Thank U om...akhirnya ketemu juga solusinya....because saia sudah habiskan 8 pcs esc emax blheli 30a dan 4pcs emax blheli 12a semuanya burn ketika proses setting di openpilot or libre. ternyata pada kabel esc positif di potong dan arus 5v d ambil dr PDB....terima kasih banyak om....salam dari Indonesia
Thanks, Robojax. Good clear explanation of how to wire up the CC3D with associated components to build a quad. Very helpful for an amateur like me. Great job.
Hi, one question, what can I use in place of the ccd3d equipment as none of it is available in the present, 2024, please take out the part in this video that states you sell it. Now, I am building a quad drone that was originally based on a Nano board, but this did not work out. I now need a Flight controller that I can connect to my 4 individual ESC's, can you suggest any? Thank you.
Very nice video. I understand the ESC connections and 5v but my FrSKy little receiver doesn't have 6 channel inputs. It does have more features but less connections. Do you have any suggestions on how to understand how to use it?
I really need to know because I didn't understand well, if I have PDB with the hole, the "blue sky panel", I need a 5V regulator between the pdb and the flight controller? It's my very first time doing this kind of things and I have only seen university laboratories with easy circuit to mount 😵 I really like your videos!!
Good video... Question though - When powering the FC with a PDB the FC does not need the ground wire? I noticed you only connected the positive wire from the PDB to the FC, but no ground wire?
Just watch at 7:10 . Flight control need 5V. Either provide the 5V from PDB or ONE (only ONE) of the ESC. The ground: when you connect the ESC, it will be the ground. All grounds are shared. So don't worry.
Glad it was helpful! The best thank you for me is to not skipping ads and Subscribing 🔔 to my channel, and clinking 👍 the video. It is greatly appreciated. 🔔 😊. I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊 .
Hi Robojax. ? That was a beautiful video. very informative. keep up the good work. Can you also make a video on connections for dasmikro 2.4ghz kyosho receiver and binding it to a flysky fs-t6 transmitter..thanks in advance bud.
If i’m using the esc with no 5v. I have to get the 5v from the pdb and connect the white and black wires of the esc to the cc3d channels. I have a pdb xt-60 is there any problem? And why you don’t sold a positive and a negative wire from the pdb to the cc3d you only connected one if i have the no 5v esc i have to connect a positive and a negative? Thankss
I have explained this. But here again. CC3D need power. Either from pdb or from ESC. but ONLY one. not both. So if your ESC don't have the 5V, then provide 5V from pdb.
Robojax and if i want to connect a fs-ia6 receiver i plug the wires of multilple colours that come with the cc3d to the cannels of the receiver . That will work?
at 06:50 (click on 06:50 to watch) I have explained that you will get 5V from ESC. If your ESC doesn't have 5V, get it from PDB (watch at 08:55) and I have shown at 12:55 when 5V from PDB is connected. for the multiple coloured wire, see it at 14:20. I had to down and watch the video to get those times for you. Hope this resolves you issue. Please watch the video again. I have left no question un-answered.
hello, your video is well understood. sincerely with this i can go on to build my custom flight. in the video time (21:27/24:08), there you used a cable to bridge the last channel BIND BAT in one of the receivers. please can through more light on what happened there? thanks so much.
excuse me, if you ie use aileron stick for a second and then release it, what would happen? the plane goes back to level or u need to turn fc on or off for maneuvers
Hello,,,I followed exactly asper your video,but when I get to Libre Pilot setting,on the transmitter setup, center all your sticks then click next,,,,where you suppose to move both sticks around,,,,this is the point where I cannot move both sticks...can youhelp tq
I'm talking about these kind of inverters : www.banggood.com/NAZE32-Flight-Controller-SBUS-Signal-Inverter-for-RC-Multicopters-p-1034503.html I was wondering because nobody reported my reciever working with the CC3D and SBUS.
Hey having trouble seeing any stick movements with a FS A8s receiver and FS i6 transmitter in Betaflight. I've set it to IBUS and bound up no prob. Scratching my head as to why no stick input ... any ideas most welcome. Thanks! Paul
Hey, it could be anything as to why motors are not responding. Your ESCs could be NOT armed. Find out what ESCs you have or your flight controller isnot allowed the motors to be armed.
you can do it. But it will look very ugly and you won't be able to resolve an issue. It would be very hard find the problem for example with a morotor or ECS, then you need to unsolder may bell all wires to remove just one ECS.
RoboJax Videos quick question sir. iam a beginner to quads. Iam trying to build my first 250size racing quad and i dont know what flight controller to use. I do have a cc3d just sitting hear should i use it ? Any help would be great
we have the same receiver which used at the last , power supply to the receiver is given through usb port by laptop connection but we didn't see any blinking in the receiver?? any help from your side....
Check the voltage going to receiver using a multimeter. (multemeter (-) to GRD and (+) to the middle wire) if you don't see 5V then the voltage has issue or board is bad. If you see the voltage, make sure both (-) and (+) to receiver is connected. if you still don't see light, then receiver might have been burned/dead. Replace it.
that is to provide 5 volts to flight controller (FC). so if you have 5v supplied to FC, then you don't. So if your ESC has the 3 wire servo cable, that is UBEC and it means the ESC has 5v.
Hello,please help. We have cc3d cobtrioler. But we cannot make true connection with computer and cannot true update/ upgrade. İf you can help how ican send photo for helping
I have build the drone and it doesn’t work could you please help me? I have the esc with no bec and i connected them to the 4 channels of the cc3d , then i took 5v from the pdb ( i welded a red cable from the 5v of the pdb) and conected to chanel 5 on the positive . The cc3d has no power. What am i doing bad?
I am not able to upgrade firmware in libre pilot it's showig "Timed out while waiting for a board to be fully connected! You will have to manually upgrade the board using the uploader plugin." Also Rx & Tx is not showing please help me sir 🙏🙏
each ESCs will generate 5V. But the 5V will be like 5.123V and 5.052. So the difference 0.123-0.052=0.086VG or 86mV will be dissipated in the flight controller. This is happens with all 4 ESC. So yes cut them to be safe.
Robojax Thanks, While doing research I found an alternate answer. The ESC bec are of two types. Switched and linear. While linear it is OK to connect all the bec but switched bec will have problem because of how it actually produce 5v, by switching at high frequency. They may go out of sync when all four connected together.
Receiver needs 5V. You can't connect it to 3S. I don't know how you connected it but it should have been connected via ESC or another way from the regulator or PDB. Y
I was selling these items and buyers used ask questions and I know to leave nothing without answer. Watch it again with attention and I am sure confusion will be removed. I have left nothing out within the scope of this tutorial.
is it also possible to use fs-ia6b with ibus on cc3d?
Same setup I think
We need a fsia6 I bus thorough video for cc3d
Fs ia6b sorry
Robojax way great videos can you do a video on fsia6b IBUS on cc3d
@@JB-po2mv sorry i moved to frsky. Besides cc3d is so old and not good to use these days. Use atleast f4
Watched many Vids on this subject, only after watching this I understood correctly what I need to do. TYVM. Will be watching more of your Vids :)
Thank you. I am pleased you found it useful.👍
Thank U om...akhirnya ketemu juga solusinya....because saia sudah habiskan 8 pcs esc emax blheli 30a dan 4pcs emax blheli 12a semuanya burn ketika proses setting di openpilot or libre. ternyata pada kabel esc positif di potong dan arus 5v d ambil dr PDB....terima kasih banyak om....salam dari Indonesia
Sama sama. saya senang bahwa video saya membantu Anda. Allahku melindungimu dan keluargamu.
Thanks, Robojax. Good clear explanation of how to wire up the CC3D with associated components to build a quad. Very helpful for an amateur like me. Great job.
You are welcome. I am glad you found it helpful.
awsome job, got my fpv working thnx to you
you are welcome. I hope you've subscribed as your subscription help my channel grow. Thanks
well explained. I have an old board im gonna use. Thank you.
Hi, one question, what can I use in place of the ccd3d equipment as none of it is available in the present, 2024, please take out the part in this video that states you sell it. Now, I am building a quad drone that was originally based on a Nano board, but this did not work out. I now need a Flight controller that I can connect to my 4 individual ESC's, can you suggest any? Thank you.
Very very well explained. Very educational. 2 thumbs up. Thank you so much.
You are welcome.
Thanks for your excellent video sir, was very useful!
You are welcome.
Thank u Robojax wao I was looking for this video .
You are welcome. I am glad you found it useful.
Very nice video. I understand the ESC connections and 5v but my FrSKy little receiver doesn't have 6 channel inputs. It does have more features but less connections. Do you have any suggestions on how to understand how to use it?
Thanks for explanation احسنت 🇰🇼
Can I use a GPS with this flight controller
If yes which one I can use
yes you can use. just search for "cc3d gps" on eBay or AliExpress. I have not used it but you can I am sure.
I really need to know because I didn't understand well, if I have PDB with the hole, the "blue sky panel", I need a 5V regulator between the pdb and the flight controller? It's my very first time doing this kind of things and I have only seen university laboratories with easy circuit to mount 😵 I really like your videos!!
I am glad you found it useful.
Good video... Question though - When powering the FC with a PDB the FC does not need the ground wire? I noticed you only connected the positive wire from the PDB to the FC, but no ground wire?
Just watch at 7:10 . Flight control need 5V. Either provide the 5V from PDB or ONE (only ONE) of the ESC. The ground: when you connect the ESC, it will be the ground. All grounds are shared. So don't worry.
I think the emax 12A Bheli is a linear ESC ? You don't need to cut the red wires or add an extra 5V. If they are switched or else then you do.
If you don't cut it, the current will flow between devices if the voltage is not exactly 5V. so it is a good practice to prevent that.
Hi I dont seam to be getting power to my rx from the cc3d I have done what you did in video but don't seam to be working
Excellent explanation. Thank you. 😀
You are welcome.
this video was helpful... thank you
Glad it was helpful! The best thank you for me is to not skipping ads and Subscribing 🔔 to my channel, and clinking 👍 the video. It is greatly appreciated. 🔔 😊.
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊 .
u should have used a cutted positive pin to (5v) power the cc3d ,,,just to avoid mistake and short out the board...min 13.30
Hi Robojax. ? That was a beautiful video. very informative. keep up the good work. Can you also make a video on connections for dasmikro 2.4ghz kyosho receiver and binding it to a flysky fs-t6 transmitter..thanks in advance bud.
Hi Srikanth, I am glad you liked it. I till see if I can get the component and will do a video on that.
Excellent description, thanks
You are welcome.
Excuse me on omnibus f4 pro v3 which one is the correct port? And doest it have it?
this video is about CC3D. sorry.
If i’m using the esc with no 5v. I have to get the 5v from the pdb and connect the white and black wires of the esc to the cc3d channels. I have a pdb xt-60 is there any problem? And why you don’t sold a positive and a negative wire from the pdb to the cc3d you only connected one if i have the no 5v esc i have to connect a positive and a negative? Thankss
I have explained this. But here again. CC3D need power. Either from pdb or from ESC. but ONLY one. not both. So if your ESC don't have the 5V, then provide 5V from pdb.
Robojax thanks but you only connected a + cable to the cc3d from the 5v pdb . I have to connect + and - ? Or only +
Robojax and if i want to connect a fs-ia6 receiver i plug the wires of multilple colours that come with the cc3d to the cannels of the receiver . That will work?
at 06:50 (click on 06:50 to watch) I have explained that you will get 5V from ESC. If your ESC doesn't have 5V, get it from PDB (watch at 08:55) and I have shown at 12:55 when 5V from PDB is connected.
for the multiple coloured wire, see it at 14:20. I had to down and watch the video to get those times for you. Hope this resolves you issue. Please watch the video again. I have left no question un-answered.
Robojax thanks a lot i am a beginner and i’m a llitle bit lost.
Can you connect esc to battery directly without the flight controller and bec?
Yes you can. 4 ECSs with 8 wires will be very messy.
you explained it really good! thanks
You are welcome. Good to hear that.
hello, your video is well understood. sincerely with this i can go on to build my custom flight. in the video time (21:27/24:08), there you used a cable to bridge the last channel BIND BAT in one of the receivers. please can through more light on what happened there? thanks so much.
the bind cable is uses only when you bind the transmitter with receiver. here I used to to show the blinking of the LED nothing more.
excuse me, if you ie use aileron stick for a second and then release it, what would happen? the plane goes back to level or u need to turn fc on or off for maneuvers
yes it goes back to level.
Hello,,,I followed exactly asper your video,but when I get to Libre Pilot setting,on the transmitter setup, center all your sticks then click next,,,,where you suppose to move both sticks around,,,,this is the point where I cannot move both sticks...can youhelp tq
So the two kinds of bec boards are interchangeable？
Yes. depends on the features and how you use them.
I'd like to use SBus on my quad since my reciever can do it. But do you need an "inverter" like for the Naze32 ?
I don't which inverter you are talking about. for CC3D you don't need anything extra. Bus can be connected to the flight controller.
I'm talking about these kind of inverters : www.banggood.com/NAZE32-Flight-Controller-SBUS-Signal-Inverter-for-RC-Multicopters-p-1034503.html
I was wondering because nobody reported my reciever working with the CC3D and SBUS.
No you don't need it if your receiver has SBUS output. this is for the receivers with multiple servo output to make is ONE output for SBUS.
RoboJax Videos thanks ^^ will plug it and test it this evening.
Hey having trouble seeing any stick movements with a
FS A8s receiver and FS i6 transmitter in Betaflight. I've set it to IBUS and bound up no prob. Scratching my head as to why no stick input ... any ideas most welcome. Thanks! Paul
Hey, it could be anything as to why motors are not responding. Your ESCs could be NOT armed. Find out what ESCs you have or your flight controller isnot allowed the motors to be armed.
Robojax Thanks 👍
Kindly make a video for transmitter.
this video is in a very low demand. Very costly to make a video specially I am in Canada and any drone you fly needs license.
Can we add telemetry in cc3d flight controller
is it necessary to connect power distribution or we can join in parallel all together to battery..
you can do it. But it will look very ugly and you won't be able to resolve an issue. It would be very hard find the problem for example with a morotor or ECS, then you need to unsolder may bell all wires to remove just one ECS.
Robojax can we connect brushless dc motor to receiver without in cc3 d
Well explained.
Thank you.
realy nice guy help me so much thx
I am glad to be helpful. Thanks.
Are flight controller and power distribution the same thing? If they are is there a reason for using 2?
No they are not. they work together. Watch this video fully and you will understand it.
Excellent video thanks
You are welcome.
Great
will it be okay if i don't connect 5v from the pdb and leave one esc with a red wire so it gives the flight controller a 5v ?? pls someone answer!
Yes . It will work
@@robojax thank you so much
Can i ask , do I need a flight controller to accompany my Frsky 1a6b?
if you want to turn ON or OFF something else, you don't need flight controller. But if you want to fly a plane or drone, yes you will need it.
great work brother👍👍
Thank you.
RoboJax Videos quick question sir. iam a beginner to quads. Iam trying to build my first 250size racing quad and i dont know what flight controller to use. I do have a cc3d just sitting hear should i use it ? Any help would be great
we have the same receiver which used at the last , power supply to the receiver is given through usb port by laptop connection but we didn't see any blinking in the receiver?? any help from your side....
Check the voltage going to receiver using a multimeter. (multemeter (-) to GRD and (+) to the middle wire) if you don't see 5V then the voltage has issue or board is bad. If you see the voltage, make sure both (-) and (+) to receiver is connected. if you still don't see light, then receiver might have been burned/dead. Replace it.
Did i have to use an UBEC for my flightcontroler when my BEC has UBEC ??? Fast answer please :)
that is to provide 5 volts to flight controller (FC). so if you have 5v supplied to FC, then you don't. So if your ESC has the 3 wire servo cable, that is UBEC and it means the ESC has 5v.
Thank you for this video!!
You are welcome. The best thank you for me is to Subscribe 🔔 to my channel and like 👍 the video. It is greatly appreciated. 🔔 😊.
Helped me heaps thankyou
You are welcome.
I have sp f3 acro v1 is it the same wiring?
I am not sure.
Hello,please help. We have cc3d cobtrioler. But we cannot make true connection with computer and cannot true update/ upgrade. İf you can help how ican send photo for helping
Hello, I have a video on CC3D issue ua-cam.com/video/_cJx1NodY8c/v-deo.html
I have build the drone and it doesn’t work could you please help me? I have the esc with no bec and i connected them to the 4 channels of the cc3d , then i took 5v from the pdb ( i welded a red cable from the 5v of the pdb) and conected to chanel 5 on the positive . The cc3d has no power. What am i doing bad?
have you connected negative from battery to ESC and from ESC to the CC3d flight controller?
Thanks a million for that 👍
You are welcome. I am glad you liked it.
Which one si the port VBAT in the cc3d?
I don't have it in hand but perhaps you skippef the video. That is the most important part. Please watch it without skipping, you will get it.
good explation plus my friend
Thank you for your subscription and sharing this video.
Excellent
Thank you.
I am not able to upgrade firmware in libre pilot it's showig
"Timed out while waiting for a board to be fully connected! You will have to manually upgrade the board using the uploader plugin."
Also Rx & Tx is not showing please help me sir 🙏🙏
so on the other power distribution board where do i get 5v to power my flight controller
I believe I have explained it. Please watch the video fully without escaping.
Great video
Thank you. 👍
I need some help plz
I want to connect an arduino to cc3d to send send pwm signal
(Drone providing obstacles )
CC3D is already doing it. Why would you do that? Then use ArduiPilo which is for Air Plane or drone based on Arduino.
@@robojax could u give me some thing for contacting u email or facebook plz ??
Is cutting the 5v of all ESC but one necessary. Does it create problem if not cut. I mean over current to controller ??
each ESCs will generate 5V. But the 5V will be like 5.123V and 5.052. So the difference 0.123-0.052=0.086VG or 86mV will be dissipated in the flight controller. This is happens with all 4 ESC. So yes cut them to be safe.
Robojax Thanks, While doing research I found an alternate answer. The ESC bec are of two types. Switched and linear. While linear it is OK to connect all the bec but switched bec will have problem because of how it actually produce 5v, by switching at high frequency. They may go out of sync when all four connected together.
good man.
You are kind to say that. Thanks
thank you sir
Most welcome
What is the name of wire which you connect to receiver to flight controller
it is called flight controller cable for cc3d.
how to upload openpiolet in cc3d i am getting trouble
Here we have another video for that ua-cam.com/video/_cJx1NodY8c/v-deo.html
Why my receiver burned, i was followed that method, i use cc3d and battery 3s?
Receiver needs 5V. You can't connect it to 3S. I don't know how you connected it but it should have been connected via ESC or another way from the regulator or PDB. Y
Thanks for solution,,,my pdb may not give 5v but 11v so my receiver always burn,,, and i will place other pdb with output 5v, thank you very much
perfect
dear i have FS-R9B i need to run it with PPM What is the solution
this receiver will work without any change in setting with FlySky transmitter. Why do you need to set anything? Just bind it and it will work.
you are awesome
Thank you. So you are.
How to connect flight controller to its software. Please explain
If you search my channel with word "cc3d" you would find it . here I searched it for you ua-cam.com/video/_cJx1NodY8c/v-deo.html
Can u make a kk board connection to receiver
you can connect your receiver on the right side (3 pin connectors) see this photo usaquadcopters.com/images/612341231.png
Thanks
you are welcome.
Your video is really nice but Ur English is not so clear
Thank you. I have Canadian accent but that is not important. The important part is understanding the talk which I am sure you did understand.
how to connect cc3d evo with fs-a8s ?
Try this: image.helipal.com/le-0314-big001.jpg
RoboJax Videos Too much thanks!!
you are welcome.
is that ppm?
thanks
Yes sir... ppm and i-bus/s.bus
Trying to connect. Ia6c to rise vision?
To connect S-bus see this image: intofpv.com/attachment.php?aid=143
but you didnt tell how to connect all motor to chanel 3 to throtel
when I mentioned how to connect ESC, that is enough. You will connect motor to ESC.
Robojax
thankss for replyyy
My fly sky receiver still won’t work
what do you mean by "wont' work"? is it not binding or you don't see response from flight controller?
cant get the channels to corospond with inputs, need an encoder for wire for every channel receivers
This page had some good pictures too that might help www.multi-rotor.co.uk/index.php?topic=14131.0
Why do you use PWM, while you have an I-bus and an S-bus available ?
It's like taking your bicycle while there's a Porsche in the garage....
Not all receivers have s-bus, not all flight controllers have the input. So this was general guide.
Confusing...
I was selling these items and buyers used ask questions and I know to leave nothing without answer. Watch it again with attention and I am sure confusion will be removed. I have left nothing out within the scope of this tutorial.
Tgy