Sir., I have implemented the same way u have done but unable to get the output..it's showing some errors in the integrator block,.. could u please check?
Sir, i have 2 questions 1) what is the rating of statcom and how can I identify it from the video simulation ? 2) Why you haven't used a coupling transformer with statcom?
16:36 there is a mistake, you should remove the IDL from there and only leave ID. as explained in the begining of your video. Thanks allot for your time and efford :)
Thanks for the great video! It sounds better now that you included commentary instead of just computer screen. Could you please explain how you defined the PID gain values? Was it calculated or just by trial and error? Best regards!
Thankyou for the video, its been really helpful. Along with the reactive power compensation, I want to supply active power from battery at the time. Can you please help me with the modification that is required to be made? I would be very thankful for your any kind of assistance.
Thank you so much for your great effort. In my research I need to design a SSSC rather than using the already exists Simulink Phasor type one. Could you help???
Hai!! This video is great! Thank you. And can i know how can I select/calculate the value of the capacitor for Vdc? I am trying to make a shunt active power filter for 33kV system. Thank you!
Excellent. Your job is very good for STATCOM. One question, if you put a three phase fault on it can it control the reference voltage again? If it works for transient voltage recovery or you can modify it I will pay for this. Let me know if you are happy to make some profit.
Sir., I have implemented the same way u have done but unable to get the output..it's showing some errors in the integrator block,.. could u please check?
Sir, i have 2 questions 1) what is the rating of statcom and how can I identify it from the video simulation ? 2) Why you haven't used a coupling transformer with statcom?
Thank you so much...can u explain designing sliding mode control for this statcom...your way of showing the program is easy to follow that's why i am asking you....if u don't mind plz explain....
Great tutorial sir! I wanted some help with how can I add a constant length transmission line in this circuit with which I can simulate the effects of STATCOM at different locations in the grid.
Thank you, sir, for explaining the STATCOM. but when I trying to simulate my simple STATCOM with a series reactor module in Matlab it does working properly. This means every time I get a different reference signal. I am also getting confused in the controller (means you use that divide Vdc block). Can you please tell me what you think about it,
Sir, actually I am asking that, what happens when simple series reactor (RL) filter is used. And how can I select the capacitor value and voltage value across a capacitor? Means I have also created a STATCOM model in Matlab but, it doesn't work properly.
Hello sir, I have a master’s project, which is to add a STATCOM device on the 132 kV line to raise the voltage and reduce the REACTIVE power. Is this video useful for me in implementing the project or is there another plan to implement what is in my project THANK YOU FOR the answer
Sir, I am not able to get same active power for load and source but remaining all are correct ..can u please help me out By the way nice video sir keep making videos like this.. I and my friends like ur style of teaching
sir I followed all the steps and modeled but VDC is fluctuating, unable to regulate to 800V , the statcom is also not compensating properly. can u please fix this error?
Sir , 1. If i eleminate the Controller what happens . 2.with controller we are getting spike over there how can we do this simulation to without getting spike
@@TechSimulator please sir its a humble request can you do it within a month or share svc model I have to submit it for Final year project please plz sir.
Hey, Great Video.. Learn Many things . Could you Please make a video on STATCOM application for Transient Stability Improvement. or just suggest what changes required in video model so that we can see performance of system during fault condition.
Thank you so much...can u explain designing sliding mode control for this statcom...your way of showing the program is easy to follow that's why i am asking you....if u don't mind plz explain....
If you like my work, please do consider subscribing to this channel.Thank you. ua-cam.com/channels/58DFky5Fm9AxH9UmWHHYmQ.html
Sir, while simualating the same, i found the following error
Error in port width of dimensions, invalid dimension has been specified for input port
Sir., I have implemented the same way u have done but unable to get the output..it's showing some errors in the integrator block,.. could u please check?
Sir, in your video, the current waveform has a magnitude of 420A whereas the voltage is 340v. How can grid current be so high? kindly clarify
Sir, i have 2 questions
1) what is the rating of statcom and how can I identify it from the video simulation ?
2) Why you haven't used a coupling transformer with statcom?
sir/mam your works regarding multiple areas of power electronics are very helpful for all students and researchers
thank you
Wow this has really help reduce my final project pressure
Perfect explanation.... You deserve lots of respect..
Thanks a lot sir/mam . this video helped a lot,. Could you mind sharing complete simulation of UPFC
Very good
16:36 there is a mistake, you should remove the IDL from there and only leave ID. as explained in the begining of your video.
Thanks allot for your time and efford :)
Yes Sir! I love it, thank you very much.
🙏🏻
@@TechSimulator Hi sir! Could you give me mathematic modelling that you did? Thank you very much. My mail maxterkeylp@gmail.com
Thanks for the great video! It sounds better now that you included commentary instead of just computer screen.
Could you please explain how you defined the PID gain values? Was it calculated or just by trial and error? Best regards!
I am glad that you liked my video
Choose a time constant for voltage and current controller. 1 ms for voltage controller and 200 microsecond for current controller would be fine
To find kp for voltage controller, divide dc capacitor with time constant
To find kp for current controller divide filter inductor with curreaponding time constant
Ki values for for both controller initially kept at zero, then start increasing gradually untill staedy state erroro becomes zero
Well done, thanks for your effort
🙏🏻
Thankyou for the video, its been really helpful. Along with the reactive power compensation, I want to supply active power from battery at the time. Can you please help me with the modification that is required to be made? I would be very thankful for your any kind of assistance.
Is this STATCOM applicable in 3 phase sytem in transmission 5 bus system and more.
If no please guide
yes
Hello sir, will you tell me the SVC coordinates? SVC works on which coordinates?
Thank you for the video.please can you tell me why you put value 2 with gain in the controller
..
Will you please do a video on compensation of voltage flicker by using statcom
Thank you so much for your great effort. In my research I need to design a SSSC rather than using the already exists Simulink Phasor type one. Could you help???
In the last loop of current control before converting to dq axis why are u multiplying by 2/Vdc as we get Vd, Vq directly from them?
I have made a seperate video on this pls do watch
@@TechSimulator can you share the link or description of it?
Hai!! This video is great! Thank you.
And can i know how can I select/calculate the value of the capacitor for Vdc? I am trying to make a shunt active power filter for 33kV system. Thank you!
it involves lots of things. please refer some papers on the topic
Amazing!
How do we connect the induction motor as the load in this circuit? Will the circuit work for variable load induction motor as well ?
Which matlab version you are using
this is made using 2018a
Excellent. Your job is very good for STATCOM. One question, if you put a three phase fault on it can it control the reference voltage again? If it works for transient voltage recovery or you can modify it I will pay for this. Let me know if you are happy to make some profit.
Sir., I have implemented the same way u have done but unable to get the output..it's showing some errors in the integrator block,.. could u please check?
Nicely presented
Thank you
Sir, i have 2 questions
1) what is the rating of statcom and how can I identify it from the video simulation ?
2) Why you haven't used a coupling transformer with statcom?
rating and design values are given at the begning of the video.
you can have statcom with or without coupling transformer
@@TechSimulator Thank You very much.
Hello sir...
Please show me where u have connected the load?.
I really like the way you are explaining, please is it possible to use for ieee 15 bus reactive power compensation ?
1. Why you are taken Lg=Linv, could you please tell me?
2. Why you have not used any capacitor at DC side of the inverter
Hello,
Do you happen to have this file? I keep getting the error, running continuous elements and I cannot fix this error.
Thank you so much...can u explain designing sliding mode control for this statcom...your way of showing the program is easy to follow that's why i am asking you....if u don't mind plz explain....
thanks for your video sir.. Can this simulation use to mitigate voltage sag under different fault sir?
No
Hey, love your content! Could you please make a video on Modular Multilevel Converter (MMC) using Phase Shifted Pulse Width Modulation (PS-PWM)?
Will try to make. Thanks for your suggestion
Can you please specify which version of matlab is used?
Great tutorial sir! I wanted some help with how can I add a constant length transmission line in this circuit with which I can simulate the effects of STATCOM at different locations in the grid.
you can contact me at my email
@@TechSimulator can u share your email please
Sir, in your video, the current waveform has a magnitude of 420A whereas the voltage is 340v. How can grid current be so high? kindly clarify.
Current is decided based on the power requireemnt. NOt based on the voltage
@@TechSimulator Thank you very much
Thanks for the wonderful video. Can you explain why ode23t solver is used.
Thanks for the video....
🙏🏻
Do you research paper for this simulation?
Hi i tried this simulation but didn't get the output like you can u please help
me too
Thank you, sir, for explaining the STATCOM. but when I trying to simulate my simple STATCOM with a series reactor module in Matlab it does working properly. This means every time I get a different reference signal.
I am also getting confused in the controller (means you use that divide Vdc block).
Can you please tell me what you think about it,
Sorry i didnt get your question
Sir, actually I am asking that, what happens when simple series reactor (RL) filter is used.
And how can I select the capacitor value and voltage value across a capacitor?
Means I have also created a STATCOM model in Matlab but, it doesn't work properly.
Thanks for doing my need ..
Wat s last scope waveform I mean DC bus voltage waveform? What it is ?
It is the voltage across the inverter input capacitor
@@TechSimulator s..I got it.Thank you very much
I have problem with grid current I did same silmulation but grid current is about 4000 A why?
Hey can this compensate non linear and unbalanced load ?
No. We need to modify the controller. I am trying to do it, if i get proper output then will post the video
@@TechSimulator thank you
@@TechSimulator waiting for your video
@@TechSimulator Any updates for compensation on non linear loads such as a loaded induction motor, sir?
Can we make this as Pv statcom yo control reactive power in night or when there is disturbance it fed that power for few seconds to compensate fault.
this is only used for reactive power compensation, and that can be done in the night also.
Can u give a outline about controllers for inverters and grid.
sir, please can you explain low voltage ride through in PV inverters with simulation?
I will try to make
Hello sir, I have a master’s project, which is to add a STATCOM device on the 132 kV line to raise the voltage and reduce the REACTIVE power. Is this video useful for me in implementing the project or is there another plan to implement what is in my project THANK YOU FOR the answer
Hello sir, I would like to know if you have implemented your project?
@@josuekayembe6129 hello sir, no ihave not yet implement
Alright. I had almost the same project but I have implemented and it’s working.
@@josuekayembe6129 can you help !!
@@josuekayembe6129 hello sir!
Please Sir can you share the simulink circuit diagram and data ?
Sir can you make bidirectional converter?
Can the same simulation be used for realizing dstatcom ?
yes. most of the things
@@TechSimulator can you make a vedio on that too?
Sir, I am not able to get same active power for load and source but remaining all are correct ..can u please help me out
By the way nice video sir keep making videos like this.. I and my friends like ur style of teaching
Thank you man
Respected sir, I request you to please make vdo on extreame fast charging of electric vehicles please sir
sir I followed all the steps and modeled but VDC is fluctuating, unable to regulate to 800V , the statcom is also not compensating properly. can u please fix this error?
Did you get the output?
Thank you sir
Sir , 1. If i eleminate the Controller what happens .
2.with controller we are getting spike over there how can we do this simulation to without getting spike
Pls share your model at my email
@@TechSimulator sir can you please mention your mail id
What to do for DSTSTCOM
Sir can you please do Reactive power compensation on SVC?
will try to make
@@TechSimulator please sir its a humble request can you do it within a month or share svc model I have to submit it for Final year project please plz sir.
@@thehaseeb9136 Have you performed reactive power compensation on SVC. if yes I need guidance.
Hey, Great Video.. Learn Many things . Could you Please make a video on STATCOM application for Transient Stability Improvement. or just suggest what changes required in video model so that we can see performance of system during fault condition.
Yes sir it would help us alot
Can we simulate STATCOM with out controller ....
What you mean by without controller?
@@TechSimulator means STATCOM has to operate jus by pulse generator alone .....
That is not possible
How to measure then for 1minute and so , I mean large time data, if sampling time is 1micro second
Sir i need this simulink
It's available on net as MATLAB simulink
Sir can please mention the refference paper or base paper
Hey, did you get the reference paper? If yes, can you share it please
Thank you so much sir.. how can i talk to you please ?
Sir, Can you email slx file. i am trying to simulate but not getting good response.
Hi, thanks alot for this informative video. I have implemented, but couldnt get the results. Can I send you file to have a look please?
sure. please send the file, i will have a look
@@TechSimulator thanks for the reply, i have sent the file for your consideration plz....
What is mode of communication (email or number) please can u share one I have also file to share with sir.?
hello bro I have also implemented but I cannot get the same result I would like to know if you have fixed the issue?
@@shahkhan110 Did u get the right result?
I am not getting the result which is shown here
What you present here is different with Simulation results. This model has a bug and not working properly.
We need sssc analysis using pi controller
hi i tried this program...but i am not getting the output like you....
Please share your model at ashacademy01@gmail.com
@@TechSimulator thanks for your reply...i sent the pgm to your mail
Thank you so much...can u explain designing sliding mode control for this statcom...your way of showing the program is easy to follow that's why i am asking you....if u don't mind plz explain....
@@meandmycraftideas1499 hello I would like to know if you have fixed the issue because because my system is also not working properly .
@@josuekayembe6129 he sent the model to my mail. That model worked..
thanks sir
🙏🏻
Why my output is not coming
Can u provide the ref paper for this work
Did u got reference paper of this work?
Bro need statcom with fuzzy controller
Why 2/Vdc ?!
Statcom and sssc with fuzzy controller
Will try
@@TechSimulatorwaiting for it sir
Sir can you send me those simulation model file ???
sir please send model in comment
Output is different
Sssc facts controller
Will try
Dear sir, could you please provide your email, i have some query.
ashacademy01@gmail.com
kindly sir need your help share email now
ashacademy01@gmail.com
Why 2/Vdc ?!