I think those are isolated ones. He used soldering iron on tips of the wires to remove it. You can actually see it in beginning when he prepared rp2040 chip
Hello sir, thanks for the video! I want to ask that are there something that must be install on that chip before we do this progress? Or we just do this after we bought the chip? (I'm new to this kind of thing... sorry about that...)
You did not remove the micro-usb port or the boot/reset buttons, but you already flashed the chip, were you making sure that it worked and planning on removing or just leaving in place ?
You know this was a test and not a tutorial right? I made this video just days from picofly release. Of course installation with intention to be permanent will be void of the buttons and the Port
Why did you make such a great video only to make it unwatchable with this flashing graphic? Maybe others can handle it, but yeah I don't understand 🤷♂️
Üdv! Én régebben hwfly modchipet telepítettem a switch liteomba, egyszer majdnem el is rontottam de egy jó küzdelem után végülis sikerült. Nehezebb mint aminek tűnik az a nagyon fontos ebben.
@@prmzngph In my case i burned off a pad from the dat0 cmd clk rst flex cable (the other flex cable that came with the hwfly kit). Thankfully after i exposed the trace and wired it to the pad it worked fine.
Its part of the modchip you get. You just need the soldering tools and wire and a trywing screwdriver which is Nintendo's type of tool to unscrew the screws.
Having a bit of trouble finding info on this but, when the chip is installed, what can you do with it? I know you can run a program called atmosphere off a microsd card, however, is this something where you have to boot it with your pc or rcm jig, or any quirks like that? Im planning to pay someone to mod mine, and would appreciate the info 😅
Hello! Can you please tell me if it is possible to use some kind of analogue of this mosfet, for example FDS8884? And how critical is the replacement of the mosfet with analogues? What parameters should be considered when choosing a mosfet?
Thanks for showing this Definitely not worth all this work, just buy an old switch and you will avoid unnecessarythings to do like this. We will have to wait for someone to make it easier and less dangerous.
hwfly source code is open source. the firmware for rp2040 and its magic was made by rehius. gdfchip will use normal HWFLY firmware whilst rp2040 based chips even in hwfly form factor will use picofly firmware
@@prmzngph sorry, I mean the fw that flashed in chip. Its says hekate-nx so its hwfly-nx fw right ? I think if that picofly fw it will have bee picture on bootloader when you not insert the microsd.
BL TEC na area...kkkkk onde eu encontro mais informaçãoes.. tipo fw, diagrama etc.. para inserir nesse chip vc sabe? estou caçando aqui pra colocar um console meu pra teste... e quem sabe num futuro proximo para clientes.
Bro I need your help please I just buy picofly today do I need to download a software on it before I install it on switch lite or I can do that later after I install it on the switch lite ?
@@prmzngph Ah, makes sense. I attempted to do this last night and failed. The chip will blink blue, white, then blink blue for a while, then red before shutting off. Not sure what I did wrong. I just get a black screen as well. May need to check my soldering, I thought it was good. is there a way to verify with a voltmeter or something that your soldered correctly? I tested for conitnuity but that may not be enough. Also, do you need to pre-tin your wires? I find them hard to stick sometimes. EDIT: Now I'm thinking it might be my DAT0 cable? That one was hard to put on and I couldn't tell if it was touching the other two connections nearby, they're so close together.
if it's light blue then it's your cpu wire /going in to the mosfet. pre-tin is a must on any connection. you want as little heat on the pads so you prep your stuff before attempting to solder. dat0, clk, cmd should have 400-800 value in diode mode. but based on your led result. probably cpu wire
@@prmzngph Can I send you a picture when I get home? I put it under a microscope and it looks good to me but, maybe I'm blind. You said diode mode can help me check?
@@prmzngph thanks! 😁 I'va already placed an order for V1 and V2 Flex... I'll try using an RP2040-One instead of Zero..hopefully it'll work with only 2MB flash... 😅
I ended up losing the capacitor when soldering the 3v3 point, does anyone know what its value is to put another one in its place, thank you very much!!
Ok that's it ...I am getting into microsodering...
Same here.
just bought all the supplies to do this lol
How did it go? I'm literally considering doing this as well but the I'm thinking I'll definitely break my switch lol.
@@pspisking It's definitely harder than it looks. I managed to do it successfully on mine when hwfly was the only one available but i almost broke it
Nice!! What type of wire did you use? Any diagrams to see the soldering points?
Hola cavernícola ! El diagrama está por ahí hace rato ! 😉
Yakara subió una imagen y la guarde :)
Ojo que es inestable por el momento!!!!
@@heeliiopoodeer A que te refieres ?
@@heeliiopoodeer inestable en qué sentido? En hardware o software?
One day I hope the switch lite can be software modded, because it would be such a good hacked handheld
Never it would be I suppose since there should be an entry point to hacking which itself is blocked. The entry is provided by hardware module.
amazing...how is it you're not using any microscope?
also the wires seemed to have no coating, won't they short among themselves if tangled?
I think those are isolated ones. He used soldering iron on tips of the wires to remove it. You can actually see it in beginning when he prepared rp2040 chip
@@fluxion767 I see. Totally missed that. Thanks! 😁
@@luqmanmohd2737 no problem :). I am thinking about doing this mod myself
Don't you have to unsolder the voltage controller, USB port and buttons from the RP2040 to make it fit?
just the port and buttons.
on the lite you can actually get away with retaining the port if you modify the backplate.
Dito ko nabili yung v2 ko!!! Galing talaga!🙌🏻🙌🏻🙌🏻
Magkano magpa mod ng lite sa kanila?
Hello sir, thanks for the video! I want to ask that are there something that must be install on that chip before we do this progress? Or we just do this after we bought the chip? (I'm new to this kind of thing... sorry about that...)
yes you have to flash the chip first, i suggest googling for a more in depth tutorial to use alongside this video
You did not remove the micro-usb port or the boot/reset buttons, but you already flashed the chip, were you making sure that it worked and planning on removing or just leaving in place ?
You know this was a test and not a tutorial right? I made this video just days from picofly release. Of course installation with intention to be permanent will be void of the buttons and the Port
Vamosssss Pico Flyyyyy !!!!
Do you use microscope? or just see your as eyes?
thanks you, bought a soldering iron and installed it myself with your viedo! ^-^
any prior soldering experience?
Love the Luffy beats Crocodile theme
Hi master. How can I flashing FW for picofly . and should I doing bridge two pin until workings . Sorry for weak my language
Excelentes noticias 😍
Can you also mention the link to buy this mod from? Thanks for the video.
Why did you make such a great video only to make it unwatchable with this flashing graphic? Maybe others can handle it, but yeah I don't understand 🤷♂️
Do you think it's worth a try if you've never soldered in your life?Or is it just for tech-gods?
Please don't try this if you've never soldered before, just ask your local repair shop
If you have never soldered do not do this. Test out soldering on a broken DVD player or some cheap crap electronic device.
My hand is shaky. I aint trying
I installed a hwfly before, its definitely harder than it looks for a beginner. I'm getting the hang of it though.
Szia! Hol vetted a chipet? AliExpress? Nehéz megcsinálni?
yes, also check your local suppliers.
Üdv! Én régebben hwfly modchipet telepítettem a switch liteomba, egyszer majdnem el is rontottam de egy jó küzdelem után végülis sikerült. Nehezebb mint aminek tűnik az a nagyon fontos ebben.
@@kozakalex222222 yes it's important not to use thick wires, the switch lite pads are sensitive
@@prmzngph In my case i burned off a pad from the dat0 cmd clk rst flex cable (the other flex cable that came with the hwfly kit). Thankfully after i exposed the trace and wired it to the pad it worked fine.
what is that black cable called at the starting of the video ? 4:39
Its part of the modchip you get. You just need the soldering tools and wire and a trywing screwdriver which is Nintendo's type of tool to unscrew the screws.
Having a bit of trouble finding info on this but, when the chip is installed, what can you do with it?
I know you can run a program called atmosphere off a microsd card, however, is this something where you have to boot it with your pc or rcm jig, or any quirks like that?
Im planning to pay someone to mod mine, and would appreciate the info 😅
you totally don't need rcm if you already have a hard mod like this
Hello! Can you please tell me if it is possible to use some kind of analogue of this mosfet, for example FDS8884? And how critical is the replacement of the mosfet with analogues? What parameters should be considered when choosing a mosfet?
close spec to alltransistors.com/mosfet/transistor.php?transistor=12880
@@prmzngph thanks
*AMAZING !!* 🙌🏻
Where did you get the Picofly from?
Cam you close it back with the USB and buttons on?
i no have the flex, can i do with just mosfet N.. ? some tips.
Thanks for showing this
Definitely not worth all this work, just buy an old switch and you will avoid unnecessarythings to do like this.
We will have to wait for someone to make it easier and less dangerous.
You lost me at buy
you don't have to do this. you pay someone to do the service.
@@mrwoodcat you lost me at pay
is the picofly recommendable? I don't know if I trust it enough that it wont brick my switch after a couple of months installing it
Well as long as you dont go online your fine. Otherwise nintendo will ban your switch.
@@AttractionSpot I'm talking about as an hardware standpoint, is it stable enough for it not brick my switch etc.
Hi... just to make sure, so you use hwfly-nx fw v0.7 on this pico chip ??? So rp2040 can work with hwfly fw and pico fw ???
hwfly source code is open source. the firmware for rp2040 and its magic was made by rehius.
gdfchip will use normal HWFLY firmware
whilst rp2040 based chips even in hwfly form factor will use picofly firmware
@@prmzngph so which one do you use in this video ? Im so confuse
@@prmzngph so simply, we can use hwfly-nx on rp2040 chip and use pico fw on hwfly chip ?
@@tanji8592 I'm not sure how you can be confused, the video install is clearly picofly, no you cannot use HWFLY firmware on picofly.
@@prmzngph sorry, I mean the fw that flashed in chip. Its says hekate-nx so its hwfly-nx fw right ? I think if that picofly fw it will have bee picture on bootloader when you not insert the microsd.
I have never used a soldering iron will I be able to do what you taught?
Definitely NOT! Ask a local repair shop to do it for you!
Great video it will definitely help
He try open sp1 little bit by twezer that meaning v2 Flex Cable not fit on lite cpu?????
do you have the source code? I know it's not open-source could you tell me where to get it?
BL TEC na area...kkkkk onde eu encontro mais informaçãoes.. tipo fw, diagrama etc.. para inserir nesse chip vc sabe?
estou caçando aqui pra colocar um console meu pra teste... e quem sabe num futuro proximo para clientes.
Já tem o site que com os diagramas e firmware. Mas não sei como compartilha aqui no comentário o link do site...
hello!!where to buy a picofly for switch lite?
Is the chip need to be flash before installation bro , or its already have frimware on it
you need to flash it with a small 200kb file and i don’t know where to get it but can you tell me the name of the cable he is working on at 4:25 ?
@@amankmr03 it must be the ribbon cable from hwfly.
@@BaDRuleTR is there any name of this cable if i only need this particular ribbon cable ?
@@amankmr03 yes, hwfly v2 flex cable.
@@amankmr03 GBATemp has a tutorial on this.
Bro I need your help please I just buy picofly today do I need to download a software on it before I install it on switch lite or I can do that later after I install it on the switch lite ?
Got ignored
you didnt need the dat0 contact under the emmc? i thought you need it
I think that's just for the OLED models.
hi.what is this stuff you re using to lock the picoflasher so it doesn t move?
just a normal double sided tape
Why did you remove the EMMC cover?
so i can have a better view 😅
@@prmzngph Ah, makes sense. I attempted to do this last night and failed. The chip will blink blue, white, then blink blue for a while, then red before shutting off. Not sure what I did wrong. I just get a black screen as well.
May need to check my soldering, I thought it was good. is there a way to verify with a voltmeter or something that your soldered correctly? I tested for conitnuity but that may not be enough. Also, do you need to pre-tin your wires? I find them hard to stick sometimes.
EDIT: Now I'm thinking it might be my DAT0 cable? That one was hard to put on and I couldn't tell if it was touching the other two connections nearby, they're so close together.
if it's light blue then it's your cpu wire /going in to the mosfet.
pre-tin is a must on any connection. you want as little heat on the pads so you prep your stuff before attempting to solder.
dat0, clk, cmd should have 400-800 value in diode mode. but based on your led result. probably cpu wire
@@prmzngph How do I test the soldering on my hwfly cable?
@@prmzngph Can I send you a picture when I get home? I put it under a microscope and it looks good to me but, maybe I'm blind. You said diode mode can help me check?
...ohh, so its not necessary to use Switch Lite (specific) CPU Flex Cable...🤔🤔🤔
you can even use v1
@@prmzngph thanks! 😁 I'va already placed an order for V1 and V2 Flex... I'll try using an RP2040-One instead of Zero..hopefully it'll work with only 2MB flash... 😅
Nice. Lupet mo IDOL parang gusto ko tuloy pag experimentuhan ang lite ko. KUDDOSS!!
Do you get nand read writes errors without the 470 resistors???
it's a requirement. you will get emmc errors and possibly fry the emmc if you don't use
Where Can I Buy One Of Them Picoflys?
How much it cost to you all the stuff?
Its like $7 for the chip.
Wow, that's pretty cool!!
Link for the resistors please
450
@@Alan-jz1rl cant find 450, will 430 or 470 work?
@@everyonesweird8219 saw a video with 470 resistors working fine
Are you not using microscope?
@@galihpratama2295 it's easy to do without a microscope if you're used to doing it. But sometimes I use to check my work
@prmzngph an absolute beast when jumpering without microscope
is there really no other 3.3v point to use? that's the scariest one
there's on beside the wifi chip shield.
@@prmzngph where can I see a pin out??
@@Sonickart it's easy to spot, the right square shield above the charge port is the wifi chip. the pads on the left are ALT 3V
I ended up losing the capacitor when soldering the 3v3 point, does anyone know what its value is to put another one in its place, thank you very much!!
Amazin! where can I buy the modchip?
Thats the hard part since its not legal to sell the modchips.
Aliexpress
That's not a modchip. It's just a rp2040 zero. A very common microcontroller that's cheap.
Qué tal mi amigo puede hacer un video donde le instale el hardware para conectar la swich ala tv
Flux type\brand?
Props 👏👏🦾
I don't see uf2 file link 😢
Anywhere we can get MOSFETS from hwfly?
Should have closed the back shells up in the video.😂
No la puede cerrar porque picofly tiene un USB tipo c que molesta
@@heeliiopoodeer it’s kinda pointless until we can figure a solution for that
@@Deccrr What are you talking about, it can be removed with heat.
is this possible with the oled as well?
and what ribbon cable's do i need to order?
There's no ribbon cables you have to take apart your switch and solder wires to the motherboard. Its not plug and play.
Yes you can its kinda the same process but if you want the easiest way you need a 1st gen switch
what resistors are that?
0603 SMD type, between 47-240 ohms
Could you make the code or source file available where I can get it.. I would like to do it on my oled switch for test. thanks
GBATemp has a thread about this.
Do Oled
colega donde encuentro los archivos para pico fly gracias de antemano
oh wow it's pure hell
Hay un poco de vídeo en tu marca de agua.
Does this work for the V1 Versions?
Yeah
nice
chinese hwfly sellers are coping and seething rn
Teve que comprar o chip picofly e o outro flat preto né? Eles vendem separado?
Bro is this working on switch lite version 16.0.2
It will work on any software version since it is a modchip.
Fino meu jovem.
Boss anong gamit mong wire?
0.16mm 35awg
A happy day !!!
Magkano po yan boss?
diagram please
Where do we buy these parts???
Thats the hard part since modchips arent legal.
Que venham os kits.
where do i buy from
Thats the hard part since its not legal to sell modchips.
vid needs audio even if its static
how hard is this?
Really hard espacially if you have never soldered before. This is micro soldering which is harder. You It would help to have a magnifier.
pinoy pala tuh. akala ko indiano nanaman . patuts lods may switch lite din ako baka naman
ang galing boss.
I must buy it
I dont have the balls or tools to install a modchip :(
Amigo yo quiero comprar uno puedes mandarlo para america
get that hashtag out of here dude
🤗
Este video va a subir en views muy muy rapido / This video will have a lot of views too fast.
AMAZING!!!!!!
Walter
Ya tengo la placa RP2040 pero creo que esperare a uno o dos meses a que sea mas estable. Saludos
Que tal, donde la compraste? Me podrías asar el dato? Muchas gracias
@@BalamV28 Mercado Libre / $700 pesos Mexicanos, hace 3 meses, ahorita ya andan entre $900 y $1000
@@vellagarto38 Muchas gracias, sabrás de alguna página qué envié a USA?
@@BalamV28 amigo en Aliexpress los tienes a 4 euros
Ahora si todos con Swich modificada
excelente !!!!!!!!!!!!!!!!!!
Quais os materiais para esse desbloqueio? E quais update ele já aceita visto que já estamos na 16.
La música...que no le gusta a NINTENDO!
any diagram about soldring point plz
alguem ai conseguiu ver quais são os valores dos resistores?
47 a 50 ohms!
picofly zero dislike
it's day0 installation just when it came out
👏👏👏👏👏👏👏👏👏
👿
Los cables van a hacer corto circuito 😨, no tienen protección.
Están esmaltados
日本人いる？😮
🤣🤣🤣🤣 esto se complicó
Yo sé, quise que hackear mi switch pero es demasiado complicado