetic can work? it is gl5 conforme
Hi pal, great video. Wondering if you could give any advice. I bought a 2011 patriot 2 months ago and have noticed it leaking fluid from RDA but not at the seal where the drain is but the one further up. Is it safe to open it up there to re seal it? Or will it just need the bolts tightening? Any advice would be great. 👍🏻
That's outside my realm of expertise. Personally, though, what you’re describing is definitely not something that I would try to fix on my own. I would be looking to the pros on that one. Sorry I couldn't help more than that.
harleyrider883 no worries friend. Thanks anyway.
dosent it take a half of quart? why would you pump it too the top untill it drains from the top.
There aren't any specific capacities mentioned and there is no level indicator, so you want to make sure that it has enough fluid. By filling it until it overflows amd then letting ot drain, you know what the level is. You could use other methods to ensure the level, Im sure. This was easiest for me.
great video make more I'll subscribe
also ware do i apply the red locktite?
I don't use it. You may need access to it again some day.
Should you wait until the new oil stops dripping out before closing it or close it while it’s drilling? Thanks
I'd wait until it's done. That way you know for sure that the level is below the opening, reducing the likelihood of a leak.
@@harleyrider883 do you think a quart is enough for both? The RDU started dripping out, but the ptu didn’t start dripping out before the quart was empty, I prob put in a little less than a half a quart
It ran me somewhere about 600 ml, or just over half a quart
Sounds like you've got it going right!
I agree with the standard gear oil in the rear, but I thought the front unit took an exotic synthetic? What is your research show?
Also you changed new fluid. Did you out the wrong one in previously?
Your manual will show what oil to use -- and they're the same for both ends. I just wanted to have the same oil in both ends and couldn't get more of the same for the front, so just changed it again in the back. That also allowed me to make the video, so I didn't mind. Good luck with yours!
Which is the oil type for rear gear differential ?
Your Owner's Manual will tell you what oil is required for the particular year and model you have. If you don't have a manual handy, they're available on line. My manual said 75W90 for my 2011 model but my 2015 was 80W90.
@@harleyrider883 Hi, I have the manual but it don't write anything for oil at gear differential. Only for engine.
I have the Jeep Compass 2.0 Crd 4X4, 2007 Model.
Thanks mate for your advice...keep going the good work!!!
This should bring you to the link for the manual. It appears to be on page 364 under the section for maintenance Schedule. Here's a link: www.mopar.com/jeep/en-us/care/owners-manual.html?openGarage=true
@@harleyrider883 Thanks again !!! You are very helpful !
Hi, what spec of fluid did you use . Is this area also known as the transaxle ?
Niall Halvey The owner's manual indicates SAE 80W-90 AGL CL 5 gear lubricant. It costed me about $6 or $7 for a jug and one jug was more than enough for both the front and back. Since your vehicle is undriveable without the fluid, though, I'd make sure that you have an extra jug just in case something surprising happens. As for the transaxle question, I think that the answer is "no" , but that's going beyond my expertise. Here's a link to an article that you might find interesting : www.carid.com/articles/transaxle-vs-transmission.html
@@harleyrider883 i bought the motomaster 80/90 non synthetic is that work well
Do you have a video doing the PTU?
Thomas Brendel I haven't managed to put it together yet, but it's quite straightforward . I'll try to pull it together soon!
harleyrider883 do you use Mopar fluid or something else?
I didn't go with Mopar just because they were closed when another retailer was still open. As long as it meets the specs set out in your owner's manual, you'll be fine.
The PTU video is up now if you're still interested.
Why do you replace the oil?
khaldon ibrahem : The oil breaks down over time and stops providing the protection that the gears inside the assembly require. If that happens, you can end up shortening their lifespan and incurring expensive repairs. Your vehicle's owner's manual will identify how frequently it should be changed. The good news is that it doesn't usually have to be done before something like every 80,000 km.
harleyrider883 i had a problem of whining sound coming from the RDA ,I thought that maybe the problem is the oil ,and I change it today but the same sound still , first i thought the sound coming from the tires bearing because it is the same sound when u have a bad bearings . Is there a solution for this issue ? Thank you
khaldon ibrahem : That doesn't sound good. I had a vehicle that lost its gear oil once due to a leak and the sound was grinding and rattling. Bearing issues have usually sounded to me like a higher pitched whirring sound. I would bring it to a service centre and get them to look at it -- too hard to tell otherwise!
How much fluid does thw RDA and PTU take?
tyler serich It's about 600 ml as I recall. What you do is you keep pumping it in until it starts to overflow. It's impossible to overfill unless you take absolutely extraordinary measures. I'd buy two quarts just to be safe for the first one and then a third to have more than enough for the second unit. Better to have too much than to have an undriveable vehicle when you need to get back to NAPA to get another quart! Good luck to you...