I feel like I just hit gold. Thank you for the great video. I’m collecting info and soon will be collecting parts to do my Baja conversion to a j-series. I will email you soon as I get the ecu to pay you to modify it:)
Just curious does vtec work without a speed signal? Or is there a way to reprogram the Ecu to make it work with out vtec? Also do you break the immobilizer off in the Ecu ? I just picked up a sand rail with a 3 rib bus trans in it and I’m getting a j32a2 for it tomorrow for a deal. Pretty excited to build it. Thanks for the great video by the way, it’s really not too far off from the process of thinning a ls harness to run as a stand alone.
Hey man, I don't know if you'll see this but I need to pick your brain. I picked up a harness for a 1999 odyssey harness with a 1999 TL ECU I'm modifying into my miata and I have a few questions. 1. I cut all the transmission wires but I have 2 yellow and black going to the power junction that are free, do these go to anything transmission related? 2. I have a wire that's brown and black close to I think goes into connector B (3 guides) it has a another wire spliced into it that I've removed but I'm not sure what goes to it.
Hey bro, I did everything I should do on my harness injectors, and coil packs have power just know pulse how do you get that back and I even tried to wire up the immobilizer on the E plug no change can you please tell me what I’m doing wrong
I didnt have it to begin with when I first built the harness I recently just added it to see if that would help get me a pulse to the injectors and coil packs, but I got the same results very confused on where I went wrong
I did. Which lead me to you. Was just hoping you could verify if those were the right pins on connector b to put switch 12v to for ignition switch since the video doesn't actually say where the 2 ignition wires come from just that there's 2
Thanks for the video! I'm curious, if I am using an ECU from an auto trans, does anything additional need to be done to the ECU to allow the motor to function normally? Thanks!
Have you ever messed with a Honda C27? I acquired one in a trade for some buggy stuff and it already has a brand new Kennedy adapter setup so I was thinking about throwing it in my rail but I’m not sure what to do about the harness?
C series stuff is really outdated, youd need a aftermarket ECM and there not much support for that platform, Most people I know with the are swapping to J series
Great content. 👍 looking at getting into dune buggy/ trail buggy..here in idaho. I have an 00 odyssey j35 as my donor. I will pull everything I need and send a pcm to you, I own a small mechanic shop and can do the wiring. Just not modify pcm. Thanks agian
ok got a question, I have a vw baja, looking for a new trans and power plant. should I got ls? or one of these j35 engines? it is set up for mid travel right now.
Thank you for posting this video. I've been looking for videos like this and haven't found many. Can you please tell me if this would work for a j30 and a AEM standalone? I do have wiring experience but I've never done this before and want to make sure it will work before I purchase it. Thank you.
I could but it's like giving out the recipe of the secret sauce...lol, If you know your way around a honda ECU it's not that hard, also I don't wanna show how to remove the Immobilizer. Makes it easy to steal a car, if you need help with a specific project send me a PM
@@duneaddict thats fair. ;-) I am new to this honda J world and am trying to learn all I can. My application is similar to a sandrail but in a rock crawler.
I feel like I just hit gold. Thank you for the great video. I’m collecting info and soon will be collecting parts to do my Baja conversion to a j-series. I will email you soon as I get the ecu to pay you to modify it:)
Just curious does vtec work without a speed signal? Or is there a way to reprogram the Ecu to make it work with out vtec? Also do you break the immobilizer off in the Ecu ? I just picked up a sand rail with a 3 rib bus trans in it and I’m getting a j32a2 for it tomorrow for a deal. Pretty excited to build it. Thanks for the great video by the way, it’s really not too far off from the process of thinning a ls harness to run as a stand alone.
Where can I find ecu diagram???
I sent you a PM on Instagram. I have a question about putting j35a6 in a sandrail didn't know if you could do the harness for standalone
Hey
Yo
Will it have any check enginecode ??im trying to meet emission on mine
how much and who modifies the computer for standalone and thank you for showing this to the world
I do send me a pm..
Hey man, I don't know if you'll see this but I need to pick your brain. I picked up a harness for a 1999 odyssey harness with a 1999 TL ECU I'm modifying into my miata and I have a few questions.
1. I cut all the transmission wires but I have 2 yellow and black going to the power junction that are free, do these go to anything transmission related?
2. I have a wire that's brown and black close to I think goes into connector B (3 guides) it has a another wire spliced into it that I've removed but I'm not sure what goes to it.
Do you need one of the trans speed sensors to read off the crank sensor or is that done internal to the ecu?
I do it internal
How did you side heatshrink on wires... "after" you soldered ? Did you split the heatshrink tube in half?
They were already on and pushed back out of view
@duneaddict anyway u can hip with the transmission codes anything done to the ecu
Hey bro, I did everything I should do on my harness injectors, and coil packs have power just know pulse how do you get that back and I even tried to wire up the immobilizer on the E plug no change can you please tell me what I’m doing wrong
You have to remove the immobilizer
I didnt have it to begin with when I first built the harness I recently just added it to see if that would help get me a pulse to the injectors and coil packs, but I got the same results very confused on where I went wrong
@@hellaratchetek9558 the immobilizer is inside the ecu
OK, thank you so much for the information you provided me
This is the entire harness that goes into the dashboard of a pilot or odyssey right?
There’s the engine harness then there’s this harness?
No this is the engine harness
@@duneaddict thank you, I sent you a PM on Instagram!
Is that a factory ecu
Yes sir
Ok thank you I'm planning on putting a j series in my 95 civic but the wiring harness has got me lol
Hey what wires are actually used to power the pcm? That's not actually covered. I'm assuming pins 1 and 9 on connector b?
Do some research the pinouts are out there
I did. Which lead me to you. Was just hoping you could verify if those were the right pins on connector b to put switch 12v to for ignition switch since the video doesn't actually say where the 2 ignition wires come from just that there's 2
@timelconsumessusdall send me a email hndarcr@yahoo.com
So for a auto trans I assume you keep the auto wires right?
That ECU is reflashed or factory? Can you make a setup like this for a k24 engine and how much would it cost? Do you have a website?
Its factory just modified for stand alone use
What do you charge to do a stand alone harness for my 2007 Accord 3.0
Are you still making these harnesses? I need one for my 64 Baja...😀👍
Yes we are
@duneaddict I sent you a message on IG... I don’t think I've heard back yet...
Which plug is black/yellow come from b plug or c
hello good morning nice video
how can i get ahold of you to have my harness done
and does the ecu need to be flashed also?
thank you
Send me a pm on Instagram
@Dune_addict
Thanks for the video! I'm curious, if I am using an ECU from an auto trans, does anything additional need to be done to the ECU to allow the motor to function normally? Thanks!
nope
@duneaddict hey bro does anything have to be remove from ecu for it not to read auto transmission, pressure valves solenoids plz lmk
What transistors do I have to remove I really need help
What needs to be done to modify the PCM for standalone use?
Have you ever messed with a Honda C27? I acquired one in a trade for some buggy stuff and it already has a brand new Kennedy adapter setup so I was thinking about throwing it in my rail but I’m not sure what to do about the harness?
C series stuff is really outdated, youd need a aftermarket ECM and there not much support for that platform, Most people I know with the are swapping to J series
Well dang. Thanks for the feedback man. I appreciate it!
Awesome video!
Great content. 👍 looking at getting into dune buggy/ trail buggy..here in idaho. I have an 00 odyssey j35 as my donor. I will pull everything I need and send a pcm to you, I own a small mechanic shop and can do the wiring. Just not modify pcm. Thanks agian
ok got a question, I have a vw baja, looking for a new trans and power plant. should I got ls? or one of these j35 engines? it is set up for mid travel right now.
J35 will do it right..
Thank you for posting this video. I've been looking for videos like this and haven't found many. Can you please tell me if this would work for a j30 and a AEM standalone? I do have wiring experience but I've never done this before and want to make sure it will work before I purchase it. Thank you.
Yes sir it will thanks for watching
@duneaddict hey Bro quick question what hardness is that from a 03 Odessy or Acura cl?? Please let me know thanks
Question:where do you send the pcm to get the antitheft system removed?
Me
How much you charge?
@@josemadero7258 pm me
I did
Can any oem ecu be stand alone
No
@@duneaddict can a miata 1.8 be done
How can i get a hold of you to get info on the stand alone harness and computer
Pm me on Instagram
Dune_addict
Hey bro u help me with the auto transistors removal location @duneaddict
Can you make a video about the ECU for this stand alone harness?
I could but it's like giving out the recipe of the secret sauce...lol,
If you know your way around a honda ECU it's not that hard, also I don't wanna show how to remove the Immobilizer. Makes it easy to steal a car, if you need help with a specific project send me a PM
@@duneaddict thats fair. ;-) I am new to this honda J world and am trying to learn all I can. My application is similar to a sandrail but in a rock crawler.
not much j35 info more like how to wire a relay
How do you remove vsa and abs later acceleration sensor
Price?
Do you have an email I could contact you at for some questions?
Hndarcr@yahoo.com