Very nice and honest review. I'm always pleased to see company-provided machine getting an honest review. This helps the company as much as the consumer.
Thank you. I always give my honest opinion on products good or bad. Otherwise there would be no reason to call it a review. If I just reiterate specs then it's a commercial.
Nice, clear presentation. Thank you! I have had my D1 Pro for a week now and am slowly climbing the learning curve, but so far I really like it. During assembly I was surprised to find that the lever adjust knob on the 20W laser module has left hand threads.
As tempting as it is to show these lasers cutting speeded up, it really does a disservice to the potential buyers of these tools. If you are going to show it cutting speeded up, at least tell us how speeded up it is, 2x, 3x. 5x and so on.
First video i watched from your channel and i have to say "well done 👏"! It's so chilled, without fast frame changes or fast talking like others. It is almost like watching a video of Bob Ross 😊👍 instantly subbed 👍 greetings from Germany
Good afternoon, Sorry for bothering you, I bought same laser you have xstool d1 pro I try 100 times to engrave on stainless steel but didn't work I use xtool program But I don't know how to use the right sittings I try to follow all tip on UA-cam but not working 😞 could you please give me some advice or screenshot of right setting or video Best regards
It really depends on the type of wood, what glue they used to make, how humid it is and many other factors. Truly the only way to know for sure is to run some cut tests on it to see how it performs. I suggest faster/more passes over slower/less passes.
Hi, about the xTool D1 pro 20W do you know if it will cut a 1.5 or 2 mm metal sheet? Or aluminum? . I need to make name plates for machine's that we manufacture , so we need to engrave and cut
Hello. I’m afraid it will not cut sheet metal that thick. It might be able to cut .02mm of sheet metal but that’s about it. If you are looking for something that can cut sheet metal you might look into a more powerful fiber laser but those can get pretty pricey for the versions that can achieve that.
Both have their strengths and weaknesses and it depends on your needs as well as your budget but I would have to say I feel the D1 Pro has a slight edge over the LM3 just based on the current setup. That may change as laser module swap outs and things like feet raiser accessories and things like that come out but as they stand today I would say the D1 Pro.
Great review ! Just curious: Is there a "makerspace" where people share plans, like for the box you did with the D1 Pro ? Or any other space for that matter, either free or payed.?
You can check out this website that lists some of the places to get some files. all3dp.com/2/free-laser-cut-files-designs-templates/ I found that box on a site called 3axis.co.
Hello, has anyone stopped the laser while it is working? It stops unfinished and the work is wasted. I don't know what is happening. The controller on the computer gives a message that it has been disconnected.
Only time I have ever seen that happen was when I was using xTool Creative Space. It's only happened to me once or twice but I haven't had that happen in Lightburn. Might be a good time to upgrade and use that software instead.
Honestly I’m not sure. The D1 is not open sourced so can only be run from their proprietary program or ligthburn so I’m not sure if it could run from a raspberry pie.
@@BusterBeagle3D just thinking an Raspberry Pi3 or RPI4 might be more ideal to use, in the workroom than using a laptop. Similar to using Klipper with a 3D printer.
If you are using the 20W version you can feel the surface of an engraving. It's not like a high powered fiber laser but it's also not just a superficial mark either.
I'm not 100% sure but I believe the machine power of the 20W is 120W and the 10W is 60W. At the very least I would think it would require an upgraded power supply. I'm also not sure if they have the specific 20W upgrade module for the pro version. The stand alone 20W on their website is intended as an upgrade to the original D1 and not the pro. Again I don't work for them so I could be wrong.
No. That is a laser module that was just announced a day or two ago. That type of laser is more for metals and is an infrared laser. This is a diode laser and engraves and cuts wood and other materials. It can work on some metals but not precious metals.
My biggest hold-up with these machines is the requirement to use either their tool or a proprietary tool. It would be nice to have other options, even if those turn out to be the best.
Yeah. I'm honestly not sure why they wouldn't make these machines open sourced. It's great that they support Lightburn and it's really a powerful and not expensive program but it would be nice if you could use whatever you want.
Excellent video! While not new to using lasers this will be my first xTool. You mentioned a Facebook group, is there a particular one that is helpful? Thank you for the very helpful information
There are 2 that I would recommend. One is the Official XTool Facebook group and the second is called the XTool owners group. Both have good info in them.
Just make sure when getting a flow control valve the bypass non return valve is in the right direction otherwise you will have full flow without restriction. I use an SMC flow control valve with dial indicator which can be locked in at a preset level; saves a lot of hassle when you find the optimum flow rate. I understand there are new flow control valves with finer control from SMC soon, they are not widely available at the moment.
I m new to laser machine and in market to use for making pop up cards from cardstock paper and some miniature wood pieces. I have Cricut maker machine. 1) does it work on cardstock paper making intricate cuts or too strong for it? 2) other tool air assist or honeycomb is optional in such application? like to try first and gradually like to add accessory. 3) what is longevity of this machine? I read mixed review on amazon 4)Looking at xtool d1 pro 10w or 20w . I see diff of 500 $ between them. Should I go with 20w ? Does 10W cut more intricate cuts then 20w? Quick reply (if u can) will be great as some deal may over soon by cyber monday.
1) It can work on card stock, You just have to lower the power and speed up the cut 2) It usually best to cut with both and air assist (reduces charring on the top surface) and a honeycomb(reduces charring on the back of the surface. Sure you can do it without as well but results may vary. 3) As long as you take good care of it and keep it clean you should be able to get some good use out of it. 4) The 10w has a smaller spot size then the 20W. If you are mainly cutting car stock and thin wood it's perfectly capable of doing that.
@@BusterBeagle3D Thank you for quick reply... Are you suggesting to go with xtool d1 20W or xtool d1 10W based on ur experience ? Thinking between xTool D1 Pro 10W with all accessories (rotary kit, honeycomb, air assist)in 980$ Vs xTool D1 Pro 20W with rotary kit , PRYMOL Air Assist like (55 to 60$),Silicone Sheet (10$) around 1270-1300$
@@uhstube74 It really depends on what you are going to do with it. If you want to cut thicker things go with the 20W , if detail is more important and you want to only cut thin things then go with the 10.
Only real consumable on the laser may be the lens that can get dirty and burned over time. I have seen both the company and other people sell those. As for the laser itself I would assume it could be run for 1000's of hours before needing to be replaced.
I don’t have a glowforge but they are different type of laser. They are a CO2 laser which is much more powerful then a diode laser like the D1. The only other thing I know is that a glowforge requires an active internet connection as that is the only way to operate the machine. So which one is better for you really depends on your needs. XTool does sell CO2 lasers as well comparable to the glowforge so you can always check those out.
That really depends on many factors including what type of wood. what speed/power, air assist or no air assist. I could cut 6mm plywood in one pass where I might have been able to cut 10mm basswood in one. I much prefer more passes at higher speed. Causes much less charring and nicer cuts. As for the life of the laser I'm not sure. My guess if a really long time but if cutting is the primary thing you want to do with a laser I would suggest looking into CO2 lasers.
Seems like they ran into the same issue I had when I built my 2nd upgraded cnc router: I forgot to accommodate the width of the carriage...oops. I wanted my machine to be able to do 36" x 60" but lost 3" on each end of each axis due to the carriage being 6" wide. OOPS. I know they'd have to change all the components and packaging to accommodate the larger laser so it would be costly.
Hi Ryan Thank you for providing a great evaluation of XTool 20 watt diode laser. I am seriously considering replacing a very old but still working 25 watt Co2 machine. My hesitancy with the XTool has been two fold. One is the lack of responsiveness of XTool to my initial contact with them. I’m still waiting. If I can’t get hold of them prior to buying the machine what will it be like when I need parts or perhaps a simple question in the future. As much effort that XTool has put into their marketing I would think they would be equally capable in answering a couple of pre-sales question Two since I do more cutting than engraving. The thickest material I cut (slow speed high power single pass on my Co2 laser) is 3mm MDF and occasionally 1/8th acrylic. I assume the XTool would do it but I am concerned with the kerf. I suppose part of the answer to this would be the diameter of the beam at optimum focus. Ryan if you have any thoughts or answer’s I would greatly appreciate them. For me it’s kind of like a Harbor Freight tool purchase. Some times it turns out to be a great value for the occasional user. But in some cases not. As I stand by for a response from XTool. It may be your opinion that helps me make a yes or no decision on this XTool. Ryan thanks again for posting your experience on UA-cam. In fact if it wasn’t for your particular UA-cam review I wouldn’t be giving this XTool any consideration. I also want to thank you for the other subjects like injection molding. Really helpful to the point information. Anyone interested in learning and actually making some simple injection molded parts should check it out. JoeW
Thank you for the kind words. As for the first question about responsiveness I do hear that a lot and see it many times on the Facebook group. To be honest I feel part of the issue is the volume of requests that they get on any day multiplied by the fact that they are in a completely different time zone. Also I'm guess that since they probably get follow up requests from people who feel that they don't respond in a timely manner that just multiplies the issue. I don't want to make excuses for the company and again I am not part of it but I try to be sympathetic as I also deal with a flood of questions each day over a wide range of things. One way that I do find people get faster respones is to post to their official Facebook groups. The second question about MDF is that this machine should be able to do that all day no problem. Just use an air assist and do be careful if you don't have an enclosure as MDF can be toxic when burned with a laser. The kerf gets blown out by the air assist and I can't imagine having an issue. Now as far as this being a "Harbor Freight" like purchase you just have to keep in mind that unlike Harbor Freight these machines are not cheap. If you are only intending to cut 3mm wood every now and then just about every laser I have reviewed in the past can do that and sometimes at a much cheaper price point. Just something to consider. Thanks again for the watch and plug!
Hey Ryan. Liked your video. I am about to order this. First, where can i get the box file, that is awesome! Second, can i use my Coreldraw with this machine ?
You can use Coreldraw to design something but you would need to be able to load it into either xTool Creative space with an SVG or DXF or into Lightburn in many other formats. They are the only 2 programs that can run this machine. You can find the box file I used here : 3axis.co/laser-cut-mechanical-treasure-box-cdr-file/eo0qxvw1/
Thanks for the honest review! My wife bought me a D1 for Father's Day, but I decided to upgrade from the 10w to the 20w laser. I'm also still waiting on both the laser and the extension arms to be shipped. Frankly, I've found their customer service to be less than I hoped for. From what I've seen and heard, I am not alone in this opinion. Right now, I have several very ex
I wasn't able to get the same result on galvanized steel or aluminum. You would probably be able to mark on it if you treat the surface but I wasn't able to do it bare.
If you check out Colby Schmidt's Etsy page I know that he just released a kit that adds some of these functions to the original D1, Looks sold out currently but might be worth a look into. www.etsy.com/listing/1259041886
I see Xtool is offering the Infared 1064 nm head as a two in one package. The new head is "for all metal". Will this head engrave stainless steel in deep relief? Sorry to be full of questions but I live in the boonies, and this is my best place for finding info. Thanks for any replies.
They are not really limit switches, they are more like an out of bound function, are for the newbies who do not know what limit switches are ...The flame sensor is like on many diodes it's crap...The speed, hahaha, the speed 24k...Who the hell is going to engrave at 24k?You want to put stress on your diode laser , keep engraving over 10k,and you will find out what I mean...I still think that the D1 is one of the best diode lasers on the market today, yes I own one and also have the 20 watt module it works super fine...Anything that the D1 pro can do, I can do better...It's all about knowing your machine and the software you are working with...Like everything in life, there is a learning curve...So start learning!!!
Yeah. I would never recommend burning at the 24K but technically it can work . I use it at a much slower pace. It's just nice to see a laser finally that can do some sort of mark at it's supposed highest speed. Most other lasers I have can't do anywhere near their advertised top speeds.
Very nice and honest review. I'm always pleased to see company-provided machine getting an honest review. This helps the company as much as the consumer.
Thank you. I always give my honest opinion on products good or bad. Otherwise there would be no reason to call it a review. If I just reiterate specs then it's a commercial.
Hi, Does this engrave on Crystal Acrylic? like Awards ? I just want to engrave the name on awards.
Nice, clear presentation. Thank you! I have had my D1 Pro for a week now and am slowly climbing the learning curve, but so far I really like it. During assembly I was surprised to find that the lever adjust knob on the 20W laser module has left hand threads.
As tempting as it is to show these lasers cutting speeded up, it really does a disservice to the potential buyers of these tools. If you are going to show it cutting speeded up, at least tell us how speeded up it is, 2x, 3x. 5x and so on.
Thanks for the honest review! I was thinking to buy CNC router machine but I like xTool D1 Pro 20W. Great video!!!
First video i watched from your channel and i have to say "well done 👏"! It's so chilled, without fast frame changes or fast talking like others. It is almost like watching a video of Bob Ross 😊👍 instantly subbed 👍 greetings from Germany
thank you so much for a great video. I have a question I am confuse which laser cut is good for leathercraft. Please can you help me thanks
Hello, good afternoon, because when I send to record in a rotary system, it takes the image backwards.
Good afternoon,
Sorry for bothering you,
I bought same laser you have xstool d1 pro
I try 100 times to engrave on stainless steel but didn't work I use xtool program
But I don't know how to use the right sittings I try to follow all tip on UA-cam but not working 😞 could you please give me some advice or screenshot of right setting or video
Best regards
Hello. If I remember correctly it was 100mm/m at 100% power that I engraved into stainless steel.
can you do a long burn on this machine like the laser pecker can do using the rotary device ?
No. This machine does not have a roller mode like the Laserpecker 2.
I heard that sculpfun will also produce 20w machine, are you planning to make a comparison video?
I don’t have any plans currently for the sculptfun but you never know.
@@BusterBeagle3D Many of my friends have bought sculpfun and they think it’s pretty good. Hope to see it on yr channel.😍
Thanks for the video. I want to buy one to cut 3mm acrylic in different shapes. You test already this kind of material?
Nice, clear presentation
Im glad I find you Im watching all you videos
thank you
Thanks and welcome!
Excellent review. Thank you
Thank you! I appreciate it.
Another great review Ryan. Well done mate! Nice to see the channel growing nicely ;)
Thank you Sean! I appreciate it. Hope that injection molding machine is still treating you well.
Will this ingrave metal in guns ok?
Can you upgrade the head on the xtool d1 10w with a 20w laser?
You can but you need to get another power supply with it. I believe that xTool sells a kit for that.
How does the D1 work on aluminum? What would the engrave/etch look like?
can you engrave or burn on the table you have this setup on, aka, can i do larger pieces by placing the machine on them and then burn to said piece?
Yes. You can burn directly on a table that you have this machine sitting on. That is how you would create something like spoil board.
how many passes would it take to cut through 1/4 inch plywood?
It really depends on the type of wood, what glue they used to make, how humid it is and many other factors. Truly the only way to know for sure is to run some cut tests on it to see how it performs. I suggest faster/more passes over slower/less passes.
Hi, about the xTool D1 pro 20W do you know if it will cut a 1.5 or 2 mm metal sheet? Or aluminum? .
I need to make name plates for machine's that we manufacture , so we need to engrave and cut
Thank you very much for your support
Hello. I’m afraid it will not cut sheet metal that thick. It might be able to cut .02mm of sheet metal but that’s about it. If you are looking for something that can cut sheet metal you might look into a more powerful fiber laser but those can get pretty pricey for the versions that can achieve that.
Great vid! where did you find the bottom grid that you use as a base for the laser? Thanks
Hello and thank you! I made that grid. You can pick it up here www.etsy.com/listing/1277584267
Curious of your recommendation between this and the Sculpfun S30 pro 20W
I haven’t used the Scuptfun yet. Perhaps one day when I catch up with everything.
Can you buy an extension kit to get a larger cuttin area?
Yes. They do sell an extension kit for this machine.
Merci pour
toutes vos vidéos. Pensez vous
que la xtool d1 pro puisse
remplacer pour la découpe de
15 mm d’une CNC
en terme de rapidité /
passes?
It's hard to tell. You don't have the same charring with a CNC but you can cut things out pretty quickly on a laser.
@@BusterBeagle3D Merci beaucoup !!! 😻
Can this laser do 3d engraving?
Which one do you preffer to work this one or ortur 3?
Both have their strengths and weaknesses and it depends on your needs as well as your budget but I would have to say I feel the D1 Pro has a slight edge over the LM3 just based on the current setup. That may change as laser module swap outs and things like feet raiser accessories and things like that come out but as they stand today I would say the D1 Pro.
can it cut threw a modern license plate?
No. I'm afraid not.
Nice video ! Is it possible to engrave directly on a bigger surface like a table or any furniture ?
Yes. You can directly engrave on the surface the machine sits on.
@@BusterBeagle3D Awesome thank you !
Great review ! Just curious: Is there a "makerspace" where people share plans, like for the box you did with the D1 Pro ? Or any other space for that matter, either free or payed.?
You can check out this website that lists some of the places to get some files. all3dp.com/2/free-laser-cut-files-designs-templates/ I found that box on a site called 3axis.co.
Great review, Thanks!
Hello, has anyone stopped the laser while it is working? It stops unfinished and the work is wasted. I don't know what is happening. The controller on the computer gives a message that it has been disconnected.
Only time I have ever seen that happen was when I was using xTool Creative Space. It's only happened to me once or twice but I haven't had that happen in Lightburn. Might be a good time to upgrade and use that software instead.
Is it possible to use a SBC like a raspberry pie with the D1 Pro? Would that be fast enough?
Honestly I’m not sure. The D1 is not open sourced so can only be run from their proprietary program or ligthburn so I’m not sure if it could run from a raspberry pie.
@@BusterBeagle3D just thinking an Raspberry Pi3 or RPI4 might be more ideal to use, in the workroom than using a laptop. Similar to using Klipper with a 3D printer.
Will this actually engrave stainless steel or does it just mark the surface?
If you are using the 20W version you can feel the surface of an engraving. It's not like a high powered fiber laser but it's also not just a superficial mark either.
I just got a 10W pro, is it possible to just replace the laser with the 20W? Or do you have to buy the whole unit due to extra power requirements?
I'm not 100% sure but I believe the machine power of the 20W is 120W and the 10W is 60W. At the very least I would think it would require an upgraded power supply. I'm also not sure if they have the specific 20W upgrade module for the pro version. The stand alone 20W on their website is intended as an upgrade to the original D1 and not the pro. Again I don't work for them so I could be wrong.
Great Review! Question... is this review for the 1064nm Infrared?
No. That is a laser module that was just announced a day or two ago. That type of laser is more for metals and is an infrared laser. This is a diode laser and engraves and cuts wood and other materials. It can work on some metals but not precious metals.
My biggest hold-up with these machines is the requirement to use either their tool or a proprietary tool. It would be nice to have other options, even if those turn out to be the best.
Yeah. I'm honestly not sure why they wouldn't make these machines open sourced. It's great that they support Lightburn and it's really a powerful and not expensive program but it would be nice if you could use whatever you want.
Hi Ryan, do you know where I can purchase the d1 pro and accessories? I can’t seem to contact anybody on the webpage
Their website works for ordering but you can also order from Amazon if you want to try to get things faster. amzn.to/3AeTNse
ANYONE KNOW IF OR HOW WELL IT MARKS ALUMINUM OR ANODIZED ALUMINUM?
HI Jim, Where do you find your design files, id love to give the chest you made a go!
You can find it here: 3axis.co/laser-cut-mechanical-treasure-box-cdr-file/eo0qxvw1/
would this machine work with laserworks/rdcam.
It only works with xTool Creative Space and Ligthburn.
Excellent video! While not new to using lasers this will be my first xTool. You mentioned a Facebook group, is there a particular one that is helpful? Thank you for the very helpful information
There are 2 that I would recommend. One is the Official XTool Facebook group and the second is called the XTool owners group. Both have good info in them.
please add a link to the air regulator valve. Thanks
It came with another machine I have but this looks to be the same thing. If you have xTools pump you need the 6mmOD one. amzn.to/3BhwI9e
Just make sure when getting a flow control valve the bypass non return valve is in the right direction otherwise you will have full flow without restriction. I use an SMC flow control valve with dial indicator which can be locked in at a preset level; saves a lot of hassle when you find the optimum flow rate. I understand there are new flow control valves with finer control from SMC soon, they are not widely available at the moment.
I m new to laser machine and in market to use for making pop up cards from cardstock paper and some miniature wood pieces. I have Cricut maker machine.
1) does it work on cardstock paper making intricate cuts or too strong for it?
2) other tool air assist or honeycomb is optional in such application? like to try first and gradually like to add accessory.
3) what is longevity of this machine? I read mixed review on amazon
4)Looking at xtool d1 pro 10w or 20w . I see diff of 500 $ between them. Should I go with 20w ? Does 10W cut more intricate cuts then 20w?
Quick reply (if u can) will be great as some deal may over soon by cyber monday.
1) It can work on card stock, You just have to lower the power and speed up the cut
2) It usually best to cut with both and air assist (reduces charring on the top surface) and a honeycomb(reduces charring on the back of the surface. Sure you can do it without as well but results may vary.
3) As long as you take good care of it and keep it clean you should be able to get some good use out of it.
4) The 10w has a smaller spot size then the 20W. If you are mainly cutting car stock and thin wood it's perfectly capable of doing that.
@@BusterBeagle3D
Thank you for quick reply...
Are you suggesting to go with xtool d1 20W or xtool d1 10W based on ur experience ?
Thinking between
xTool D1 Pro 10W with all accessories (rotary kit, honeycomb, air assist)in 980$
Vs
xTool D1 Pro 20W with rotary kit , PRYMOL Air Assist like (55 to 60$),Silicone Sheet (10$) around 1270-1300$
@@uhstube74 It really depends on what you are going to do with it. If you want to cut thicker things go with the 20W , if detail is more important and you want to only cut thin things then go with the 10.
What is the annual maintenance costs and life span of this machine?
Only real consumable on the laser may be the lens that can get dirty and burned over time. I have seen both the company and other people sell those. As for the laser itself I would assume it could be run for 1000's of hours before needing to be replaced.
Hi I'm rather new to the world of lasers but I have a question, Do you think the xTool D1 Pro 20W is better than an glowforge?
I don’t have a glowforge but they are different type of laser. They are a CO2 laser which is much more powerful then a diode laser like the D1. The only other thing I know is that a glowforge requires an active internet connection as that is the only way to operate the machine. So which one is better for you really depends on your needs. XTool does sell CO2 lasers as well comparable to the glowforge so you can always check those out.
What I would really like to know is: how many mm of wood do I cut in a single pass?
What is the lifetime of the diode laser?
Thanks
That really depends on many factors including what type of wood. what speed/power, air assist or no air assist. I could cut 6mm plywood in one pass where I might have been able to cut 10mm basswood in one. I much prefer more passes at higher speed. Causes much less charring and nicer cuts. As for the life of the laser I'm not sure. My guess if a really long time but if cutting is the primary thing you want to do with a laser I would suggest looking into CO2 lasers.
Seems like they ran into the same issue I had when I built my 2nd upgraded cnc router: I forgot to accommodate the width of the carriage...oops. I wanted my machine to be able to do 36" x 60" but lost 3" on each end of each axis due to the carriage being 6" wide. OOPS.
I know they'd have to change all the components and packaging to accommodate the larger laser so it would be costly.
Exactly. Must had looked good in CAD!
Thats such a cool box, care to share the file?
I got it from here: 3axis.co/laser-cut-mechanical-treasure-box-cdr-file/eo0qxvw1/
can you increase the wattage with a new diode laser?
You can swap out the 5W and upgrade to say a 20W version of the xTool diodes but you would also need to upgrade your power supply I believe.
Great video review!
Hi Ryan
Thank you for providing a great evaluation of XTool 20 watt diode laser. I am seriously considering replacing a very old but still working 25 watt Co2 machine. My hesitancy with the XTool has been two fold. One is the lack of responsiveness of XTool to my initial contact with them. I’m still waiting. If I can’t get hold of them prior to buying the machine what will it be like when I need parts or perhaps a simple question in the future. As much effort that XTool has put into their marketing I would think they would be equally capable in answering a couple of pre-sales question
Two since I do more cutting than engraving. The thickest material I cut (slow speed high power single pass on my Co2 laser) is 3mm MDF and occasionally 1/8th acrylic. I assume the XTool would do it but I am concerned with the kerf. I suppose part of the answer to this would be the diameter of the beam at optimum focus.
Ryan if you have any thoughts or answer’s I would greatly appreciate them. For me it’s kind of like a Harbor Freight tool purchase. Some times it turns out to be a great value for the occasional user. But in some cases not. As I stand by for a response from XTool. It may be your opinion that helps me make a yes or no decision on this XTool.
Ryan thanks again for posting your experience on UA-cam. In fact if it wasn’t for your particular UA-cam review I wouldn’t be giving this XTool any consideration. I also want to thank you for the other subjects like injection molding. Really helpful to the point information. Anyone interested in learning and actually making some simple injection molded parts should check it out.
JoeW
Thank you for the kind words. As for the first question about responsiveness I do hear that a lot and see it many times on the Facebook group. To be honest I feel part of the issue is the volume of requests that they get on any day multiplied by the fact that they are in a completely different time zone. Also I'm guess that since they probably get follow up requests from people who feel that they don't respond in a timely manner that just multiplies the issue. I don't want to make excuses for the company and again I am not part of it but I try to be sympathetic as I also deal with a flood of questions each day over a wide range of things. One way that I do find people get faster respones is to post to their official Facebook groups.
The second question about MDF is that this machine should be able to do that all day no problem. Just use an air assist and do be careful if you don't have an enclosure as MDF can be toxic when burned with a laser. The kerf gets blown out by the air assist and I can't imagine having an issue. Now as far as this being a "Harbor Freight" like purchase you just have to keep in mind that unlike Harbor Freight these machines are not cheap. If you are only intending to cut 3mm wood every now and then just about every laser I have reviewed in the past can do that and sometimes at a much cheaper price point. Just something to consider. Thanks again for the watch and plug!
Hey Ryan. Liked your video. I am about to order this. First, where can i get the box file, that is awesome! Second, can i use my Coreldraw with this machine ?
You can use Coreldraw to design something but you would need to be able to load it into either xTool Creative space with an SVG or DXF or into Lightburn in many other formats. They are the only 2 programs that can run this machine.
You can find the box file I used here : 3axis.co/laser-cut-mechanical-treasure-box-cdr-file/eo0qxvw1/
@@BusterBeagle3D Thank You
Great video as always 😊
Could you share where you got the pattern for that groovy box please 🙂
I found it here: 3axis.co/laser-cut-mechanical-treasure-box-cdr-file/eo0qxvw1/
Think you can make challenge coins with this machine?
No. You need a fiber laser for that.
Thanks for the honest review! My wife bought me a D1 for Father's Day, but I decided to upgrade from the 10w to the 20w laser. I'm also still waiting on both the laser and the extension arms to be shipped. Frankly, I've found their customer service to be less than I hoped for. From what I've seen and heard, I am not alone in this opinion. Right now, I have several very ex
expensive but useless boxes in my closet. I am hopeful the remaing parts come in soon. Thanks again for the "warts and all" review.
Nice review. Will it engrave regular steel as well? aluminum?
I wasn't able to get the same result on galvanized steel or aluminum. You would probably be able to mark on it if you treat the surface but I wasn't able to do it bare.
Nice Job. Wish they would release an upgrade kit for my D1 as I have the 20w module for the orig. D1. would like the limit switches.
If you check out Colby Schmidt's Etsy page I know that he just released a kit that adds some of these functions to the original D1, Looks sold out currently but might be worth a look into. www.etsy.com/listing/1259041886
I want this
Good Intel…may want ta remind them not ta use pvc for safety
I see Xtool is offering the Infared 1064 nm head as a two in one package. The new head is "for all metal".
Will this head engrave stainless steel in deep relief? Sorry to be full of questions but I live in the boonies, and this is my best place for finding info. Thanks for any replies.
I would ask around in the xTool Facebook group. I don't currently have the infrared laser module so unfortunately don't know that much about it.
Excelente
They are not really limit switches, they are more like an out of bound function, are for the newbies who do not know what limit switches are ...The flame sensor is like on many diodes it's crap...The speed, hahaha, the speed 24k...Who the hell is going to engrave at 24k?You want to put stress on your diode laser , keep engraving over 10k,and you will find out what I mean...I still think that the D1 is one of the best diode lasers on the market today, yes I own one and also have the 20 watt module it works super fine...Anything that the D1 pro can do, I can do better...It's all about knowing your machine and the software you are working with...Like everything in life, there is a learning curve...So start learning!!!
Yeah. I would never recommend burning at the 24K but technically it can work . I use it at a much slower pace. It's just nice to see a laser finally that can do some sort of mark at it's supposed highest speed. Most other lasers I have can't do anywhere near their advertised top speeds.
👍🏼👍🏼👍🏼👍🏼👍🏼👌🏼🍎😎
16 mn video and not talking about cutting acrylic
Friend,I really appreciate your work. We are looking for reviewers, would you like to review Longer's laser engraver RAY5 10W?