Nice video. Well explained and shown what to do. Was a bit confused about the half inch spline socket. I used a half inch bihex with half inch drive. Agreed the 13mm bihex is not snug enough. Also, I thought aluminium and steel reacted together (as in the grease, when it dries out). I used copper grease. Good job though.
Great video guys thanks 👍🏻 Just one thing I didn’t understand though, when you installed the ABS ring it didn’t look secure. I assume when it is put on the hub, it will be squeezed secure? That was the only thing I was unsure about, but great video, everything was well explained. Cheers
Just the video I was looking for, I need to replace the rotors and pads on my VM transit. I’m just wondering if it was a duel wheel or not.? Thanks for a great video.
Doing mine exactly as you've done here, except I changed hub seal.. but when I tighten hub nut the wheel stops spinning freely.. Can't for the life of me work out why. No one I know seems to know either. 🤷♀️Any ideas?
I have to replace the wheel studs on my twin wheel 2007 tranny does anybody know the size of the studs and nuts some kind person helped them self to 5 of my wheel nuts and need to repair the damage
Great help, guys. I'm just about to replace the discs and pads on our scout minibus. Saved me a load of head scratching.
Thank you. I’m about to change my Caliper on my transit van and that is a massive help. Mucho Garcia’s
Just doing discs and pads on a Transit Luton van for the first time. spot on chaps massive help :)
Great video, my van just failed MOT with the same problem this is a god send well done both and thank you
I AM SO glad to find this video, thanks a lot guys.
Great job. Very meticulous. Thank you for the education
Just what I needed thanks lads
Nice video. Well explained and shown what to do. Was a bit confused about the half inch spline socket. I used a half inch bihex with half inch drive. Agreed the 13mm bihex is not snug enough. Also, I thought aluminium and steel reacted together (as in the grease, when it dries out). I used copper grease. Good job though.
Good job 👍
Great video
Thanks
Great video guys thanks 👍🏻
Just one thing I didn’t understand though, when you installed the ABS ring it didn’t look secure. I assume when it is put on the hub, it will be squeezed secure?
That was the only thing I was unsure about, but great video, everything was well explained.
Cheers
🙏Danke du bist mein Held🙌🎖
Exactly what I was looking for! Thanks guys!!
What is the torque for the 1/2in. spline bolts?
Great video.
I use copper grease never seen ally grease used before
Good video,did you use new hub nut,and i know you needed to fit pad sensor wire ,but the main thing i learnt is the disc and abs ring removel
What about the paper gasket? Can u reuse it? If so would ya use greese on it to seal it?
I did a job on a old shogun sport exactly the sane thing happened and needed 2 rear calipers and abs pump
Just wanted to add that lock tight is always something to use maybe not for you guys but it helps prevent the bolts rattling lose
Just the video I was looking for, I need to replace the rotors and pads on my VM transit. I’m just wondering if it was a duel wheel or not.? Thanks for a great video.
yeah this is a twin wheel, you can normally tell by the drive shaft he removed, single wheel dont tend to have them
Spot on thanks 👍👍
You’re welcome 😊
Changed both rear callipers, lost 600ml brake fluid. Do I have to pump forever?
Good evening do you know the socket size for the main part of the hub it’s huge
50mm centre nut ?
hi good vid. what size is the large hub nut ?
65mm if youre still looking 2 years later lol
Doing mine exactly as you've done here, except I changed hub seal.. but when I tighten hub nut the wheel stops spinning freely.. Can't for the life of me work out why. No one I know seems to know either. 🤷♀️Any ideas?
Bit late for you but maybe the spacer isn't in the middle of the hub, between the bearings.
What size is that socket? 16:26
I have to replace the wheel studs on my twin wheel 2007 tranny does anybody know the size of the studs and nuts some kind person helped them self to 5 of my wheel nuts and need to repair the damage
Is it the same for a mk7 rwd lwb with 5 studs
Go to Medtec67 he shows both front and rear brakes on a single tire 250 Ford Transit.
As if u wouldn change the inner hub seal 😑
It was made clear that the vehicle owner was penny-pinching.
Lefty tighty righty loosy 🤣🤣
Yes, it is on the left rear hub.
Not on the left side of a vehicle, look at older wire wheel vehicles. Left side is right loosy do to rotation
be cheaper to rebuild the caliper
Try finding a garage who would do it now days
Did you see that thing?