You could weld a flar bar on the top of the top of the angle iron edge to stiffen it from flexing under load and also cut some flanges in it to make it possible to bend small tabs to build boxes
Great video. I think this is the best video so far I have seen on showing how to build a bender. I have some old structural 10mm angle iron so I will build a heavy duty bender using your method. Thanks for the upload.
Just a thought here but I noticed your bending bar (head) deflects drastically while you are bending especially in the center!! I was wondering though why you couldn't support it more like you did with the flat stock you welded to the feed bender!! Though you would have to cut the bar stock thinner to allow it to sit into the head and not interfere with what is being bent, BUT it would make the head stock more rigid and it would flex up as much while making bends in thicker material!! I have also seen where guys weld a pyramid shaped brace to the head to give it more tension on the center!! Not saying you design is bad, BUT I just noticed how much it flexes during operation is all, and there are ways to fix that with just a little more work is all!!
Greg Benwell nice comment. I want to build a sheet bender and thinking of using a thicker gauge angle iron. I have some really thick structural angle iron so will consider using it. This is the Better video so far in the way the video has been presented not times delay on the important bits as for painting that's not of importance to show at normal speed.
Buena idea solo un detalle el ángulo superior está muy atrás por eso la curva del dobles es algo abierta y prolongada este debe de ir justamente al ras de la base
По середине гнется зажимной уголок, доработаю конструкцию, этот же уголок заточи чтоб угол острый был и зазоры большие, короче смотри учись у русских чайник.
Si cambias las bisagras que usas por unas de piston o de cilindro (las que son para soldar) los acabados serán mucho mejor ya que este tipo de bisagra no flexa como las otras saludos
Veo que se arquea el ángulo central de la parte fija al doblar se levanta ese ángulo pero la idea está buena el que desee hacerlo mejor claro meterá en vez de ángulo una plancha de 1/2 y esos tornillos que le pusiste par subir y bajar se puede poner más grueso digamos 2 pulgadas cosas que sevea más robusta y doble sin problema son ideas que doy
Nice 👍🏻 Learned if i use Bright bar metal stock it give a more sharper fold ie no bull nose ! maybe i will make two heads for mine out of mild steel and the other from bright 👌🏻
I see a bunch of these brakes with good build but that edge is always poor. Angle iron has a hemisphere with the same diameter of the material on the edges. I used a piece of C channel placed open end up for the stock clamp. Edges are beautiful even with 14 gauge mild steel.
You could weld a flar bar on the top of the top of the angle iron edge to stiffen it from flexing under load and also cut some flanges in it to make it possible to bend small tabs to build boxes
Great video. I think this is the best video so far I have seen on showing how to build a bender. I have some old structural 10mm angle iron so I will build a heavy duty bender using your method. Thanks for the upload.
You had some Bo Jackson there in the middle, you better put your top brace on it. 😆
Nice video, simple and clearly displayed. A great example of how to do this. Thank you!
I came here for the guitar solo, and I ended up building a brake press.
Just a thought here but I noticed your bending bar (head) deflects drastically while you are bending especially in the center!! I was wondering though why you couldn't support it more like you did with the flat stock you welded to the feed bender!! Though you would have to cut the bar stock thinner to allow it to sit into the head and not interfere with what is being bent, BUT it would make the head stock more rigid and it would flex up as much while making bends in thicker material!! I have also seen where guys weld a pyramid shaped brace to the head to give it more tension on the center!! Not saying you design is bad, BUT I just noticed how much it flexes during operation is all, and there are ways to fix that with just a little more work is all!!
Greg Benwell nice comment. I want to build a sheet bender and thinking of using a thicker gauge angle iron. I have some really thick structural angle iron so will consider using it. This is the Better video so far in the way the video has been presented not times delay on the important bits as for painting that's not of importance to show at normal speed.
Well done! Really great job I really liked the work 🔥🔥🔥
Looks like you could put a top brace on it to hold the center down.
Plein de vidéos intéressantes, merci.
Can you use bed frame to make this?
Buena idea solo un detalle el ángulo superior está muy atrás por eso la curva del dobles es algo abierta y prolongada este debe de ir justamente al ras de la base
Well thought out neat design. Cheers, Rob.
По середине гнется зажимной уголок, доработаю конструкцию, этот же уголок заточи чтоб угол острый был и зазоры большие, короче смотри учись у русских чайник.
Si cambias las bisagras que usas por unas de piston o de cilindro (las que son para soldar) los acabados serán mucho mejor ya que este tipo de bisagra no flexa como las otras saludos
Hi bro! This metal bender can bend stanless steel 2mm?
Que bien .que podamos aprender cada dia mas
Veo que se arquea el ángulo central de la parte fija al doblar se levanta ese ángulo pero la idea está buena el que desee hacerlo mejor claro meterá en vez de ángulo una plancha de 1/2 y esos tornillos que le pusiste par subir y bajar se puede poner más grueso digamos 2 pulgadas cosas que sevea más robusta y doble sin problema son ideas que doy
Nice work.
I'm making one after watching your video
Nice bender.
nice video bro
Good job
Muy buena la dobladora.Exitos!.
Measures?
Same mistake as many , should have flatted edge of angle Iron and drilled through for hold Downs
Nice 👍🏻 Learned if i use Bright bar metal stock it give a more sharper fold ie no bull nose ! maybe i will make two heads for mine out of mild steel and the other from bright 👌🏻
That’s terrific thanks
Precio? En Argentina hay alguna de esta? Muchas gracias
Le faltó más fuerza en el estabilizador se levanta. Así ya no sale tan redondo el dobles. pero muy buen equipo.
alat bagus banget,,,tambah josss,jika arah temukan k bawah,jd tenaga lebih efisien, nd lebih mudah,,,, cuma sekedar masukan
Can this handle 5mm thickness?
A sheet metal brake would be very useful when I'm working with my everlast tig welder. Inevitably I need to bend something whenever I weld.
can bend 4mm plate?
1,5 mm thicknesses bending properly ??
Maximum sheet ??
What is cost ? Can u sell this item
यह मशीन हम कैसे प्राप्त कर सकते हैं
klo.bli.yg udah brapa from lombok
Salut tu pourrais nous donner les mesures
Four side bending? Like Rack shelf
Nice work but there's a lot of improvement to be done, especially the gap between edges for a sharp bend on its corner, and support on the center.
i agree, thats why he is not getting the shape bent
I see a bunch of these brakes with good build but that edge is always poor. Angle iron has a hemisphere with the same diameter of the material on the edges. I used a piece of C channel placed open end up for the stock clamp. Edges are beautiful even with 14 gauge mild steel.
@@alvaroramirez5086 Good suggestion. It eliminates the round over you always find on the angle edge.......thanks, going to change mine.
Gracias y saludos desde Mexico.
thanks
Why do you keep cutting the steel twice?
el punto de encuentro debe quedar en cero por eso el plegado queda redondo
Great video!
ভাই এই মেশিন কোথায় পাওয়া যাবে
Buat plat max brp mm om..??
Hermoso espléndido
Muito profissional.
Làm dài 2m dc k
Bonjour, moi je cherche une plieuse manuelle à tôles, pour les chambrales des portes. Je suis en Rdc Congo
4mm??
Hola muy buenas
осталось сточить,края зажимного.,тогда полукруга ,не будет..
Very good
I need to use my powerarc to make one of those.
Ok so it bends small pieces of steel now bend some the length of what you’ve made the folder
Thank you
Esaas dobradiça São frágil de mais como também as cantoneiras tem que ser 3/16 ou 1/4
Ficou mais ou menos poderia ter feito sistema pra aumentar ou diminuir o raio da dobra, dependendo da chapa se o raio for muito pequeno ela quebra.
Muito fraco
👍🏻
Mashin chahiye
Лайк 👍👍👍👋👋👋
Good
bisaan ey si akang nyiena. hade
plate 0,2 mm max
Oben angle
The idea is good, but the result is not very good! The bending radius is too large.
Lo maximo
Nice
Ok
Not a good design. If you bend a sheet you have to work more to get it out from the machine than to do in bending it.
That wasn’t a sharp bend, had quite a radius on it
Punten slurrr
i like
🙏🙏🙏🙏
Bend it like a banana, no sharp angles at all. I need something better, have to figure it out.
Simple solution, grind your edge sharp on the clamp angle.
good one but music sucks.
Cerniere deboli!!
Punten slur
Kitne me milegi mashin ret 8504936199
плохо
Pelqej
That’s terrific thanks