Danke für das Video, ich habe auch keinen Türkontaktschalter gefunden, aber nachdem die LED nur trübe rumfunzelte vermutete ich, dass die LED kaputt war. Ärgerliche Schwachstelle, der Kühlschrank ist auch maximal drei Jahre alt, die eine LED auf der Platine inkl. Versand knapp 18 Euro. Dämlich auch weil man die Platine nach dem Ausbau ganz einfach wieder in die alte Fassung einklicken könnte. Wird aber eine neue mitgeliefert. Ich habe Kunstoffwerkzeug für Arbeiten an den Verkleidungen in Autos verwandt. Das ging prima. Dank diesem Video war der Puls deutlich niedriger beim Ausbau, da ich mir ziemlich sicher war, dass das zerstörungsfrei möglich ist. Der Einbau ging auch prima.
Thank you Frank for your video i would like to add my experience too. The strange thing is on the board it says 3V, also spare part sellers said that its a 3V board but when i measured the fridge output its a 12V. Also i found a video on youtube a guy measure it 12V too and swap board with original one and it works. I don't understand how it works because in my knowledge there is no 3030 smd led which is working with 12V. I end it up with 3528 cool white led (forward voltage is 9V which is using on led bulbs actually) and 68ohm smd resistor(1210 imperial which can carry 0.5w) on the negative side. I cut the path closer to the male pins which enters to the fridge and solder the resistor. Its working as original one 🤓Service offered 40$ to change it which is very expensive for a single 3030 smd led.
Danke für das Video. Lichtproblem nach 2,5 Jahren an einem 1000€ Siemens-Kühlschrank. Leider hat die neue Diode keine Besserung gebracht. Alte wie neue LED leuchten nur ganz minimal in der Mitte. Hat jemand eine Idee, was wir noch überprüfen können? Ich sehe nicht ein, jetzt noch zusätzlich soviel Geld für den Kundendienst zu bezahlen. :-(
Hi, hab mal ne frage wie schauts aus hab ein siemens gerät sieht fast genauso aus wenn ich es bestelle könnte ich es als Laie problemlos auch machen natürlich vorher die Stromversorgung trennen natürlich
Neither at the door nor the housing i can find a mechanical switch. Guess that there is somewere a magnetic reed contact. Tried to check this by use of a magnet, but without success. Sorry and good luck for the repair.
Danke für das Video, ich habe auch keinen Türkontaktschalter gefunden, aber nachdem die LED nur trübe rumfunzelte vermutete ich, dass die LED kaputt war. Ärgerliche Schwachstelle, der Kühlschrank ist auch maximal drei Jahre alt, die eine LED auf der Platine inkl. Versand knapp 18 Euro. Dämlich auch weil man die Platine nach dem Ausbau ganz einfach wieder in die alte Fassung einklicken könnte. Wird aber eine neue mitgeliefert. Ich habe Kunstoffwerkzeug für Arbeiten an den Verkleidungen in Autos verwandt. Das ging prima. Dank diesem Video war der Puls deutlich niedriger beim Ausbau, da ich mir ziemlich sicher war, dass das zerstörungsfrei möglich ist. Der Einbau ging auch prima.
Freut mich, dass das Video geholfen hat.
Thank you very much, it helped a lot for 3 days I suffered with this lampshade!
Thank you Frank for your video i would like to add my experience too. The strange thing is on the board it says 3V, also spare part sellers said that its a 3V board but when i measured the fridge output its a 12V. Also i found a video on youtube a guy measure it 12V too and swap board with original one and it works. I don't understand how it works because in my knowledge there is no 3030 smd led which is working with 12V.
I end it up with 3528 cool white led (forward voltage is 9V which is using on led bulbs actually) and 68ohm smd resistor(1210 imperial which can carry 0.5w) on the negative side. I cut the path closer to the male pins which enters to the fridge and solder the resistor. Its working as original one 🤓Service offered 40$ to change it which is very expensive for a single 3030 smd led.
Dear Dukkan. it's likely that it's a constant current source and not a constant voltage source. Best regards
Haha, elegant abgeknibbelt. :) Danke, jetzt habe ich eine Idee wie es geht.
Спасибо огромное. Вы просто выручили. Скоро шаббат, а как убрать свет вообще не было понимая.
If anyone wants to replace only LED element on the board, then you need an SMD LED 3030 3V and 150 mA. (Measured on the original working LED)
You've saved my life 🙂
Nice
I think Siemens could have done that a bit more user-friendly (benutzer-freundlich)
Danke Frank
Danke für das Video. Lichtproblem nach 2,5 Jahren an einem 1000€ Siemens-Kühlschrank.
Leider hat die neue Diode keine Besserung gebracht. Alte wie neue LED leuchten nur ganz minimal in der Mitte. Hat jemand eine Idee, was wir noch überprüfen können? Ich sehe nicht ein, jetzt noch zusätzlich soviel Geld für den Kundendienst zu bezahlen. :-(
Thank you god bless you 😀😀😀
Danke Frank. :-)
Hi, hab mal ne frage wie schauts aus hab ein siemens gerät sieht fast genauso aus wenn ich es bestelle könnte ich es als Laie problemlos auch machen natürlich vorher die Stromversorgung trennen natürlich
Danke dir unsere ist auch runtergefallen 😬😬echt ganz schlecht gemacht von bosch
where is the switch for the light? i don't know the light or switch has problem , thanks
Neither at the door nor the housing i can find a mechanical switch. Guess that there is somewere a magnetic reed contact. Tried to check this by use of a magnet, but without success. Sorry and good luck for the repair.
@@frankh.7959 if leave the door open for a couple minutes, the alarm starts to beep, so I assume it's the light that died, right?
Thanks
Спасибо огромное!
Merci pour le tuto
Impossible supposed to be guaranteed for life of fridge i disagree want to charge R700 outright robbery
wie wechsel ich den nct sensor aus?
Шалом 👋 дякую
Hallo, das Licht in meinem Kühlschrank funktioniert nicht, wo kann ich es kaufen?
Lampenmodul BOSCH 10003924 LED Diode für Kühlschrank
www.ersatzteilshop.de
Gracias
Weiß jemand zufällig wie man hier Thermostat austauschen kann? Habe so ein ähnliches Modell und keinen Plan wo der Thermostat sitzen soll xD
Mit ein dicken Hammer 🔨
Mit ein dicken Hammer 🔨