NEW Creality Ender 3 Max Neo - Is it the One?
Вставка
- Опубліковано 25 сер 2024
- #3DPrinting #Creality #Pergear
This is the new @Creality3D #Ender3 Max Neo. Has a lot of standard features. 32bit Silent Board, Dual Z Steppers, 300*300*320 build area. 4.3 Inch color control knob display, filament runout detection, power loss recovery, and CR Touch leveling. However, how will this new printer perform?
【CR Touch Automatic Leveling】:Equipped with CR Touch, the 16-point automatic leveling can complete quickly with compensation for points' printing height on the heat bed. Good efficiency saves much time.
【High-precision Dual Z-axis】:With a Z-axis dual-screw+Z-axis dual-motor design, Ender-3 S1 works smoother and more synchronously to lower the possibility of lines and ridges on the sides of your print, thus improving the printing quality.
【Upgrade Red Metal Extruder & Low-noise Design】:The new upgraded extruder without pneumatic joint has high gear density, feed-in smoothly, greatly improving the performance of printer; and the brand-new 32-bit silent mainboard runs at low decibel levels, greatly reducing noise to let you enjoy your printing.
【300 x 300 x 320mm Large Build Volume】:With the 300 x 300 x 320mm Large Build Volume and an open print chamber, you'll be able to print large 3D models with ease, or you can print several small models at the same time on the large build surface.
【Power Loss Recovery and Filament Sensor】:Ender-3 Max Neo features the function of detecting filament runout or breakage/power loss and resume printing after recovery. By accurately recording the printing data at the time of power outage/filament runout or breakage, it helps to avoid the waste of filaments and time caused by accidents.
Purchase
Amazon US:
amzn.to/3JAJdPF
amzn.to/3QiHMao
Pergear PEI Steel Plate:
amzn.to/3Q6rZvV
Amazon CA: www.amazon.ca/...
Amazon UK: www.amazon.co....
Creality CR-PLA Matte:
amzn.to/3P47e2r
Pergear:
www.pergear.co...
Ferrule Crimping Tool Kit - Sopoby Ferrule Crimper Plier (AWG 28-7) with 1800pcs Wire Ferrules Kit Wire Ends Terminals -
amzn.to/3zdPuvL
Clockspring3D models -
clockspring3d....
Disclaimer - This is an instructional video only - I assume no responsibility if you do not become a pro after watching this video. This video is for learning purposes only, you are following the steps in this video at your own risk!
/ tripodsgarage
/ tripodsgarage
/ tripodsgarage
Thanks for watching - Please Like and Subscribe!
Tags
CR6-SE, CR6SE, 32-Bit Control Board, TMC2209 Stepper Motor Driver, 3D Printer, 3D Printing, CR-10, CR-10s, Ender 3, Ender 3Pro, Ender 5 Pro, Ender 5, creality silent board, silent board, BIRGTREETECH, SKR CR6V1.0, #Artillery Hornet, Artillery Genius, #Kywoo Tycoon Slim, #Ender5Plus #CR6SE, #FLSUN #SR #Superracer, Bondtech #FOKOOS #ODIN-5-f3 #3DPrinter #3DPrinting #longerlk5pro #longer3dprinter #LK5PRO 3D Printer Ender 3 Max, Creality Ender 3 Max Neo
Thanks for the video! Mine arrives tomorrow and I'm excited about it and I'll be sure to check on the tensions of everything especially the issue you found.
John, Excellent review as usual. Good catch on the loose extruder tension. A bid help would be an Ender 3 family tree, going back to the original. There must be 20 -30 Ender 3 versions, a list with comments would be helpful.
Yeah, I started to over think what the issue could be. Luckily it was a very simple fix. These printer manufacturers always post videos, assemble, load filament, then print! I thought about talking about the Ender 3 forest of printers. I figured someone else can go down the rabbit hole with their review 😂😂
Thanks for the review, now I know some more things to look for. Seems I made a good purchase!
the only riable video, nice work
If you throw the glass bed in the freezer for 5 minutes it will usually release the print. I did a very large 210x200mm print on my Ender 3 Neo and it popped right off.
Second this. Don't even need the freezer the fridge works too. I only know because I don't have room in my freezer for anything of much size. LOL.
Excellent video
Great review! Yes if creality would make a few small addition changes, then they could have the perfect printer.
What additions changes do you recommend
@@Shamsher1 I'd install a flex sheet instead of glass. Probably Ultistik. Capricorn tubing for the hotend liner. Dual duct part cooling fan/s. Dual drive gear extruder. I appreciate they are using a metal extruder kit, but its single gear.
Great review. It's always the lack of attention to detail where Creality falls short.
Yep! Seems to be a growing pattern amongst these manufacturers
great review
Thanks bud!
Thanks man!
Has to be something with your settings, setup, or filament, I've seen several videos on this printer and all the prints turned out beautiful except maybe a lil ghosting but nothing bad. On the video that the prints looked beautiful before the first print he adjusted all the rollers, belts and then leveled the bed. He also changed several setting in the software "Cura" that he was using. The changes he made definitely worked for the better.
great top review . I wanted to buy this model and your video helped me a lot. thank you
Love the video! Yeah, it is amazing how the instructions only shows how to build and possibly print something off the SD card. When I comes to tightening the extruder, there is nothing in the instructions.
Yeah, it would be nice if they had a small troubleshooting guide at the end of the manual. If your print looks like this, try this!
Yeah, not happy with my extruder. What would be a good upgrade?
Another Top video 🤟🤟🤟🤟🤟🤟🤟
Why did you take the standard ender 3 cura profile instead of the ender 3 max cura profile
What settings do you use for the retraction?
my original max has the same banding in the benchy I thought if I put in my max a dual Z it will fix it but with this video I realized is another problem
Thanks for the great review. Complete newbie here, when you use the PEI plate,do you need to recalibrate the printer?
Oh great another ender 3 clone... oh wait! good feedback on this one buddy! PID tune ?
The never ending Ender 3 forest of 3D Printers!
i have this printer 😊🎉
Looking to get either the ender 3 S1 pro or plus or the Max Neo would you recommend is the best machine
What did you pick?
TPU or no
I followed all the steps and the auto leveling just doesn't seem to want to work
I was having problems with prints sticking to the bed. I no longer touch the bed with my hands. Problem solve.
If I recall this video correctly, the prints stuck to well.
@@TripodsGarage OK, let me redo my post: Unlike the person in the video where his prints are sticking to well, l'm having problems with prints sticking to the bed. I no longer touch the bed with my hands. Problem solve.
@@DueyMiller-rk9dr - Typically you don’t touch the bed with you hands so no oils get on the bed surface. So you still don’t touch the bed with your hands, so the prints stick. Got it!
@@TripodsGarage I was touching the bed because if you run your fingers lightly over the first outside bead laid down and it moves your should stop printing. I thought like a moron that was a good way to check for print failure. Which it is but you have a ton of oil all over the bed.
@@DueyMiller-rk9dr I use electronic wipes on the bed after print to make sure it is clean. Just a sugestions..
One tip I have for getting prints off of the creality glass is to take the entire glass plate off the bed and put it in a freezer for 5 minutes. This causes the glass to shrink slightly. The prints usually come off without a problem.
I have noticed inconsistencies in the glass. I have 2 Ender 3 v2s. One of them sticks really well and the other has bed adhesion issues. I wonder if they use different recipes for the carborundum glass or something.
Yeah, I have used the freezer, and under cold method over the years. However, this print finished at 11pm, and the print wasn’t removed until 9am. With my other glass beds these prints would have fallen off. I am with you, there are inconsistencies with the production of the glass. I cleaned the glass thoroughly, and it still feels sticky.
Wait... Dual Z *WITH* a belt? How does that work exactly. 🤔🤔🤔
Good to see yellow springs at least & looks like the same strain relief as my 3yr old version from them.
Why do companies still use glass when flex options are so much better/easier. 🤦🏼
I run 10x10 mesh on my (formerly) Ender 3 Pro.
I used really like glass beds until I discovered flex plates. This glass was absolutely ridiculous! There was no glue stick or anything used, was completely cold. A 3x3 grid seems pretty out dated.
May I ask what’s the printer’s dimensions while in operation (Bed Front and Back extended?
My Max Neo is coming in from Creality and I’m going to build an enclosure before it arrives.
Do you still have the max neo? If so how do you like it? I'm considering getting one.
@@OganySupreme According to my neighbor, the delivery guy tossed my package like a rag doll. I took pictures of the damages, sent it back to Amazon and I didn’t reorder. I’m saving up for the Prusa MkIV.
@@joiscara7191 Geez that's horrible.
Looking to buy either the Ender 3 Max or Neo, which do you recommend? Is the Neo quieter?
Unfortunately I do not have the Ender 3 Max to compare it against. The E3MN is very quiet at 60db as mentioned in the video.
ender 3 max and upgrade,if you get a neo you will regret it believe me.
@@roddsmith8954 What made you regret the max neo?
So if I understand correctly under extrusion was corrected by lowering nozzle ?
By tightening the extruder, more pressure on the filament feed
@@TripodsGarage oh it was loose
Umm 3d printing 101, you ALWAYS check the tensions all around when assembling a machine. How did you even miss that??
Does it say to check it in the manual?
@@TripodsGarage It doesn't have to, there are manufacturing tolerance, assembly tolerances, hell you picking up the printer from the box can cause things to come loss. Proper assembly always includes checking everything, and that 100% includes making sure everything is squared, all screws are tightened, checking belt tensions, the eccentric nuts on the wheels..etc. Did you check any of those? It seems kinda stupid to say the review would have been better if it wasn't for one screw being loss when you properly check these things out.
@@janosmegyeri1473 - Oh! So I am to do things that are not listed in the manual? Got it! Why? Because because this is 3D Printing 101! Is there a 3D Printing 101 course? Is that course included with every 3D printer that is purchased for all the new people? If it says to check the eccentric nuts, then they are checked, if it says to level the bed with the leveling knobs, then that is done. If it doesn’t say to check extruder tension, then it doesn’t happen. You know why? Because “it isn’t in the manual!”. This is exactly what is wrong with these responses. People with experience belittle others that do not. You do all this things listed because you have experience with 3D printers. Yet, you cannot go back down to the level of somebody that doesn’t know one little thing about them. Am I going to unpack a inkjet printer and checks the belts for tension if it isn’t in the manual?
Maybe manufacturers should have a tuning guide? Or a checklist like with what you are saying? Now that would be a step in the right direction for newbs! Pleasure trolling with you, have a frosty beverage and have a relaxing rest of your Friday!
@@TripodsGarage Wow dude, chill out. My initial comment was sincere, I was surprised it didn't get caught during setup, but then you have to come back with a snarky remark like does it say to check it in the manual so ya, I;m gonna call you out on it. You say "People with experience belittling other that do not" but you are a content creator with nearly 20k subscribers, and over 100 vidoes, you have experience man.
That is exactly why I called you on it bro, because you aren't the person "back down to the level of somebody that doesn't know..". If you were new, I would have taken that as a teaching moment to provide some tips when assembling a 3D printer, but you clearly are not new.
-peace
@@janosmegyeri1473 No, this was a belittling comment. You claim this is "3D Printing 101" to check all the nuts bolts, tensions. Again, where is this 3D Printing 101? You 3D Printing 101 comes from experience and nothing more. All these manufactures are now claiming 15min or less setup times. Then you are off and printing. It says absolutely nowhere in the manual to adjust the extruder tensioner, or why would you even need to. All that is needed is to have a checklist with what to check, and explaining what does what. I could have easily just let the failures be, and post the video as is. You are right, I have 20k subs and experience, and try to hold myself to higher standards with my content. I show most of the assembly process, explain parts, go through settings, results, pros and cons. I just don't have an assembled printer sitting next to me, and showing off printing parts then call it a day. I decided to see what the issue might be, and recorded my findings. I will correct you, this was a teaching moment.
People need to start holding these manufactures to a higher standard of documentation and accountability, and not let the community pass the buck for them. There is a reason why all these manufactures ask people to join their Facebook Groups, so the community can be their free tech support. I see it all the time, someone posts a part that breaks, people say "by a replacement, or a new upgraded part, it will take too long for them to send you a replacement". Instead of having them go through the manufacture, and get a replacement under warranty. I never see this behavior on Facebook Groups for people that buy new vehicles. Why should this be any different?
Now with all that being said. I will actually take your comment under advisement. And will be more aware to my targeted audience. The only thing I ask from you, is to hold other content creators and manufactures to that standard as well. I put a lot of effort into my content, and try "not to do" what everyone else does with my content and show more. Now, I cannot remember everything, and I am trying to shorten my videos to under 13min.
Enjoy your weekend!
bad layer line alignment
No touch screen. (Makes fart sound) 👎🏻 blllllllpppppppppt. 💩