So it still moves? If it doesn't move check batteries...try new ones cos sometimes it takes more power to run. Also check that your bot is not upside down.
Does anyone know, will the Hexbug BB controllers take Full 1S voltage at 4.2Vdc? Is it possible to run a small USB charging BMS board and 3D print a extended lower controller case?
I did but I wasn't sure which channel. It's because I paired the same bot with a different controller. I label them now so it's easier to recognise. If you find that you are controlling the same bot, do a resync. Pretty much take your bot and controller to another room and pair them again.
I need an answer to this question why do my hex bug bots turn themselves off and my rotator hits the wall when the weapon is on and it doesn’t move then it turns off like how do I fix this
Maybe the battery has come loose after it hit the wall? Also you can check to make sure it's not upside down. I've found that if a bot is upside down, it doesn't receive well.
@@LetMeFixIT I made the battery cover tight so it can’t be loose and it’s not upside down like it’s fine when it’s not spinning but when it is spinning I will click forward or any button on the controller except for the weapon and It will go but won’t stop till it hits the wall then won’t move until you get the weapon off the wall or it will just turn off
Ok so first make sure you've removed the battery tab. Then make sure you've also removed the tab from your remote. Make sure you then put the controller near the bot. If you are doing all this, there are a few things that might have gone wrong. 1. Batteries. Make sure they're fresh. You might have old batteries or they might have been knocked out of place. 2. Make sure you pair them on different channels. If you have, make sure the IR sensor is facing up so it can sense your controller. If you've checked all these things already, make sure you have used to correct controller! Duck only works with the duck controller. Duck's controller has 2 weapon buttons.
@@willpratt8608 Ours was actually an easy fix, I think. We just replaced 1 battery in Tombstone and that seemed to do it. My guess once the weapon was triggered it didn't have power enough to run the weapon and receive a signal.
I don't have a minotaur but when you try to spin it, do you hear the motor's sound whirling? If so, maybe the piece that's attached to the weapon is loose or broken.
@@Jaxifire522 check to make sure your batteries are full. Flat batteries causes the symptoms you describe (as well as other stuff) but check this first.
Hi, My Tombstone battlebot stops working after it hits something. How would I be able to fix this problem?
So it still moves? If it doesn't move check batteries...try new ones cos sometimes it takes more power to run. Also check that your bot is not upside down.
Have the same issue. Have you figured it out?
Does anyone know, will the Hexbug BB controllers take Full 1S voltage at 4.2Vdc?
Is it possible to run a small USB charging BMS board and 3D print a extended lower controller case?
Have you had any issues with Channel 2 & 4 controlling the same bot?
I did but I wasn't sure which channel. It's because I paired the same bot with a different controller. I label them now so it's easier to recognise. If you find that you are controlling the same bot, do a resync. Pretty much take your bot and controller to another room and pair them again.
I need an answer to this question why do my hex bug bots turn themselves off and my rotator hits the wall when the weapon is on and it doesn’t move then it turns off like how do I fix this
Maybe the battery has come loose after it hit the wall? Also you can check to make sure it's not upside down. I've found that if a bot is upside down, it doesn't receive well.
@@LetMeFixIT I made the battery cover tight so it can’t be loose and it’s not upside down like it’s fine when it’s not spinning but when it is spinning I will click forward or any button on the controller except for the weapon and It will go but won’t stop till it hits the wall then won’t move until you get the weapon off the wall or it will just turn off
Neither my duck or my rotator are connecting to the controller no matter what I do how do I fix this?
Ok so first make sure you've removed the battery tab. Then make sure you've also removed the tab from your remote. Make sure you then put the controller near the bot.
If you are doing all this, there are a few things that might have gone wrong.
1. Batteries. Make sure they're fresh. You might have old batteries or they might have been knocked out of place.
2. Make sure you pair them on different channels. If you have, make sure the IR sensor is facing up so it can sense your controller.
If you've checked all these things already, make sure you have used to correct controller! Duck only works with the duck controller. Duck's controller has 2 weapon buttons.
Our Tombstone weapon won't turn off once it's activated. It also won't move after the weapon is activated. Any ideas?
Same
@@willpratt8608 Ours was actually an easy fix, I think. We just replaced 1 battery in Tombstone and that seemed to do it. My guess once the weapon was triggered it didn't have power enough to run the weapon and receive a signal.
@@Afcrowell Sometimes a low battery can cause devices to do wierd stuff like turn on or randomly do things.
my minotaur's weapon won't spin, even after changing the battery's. what do I do?
I don't have a minotaur but when you try to spin it, do you hear the motor's sound whirling? If so, maybe the piece that's attached to the weapon is loose or broken.
my hypershock doesn’t turj on what should i do
@@LetMeFixITpls do a tear down on biteforcw I beg u
I have rotator and even though he is right side up he will still drive uncontrollably
Also my tombstone only does 2 spins and won’t turn off
@@Jaxifire522 check to make sure your batteries are full. Flat batteries causes the symptoms you describe (as well as other stuff) but check this first.