EY3 display has a jumper inside that slots into the same slot the locking device cable goes, no need to have some jumper cables dangling from your scooter.
That's nice to know...I don't think I knew there was a jumper. I guess that wire loop in the JST connector is the jumper you are referring to? I did say to unwrap the coil wire wrap and tuck this inside of that. There would be no dangling anything. While I can make that jumper inside the ey3, many people can not. This was an easy way to solve this issue without taking anything apart.
This is a valid point. In my video I don't say why you should unplug it first and not doing so would cause some significant arcing and possibly damage to connectors and wiring.
Hi, I have a scootet arvala and today the NFC reader decided to stop working, it is exactly the same as the reader you show in your video, so it should work that way right? Cut the wires and connect red to white
Check battery voltage across all 3 wires. You probably have red, black and white, but your EV isn't a Teverun. If you see battery pack voltage across 2 of them...aka black and red probably...that's your 2 battery wires and they shouldn't be connected together as that's a dead short across your battery pack and is likely to cause other problems... like melted wires. The other wire and the positive wire are what you connect together for this bypass.
Thank you so much for answering. So the motor now doesn't work wich I have double motor non of them go. The thing is it has been for a month to a professional e scooter store they try to fix it and they couldn't and I was able to turn it on in 2 hours just from youer video. So I want to make sure that the bypass not the problem and they could cause a new problem. While they tried to fix it. Thank you ❤️
alguien me podría confirmar los colores para hacer el by pass del nfc , porque no lo tengo bien claro del todo , me pareció entender que se juntan blanco y rojo es posible? gracias r@@binandaka6262
Few months ago my Teverun NFC reader also died and I bypassed it by soldering wires together. Last week I upgraded the internal vehicle computer unit - IVCU to the latest model - 4.1.0. and suddenly I could not power off the scooter. Because with new IVCU you turn ON and OFF the whole scooter only with the NFC reader. The power button now does nothing. It only turns off the display but scooter still can be driven.
@@Martin_H.94 I'm betting if you were to look at your original board and the new one, you'd see changes. It's very possible that the enable mosfet is missing and bypassed and that's why it it now stays on. You made physical changes to your scooter that are 100% outside the pervue of this NFC reader bypass!
@@de-bodgery Oh I forgot to mention I got a second NFC reader for free from the seller. But if the new NFC reader breaks I will do something like that.
@@luisalvarocardenaslaupa4841If your EV won't power up, I'll tell you emphatically to bypass the NFC reader like you see in this video! I've now seen dozens of them go bad from just normal use! The shop I do work for, we get new scooters in and the first thing we do is remove/bypass the NFC readers on them! Just today I was working on a Teverun sold before we knew how BAD those damned unreliable those readers are that had a headlight issue. It was 100% operational other than the headlight. I replaced the bad headlight, went to power up and the scooter wouldn't turn on. Right there in my possession for a totally unrelated issue the NFC reader died! It's ridiculous how unreliable they are! Just bypass it!
Theft of this scooter is pretty easy...they don't weigh that much and are not that hard to carry. Having "security" on it so you can't start it is pretty pointless! Never mind just HOW EASY it is to bypass this!
@@de-bodgery Yeah, it's just as easy with most ebike locks... Another question...Have you finished the rewinding of the TP128 yet? Is it running and are you making a video about it?
hi great video, I can ask for help, I lost the NFC key of my Nilox M1 scooter I can make a by pass to make it work, if you want I can send you the photo of the NFC Reader card to understand how to make the by pass thanks
I didn't know what an M1 was so I looked it up before responding. Your NFC reader is built into the display, but exactly how integrated that might be is what will define if you could do a bypass like this. It may be that your NFC reader sends a digital enable code to some CPU in your scooter. In the case of the Teverun, all it's doing is applying pack voltage to the enable circuit in the controller. No data is sent at all so this is a very simple bypass. Bafang used to be very simple and easy to bypass their integration since it was using methods like the Teverun. Now days, the display, pack and controller communicate via canbus and you have to send digital signals back and forth to get the system to enable. It can still be circumvented, but it's a lot harder! *** Have you contacted Nilox? Why not just get a new NFC key? They can't be all that expensive. Most things like this are recorded somewhere so the key combination is known to the manufacturer and then they can duplicate it if needed. It may be that they made like 10 different keys for all of the M1's out there and you just need to get all of the keys until you find the one that works on your scooter. This is a common shortcut! That's what Teverun does...there's only 20 or 25 keys...not sure exactly how many, but it's not a lot.
@@de-bodgery thanks for the reply, I contacted Nilox several times but they told me to send the scooter for assistance and they asked me 100 euros for the key, which is why I was trying to do a bypass, the NFC reader is located near the power button, I'm looking for an alternative in every way, if you have any news remember me thanks
@@frankinocuda Thats RAPE for a sliver of plastic that costs them almost nothing! Clearly a racket! This is exactly why I despise proprietary solutions! So look me up on facebook...Richard Gumfaw. I'll want you to take apart that dashboard so we can look at the circuit board. I can't promise anything right now, but it may be they did a really simple implementation like the Teverun and it's easy to bypass. All I can offer is to look at what you have and maybe it will be an easy thing to fix.
Merci beaucoup !! Je vais essayer ce soir. Ma gt blade ne voulais pas démarrer , la led du lecteur nfc reste éteinte , aucune réaction avec les cartes. Je me suis dit « quelle merde chinoise ! »
@@adrienberreur481 You are THE REASON I made this video! I knew these things fail all the time and I had fixed 2 of them on brand new scooters with this NFC delete. The local shop had lots more of them that were also sketchy. This was a BS add-on anyway!
@@de-bodgery merci à la communauté UA-cam comme toi car avec les chinois on a vraiment des problèmes techniques sans réponses. Merci encore ! Et bonjour de France 🇫🇷 ;)
When i saw the title i unfortunately expected something like this, just like the standard keyswitch switch type of deals, short a wire and go pretty sad in my opinion, they could atleast implement something so the controller itself needs the correct digital signature, but no, ofcourse not well honestly for some brand like Minimotors who still use simple squarewave controllers in their top end models i didn't really expect something else, but still sad nevertheless
Teverun is using the same controllers as minimotors. It's not a new brand with all new designs. It's literally all the same work and designs with a new name on it.
@@de-bodgery yeah thats what i done aswell after first test ride on mine LOL, pretty much instantly ordered FSESC75100 Alu PCB's (MKS version didn't exist yet) and never looked back, apart from wanting some more phase amps but i'm probably not gonna put that effort in THIS scooter would rather buy another one and put my MKSESC75200's in that one (got the 3.3V opamp mod done, which Jaykup described), so got the controllers and connectors ready want a more upgradeable scooter than my Obarter X3, the motor size is good, standard 11 inch (6.5") motors with 145 ish dropout but the shocks are not upgradeable because it doesn't take larger than 100mm, because of the bent down design of the swingarm levers, 125 physically fits but it looks more ridiculous than the unreleased Wolf King GTR in ride height and it's unusable to me lol, also geometry goes to shit in that case so yea first i'll probly buy some different Chinese scooter (probly just an Inxing V5, cause it's a known one and alot of rebrands exist of it, and Inxing actually builds the frames) then fit 125mm Exa's and then look how much space i got in there and order cells and build my own pack for it i want to build/mod a crazy one for the torque mainly, but still controlled in current control mode unlike 99% of the scooter controllers and to stretch the legs of those 75200's to their max capability, might ride for a while on the stock battery tho got the 75100 Alu's because i couldn't get any other ones without getting destroyed by import costs and taxes in my country, the MKSESC 75200 Alu PCB's aswell, since my country has a max import of €150 a piece basically, so if i exceed that it isn't uncommon to pay atleast another €100 on top of the €150 that is import out of the EU basically, since Brexit i can't get a trampa without getting fucked over either. don't even wanna know how much a Trampa would cost me, if it costs €500 price could go up to €800 a piece add 2 together and thats'worth more than the scooter itself by quite a margin
@@BH4x0r I don't know about this op-amp mod you mentioned. Please point me to that wherever I can find it. I have several Flipsky controllers. I'm doing another scooter upgrade to dual Flipsky controllers from the factory trap ones. It's a prototype that never saw production. 8 were made and I have probably the only one in the USA.
lost my nfc card was thinking if hotwiring those cable was doable ! thanks for uploading this man !!
EY3 display has a jumper inside that slots into the same slot the locking device cable goes, no need to have some jumper cables dangling from your scooter.
That's nice to know...I don't think I knew there was a jumper. I guess that wire loop in the JST connector is the jumper you are referring to? I did say to unwrap the coil wire wrap and tuck this inside of that. There would be no dangling anything. While I can make that jumper inside the ey3, many people can not. This was an easy way to solve this issue without taking anything apart.
This is a valid point. In my video I don't say why you should unplug it first and not doing so would cause some significant arcing and possibly damage to connectors and wiring.
Worked for me
Fantastic! why I posted this video!!!
Hi, I have a scootet arvala and today the NFC reader decided to stop working, it is exactly the same as the reader you show in your video, so it should work that way right?
Cut the wires and connect red to white
Check battery voltage across all 3 wires. You probably have red, black and white, but your EV isn't a Teverun. If you see battery pack voltage across 2 of them...aka black and red probably...that's your 2 battery wires and they shouldn't be connected together as that's a dead short across your battery pack and is likely to cause other problems... like melted wires. The other wire and the positive wire are what you connect together for this bypass.
@@de-bodgery I did it, I cut the cable and the wires were red white and black, connect the red with the white and it worked.
It worked for me now it start but now it gives me an error 7 it dosnt Accelerate.
Any recommendation for what should i do next ?
You have some other problem besides a bad NFC reader which you have no bypassed. Do the motors run?
Thank you so much for answering.
So the motor now doesn't work wich I have double motor non of them go.
The thing is it has been for a month to a professional e scooter store they try to fix it and they couldn't and I was able to turn it on in 2 hours just from youer video.
So I want to make sure that the bypass not the problem and they could cause a new problem. While they tried to fix it.
Thank you ❤️
alguien me podría confirmar los colores para hacer el by pass del nfc , porque no lo tengo bien claro del todo , me pareció entender que se juntan blanco y rojo es posible? gracias r@@binandaka6262
Eureka my tall
Few months ago my Teverun NFC reader also died and I bypassed it by soldering wires together.
Last week I upgraded the internal vehicle computer unit - IVCU to the latest model - 4.1.0. and suddenly I could not power off the scooter.
Because with new IVCU you turn ON and OFF the whole scooter only with the NFC reader. The power button now does nothing. It only turns off the display but scooter still can be driven.
Sounds like you need to go back to an older firmware version.
@@de-bodgery It's not the firmware. I physically swapped the computer unit for latest version. Mine was from 1st batch and it had some anoying bugs.
@@Martin_H.94 I'm betting if you were to look at your original board and the new one, you'd see changes. It's very possible that the enable mosfet is missing and bypassed and that's why it it now stays on. You made physical changes to your scooter that are 100% outside the pervue of this NFC reader bypass!
@@Martin_H.94 You could take those 2 wires apart and put a small switch there as your enable and still not have the NFC.
@@de-bodgery Oh I forgot to mention I got a second NFC reader for free from the seller. But if the new NFC reader breaks I will do something like that.
Can you do gyroor hr8
Do what with it?
Hello, could you help me, I have a problem with my blade x scooter.
Where are you located? I jsut had a local guy contact me about one of these. You might be the same person.
@@de-bodgery from Peru. I bought a new scooter with that Teverun NFC and it doesn't read. How can I know if it is properly connected to the scooter?
@@luisalvarocardenaslaupa4841If your EV won't power up, I'll tell you emphatically to bypass the NFC reader like you see in this video! I've now seen dozens of them go bad from just normal use! The shop I do work for, we get new scooters in and the first thing we do is remove/bypass the NFC readers on them! Just today I was working on a Teverun sold before we knew how BAD those damned unreliable those readers are that had a headlight issue. It was 100% operational other than the headlight. I replaced the bad headlight, went to power up and the scooter wouldn't turn on. Right there in my possession for a totally unrelated issue the NFC reader died! It's ridiculous how unreliable they are! Just bypass it!
Reminds me of the good old days when you could use this trick to steal cars, 😂!
Theft of this scooter is pretty easy...they don't weigh that much and are not that hard to carry. Having "security" on it so you can't start it is pretty pointless! Never mind just HOW EASY it is to bypass this!
@@de-bodgery Yeah, it's just as easy with most ebike locks... Another question...Have you finished the rewinding of the TP128 yet? Is it running and are you making a video about it?
@@o.m.2188 No on the TP-128...had to set it aside to get some other stuff done.
hi great video, I can ask for help, I lost the NFC key of my Nilox M1 scooter I can make a by pass to make it work, if you want I can send you the photo of the NFC Reader card to understand how to make the by pass thanks
I didn't know what an M1 was so I looked it up before responding. Your NFC reader is built into the display, but exactly how integrated that might be is what will define if you could do a bypass like this. It may be that your NFC reader sends a digital enable code to some CPU in your scooter. In the case of the Teverun, all it's doing is applying pack voltage to the enable circuit in the controller. No data is sent at all so this is a very simple bypass. Bafang used to be very simple and easy to bypass their integration since it was using methods like the Teverun. Now days, the display, pack and controller communicate via canbus and you have to send digital signals back and forth to get the system to enable. It can still be circumvented, but it's a lot harder!
***
Have you contacted Nilox? Why not just get a new NFC key? They can't be all that expensive. Most things like this are recorded somewhere so the key combination is known to the manufacturer and then they can duplicate it if needed. It may be that they made like 10 different keys for all of the M1's out there and you just need to get all of the keys until you find the one that works on your scooter. This is a common shortcut! That's what Teverun does...there's only 20 or 25 keys...not sure exactly how many, but it's not a lot.
@@de-bodgery thanks for the reply, I contacted Nilox several times but they told me to send the scooter for assistance and they asked me 100 euros for the key, which is why I was trying to do a bypass, the NFC reader is located near the power button, I'm looking for an alternative in every way, if you have any news remember me thanks
@@frankinocuda Thats RAPE for a sliver of plastic that costs them almost nothing! Clearly a racket! This is exactly why I despise proprietary solutions! So look me up on facebook...Richard Gumfaw. I'll want you to take apart that dashboard so we can look at the circuit board. I can't promise anything right now, but it may be they did a really simple implementation like the Teverun and it's easy to bypass. All I can offer is to look at what you have and maybe it will be an easy thing to fix.
Can you do gyroor hr8
Can you do gyroor hr8
Merci beaucoup !! Je vais essayer ce soir. Ma gt blade ne voulais pas démarrer , la led du lecteur nfc reste éteinte , aucune réaction avec les cartes. Je me suis dit « quelle merde chinoise ! »
Easy fix and you will never use the NFC reader again.
@@de-bodgery exactly, now work perfectly
@@adrienberreur481 You are THE REASON I made this video! I knew these things fail all the time and I had fixed 2 of them on brand new scooters with this NFC delete. The local shop had lots more of them that were also sketchy. This was a BS add-on anyway!
@@de-bodgery merci à la communauté UA-cam comme toi car avec les chinois on a vraiment des problèmes techniques sans réponses. Merci encore ! Et bonjour de France 🇫🇷 ;)
When i saw the title i unfortunately expected something like this, just like the standard keyswitch switch type of deals, short a wire and go
pretty sad in my opinion, they could atleast implement something so the controller itself needs the correct digital signature, but no, ofcourse not
well honestly for some brand like Minimotors who still use simple squarewave controllers in their top end models i didn't really expect something else, but still sad nevertheless
Teverun is using the same controllers as minimotors. It's not a new brand with all new designs. It's literally all the same work and designs with a new name on it.
@@de-bodgery yeah the only model i'd consider would be the Fighter Supreme, as it's not the typical squarewave shit, but still expensive
@@BH4x0r My City has dual VESC controllers on it...got rid of those trap controllers ASAP!
@@de-bodgery yeah thats what i done aswell after first test ride on mine LOL, pretty much instantly ordered FSESC75100 Alu PCB's (MKS version didn't exist yet) and never looked back, apart from wanting some more phase amps but i'm probably not gonna put that effort in THIS scooter
would rather buy another one and put my MKSESC75200's in that one (got the 3.3V opamp mod done, which Jaykup described), so got the controllers and connectors ready
want a more upgradeable scooter than my Obarter X3, the motor size is good, standard 11 inch (6.5") motors with 145 ish dropout but the shocks are not upgradeable because it doesn't take larger than 100mm, because of the bent down design of the swingarm levers, 125 physically fits but it looks more ridiculous than the unreleased Wolf King GTR in ride height and it's unusable to me lol, also geometry goes to shit in that case
so yea first i'll probly buy some different Chinese scooter (probly just an Inxing V5, cause it's a known one and alot of rebrands exist of it, and Inxing actually builds the frames) then fit 125mm Exa's and then look how much space i got in there and order cells and build my own pack for it
i want to build/mod a crazy one for the torque mainly, but still controlled in current control mode unlike 99% of the scooter controllers and to stretch the legs of those 75200's to their max capability, might ride for a while on the stock battery tho
got the 75100 Alu's because i couldn't get any other ones without getting destroyed by import costs and taxes in my country, the MKSESC 75200 Alu PCB's aswell, since my country has a max import of €150 a piece basically, so if i exceed that it isn't uncommon to pay atleast another €100 on top of the €150
that is import out of the EU basically, since Brexit i can't get a trampa without getting fucked over either.
don't even wanna know how much a Trampa would cost me, if it costs €500 price could go up to €800 a piece
add 2 together and thats'worth more than the scooter itself by quite a margin
@@BH4x0r I don't know about this op-amp mod you mentioned. Please point me to that wherever I can find it. I have several Flipsky controllers. I'm doing another scooter upgrade to dual Flipsky controllers from the factory trap ones. It's a prototype that never saw production. 8 were made and I have probably the only one in the USA.