Thanks for the Amazing video . I have followed your video and trying to make the TBS nano receiver for PWM output to fly planes . I am not receving the option tracer nano RX under the Crossfire settings , done the firmware update too no go , could you please help ?
Nice job. FYI : when you see in the transmitter [ENTER] [RTN] ! that's mean the system or software is asking you for confirmation by ENTER or return from what ever is going to happened by RTN. You don't have to press them both Thanks again
Can you connect unify pro32 HV to this Receiver? I am converting my Arrma Felony RC Car for Long Range Street Rips. I also want to install betaflight to my RC Car so i can get RSSI, GPS, Buzzer, more channels, LEDs... the works. so for me this is a great video!
I have no experience with the Unify VTX’s but I know you can reallocate the pins of the Nano receiver but I have not done it yet myself. I would not want to give you advice on something I have not yet tried. I am sure it is possible.
If you are asking about your radio I would suggest using channel 5 Mixings Options: Mix Name Arm Source - switch you wish to use for arming. Weight could be -100 or 100 - test in Betaflight before flying your drone. Offset 0 Curve 0
Hey Bill, is there a way to get VBAT sensing using the Crossfire nano RX 6ch adapter? I'm trying to get battery voltage info without a flight controller on my airplane. Any advise would be greatly appreciated.
Not that I am aware of, VBAT comes from the ESC via the FC to the receiver. You will notice that you have only 10 telemetry sensors when the TBS Nano is connected to a PWM adapter.
How do the aileron servos move in opposite directions without channel mixing? As far as i understand the servos should move in the same direction as it is connected to the same channel.
It depends on the orientation of the servos in the model so you may need to reverse the mixes. Basically is the servo are on the left or right side of the servo.
Hi Bill, great video, although I am struggling greatly on my side, would you be able to help me, I can't seem to find decent explanations anywhere aha... So I have a tango 2 and the crossfire 6ch pwm nano rx being set up in a DLG, I bound the rx through agent lite, however, can not seem to get my servos to be working, and I'm now in a muddle with the setup or what settings I should be using... I see you selected crossfire, but if I change any of the modes it un binds it self and doesn't allow me to find it... Please help! Aha 😁
You need to check the Output Map. And check Output 1 = CH1, Output 2 = CH2 and so on in Output Map settings of the Nano receiver using TBS Agent Lite Lua script. Channel Map must be the same CH1 etc. Please check this first.
@@the-happy-RC-flyer Hi Bill, great help thanks, I found the page and made the change so that is now correct but still no joy... I realised that you change the mode in the setup menu to crsf. When I do this I'm unable to bind the rx through agent lite, it will search but not find any options... I've also since tested the servos to check they are still working etc...
@@the-happy-RC-flyer Thank you... trying to use this with the pro32 but not sure exactly how to get it to work without a flight controller in a fixed wing application.
Great video. I have been trying to find this info about the outputs. I'm assuming I can just direct solder servos to save buying the adaptor thing? Provided I get the ground and 5v rail correct?
@@MrEidroeg are you using a Nano or PWM Nano receiver? I am interested how you soldered servos to a Nano receiver without the adapter could you email pictures to me please? triplemadventures@gmail.com.
@@the-happy-RC-flyer Thank you very much for considering me 🤩 I am using Radiomaster Tx16s. I am able to see the throttle movements in my radio all servos are working. But the ESC just made a beep beep sound and not settling, I tried a different ESC motor, and it's the same. Before also followed your video and successfully converted using a 4ch adapter, this time it's a 6ch adapter and stuck with the throttle issue. Not sure what is the problem.
Sorry I do not have a TBS Mambo to check this out but if you want to adjust the output map you need to access the RX once bound to your radio. You should have the Agent Lite lua/app on your radio to access the RX.
Hi there bill. Great video. I have a question regarding setting this up. I use tbs agent lite on my Reciever which is a taranis qx7. When I go into the channels or outputs screen nothing loads. Its just a blank screen. Any idea why this could be happening?
@@MrXSwiiZ Can you access the General and About options in the XF Micro TX? If this persists I would suggest updating the firmware if you have not already done so then if that does not solve the problem Factory Reset the RX via the TBS Agent Lite. I have so far not come across this problem, your RX data is not being sent back to your radio.
Yeah I can access all the other menus just not the output or channel menu. However, when connected to the tbs agent on the laptop I can access these menus. I think a full factory reset is in order
I have never used Crossfire or Tracer with a FrSky QX7 but I think you need to complete a modification for it to work. Please check the internet for the modification the part required is included with the modules.
I live you I have been trying to make the radio works for months until I stumbled in this video, thanks, really 🎉🎉🎉
Awesome video! I couldnt for the life of my figure out why my servos were going crazy, but now I know, thanks!
thanks bill great video your 1st to show how to do with plane. wiil be useing tracer micro in a wing and useing sbus/as useing zohd kopliot.
Thanks Bill, big help. Solved an aching problem here!
I found your channel while looking for info on the Cheetah Glider. Enjoying the content here. Thanks Bill and congrats on passing 600 subscribers.
Thanks for the Amazing video . I have followed your video and trying to make the TBS nano receiver for PWM output to fly planes . I am not receving the option tracer nano RX under the Crossfire settings , done the firmware update too no go , could you please help ?
Do you have the latest lua script for Crossfire on your radio?
@@the-happy-RC-flyer How can I check whether the available one is latest? if not where can I download and how can I install it?
@@waseemzerof4577 go to this website page and Sign Up so you can update your firmware.
www.team-blacksheep.com/agentm/
Nice job.
FYI : when you see in the transmitter [ENTER] [RTN] !
that's mean the system or software is asking you for confirmation by ENTER or return from what ever is going to happened by RTN.
You don't have to press them both
Thanks again
Thanks Bill! Your great.
Hello im a big fan of yours. please start making video tutorials on tango 2. specially for wibg setups
Fahim I would love to make a tutorial series of videos for the Tango I will contact Trappy and see if they will send me one.
Hi there I was wondering if Can I plug in directly the hobbywing 2-1 motor to the TBS crossfire 6ch PWM receiver?
If the motors ESC BEC delivers the correct voltage you should be fine.
By the way can i solder my quad crossfire receiver to PWM adapter that tbs sells or it will be different?
Just check the pin outs are correct.
Is there anyway to get battery voltage from this adapter? I am planning to use it on plane without FC.
Not that I am aware of.
Hello. Do you think this will be good for an edf jet?. Wanna do some fpv flying too
Yes this would be a good choice.
Yes this would be a good choice.
Can you connect unify pro32 HV to this Receiver? I am converting my Arrma Felony RC Car for Long Range Street Rips. I also want to install betaflight to my RC Car so i can get RSSI, GPS, Buzzer, more channels, LEDs... the works. so for me this is a great video!
I have no experience with the Unify VTX’s but I know you can reallocate the pins of the Nano receiver but I have not done it yet myself. I would not want to give you advice on something I have not yet tried. I am sure it is possible.
Where can I find info on setting up the arm switch?
If you are asking about your radio I would suggest using channel 5
Mixings Options:
Mix Name Arm
Source - switch you wish to use for arming.
Weight could be -100 or 100 - test in Betaflight before flying your drone.
Offset 0
Curve 0
Hey Bill, is there a way to get VBAT sensing using the Crossfire nano RX 6ch adapter? I'm trying to get battery voltage info without a flight controller on my airplane. Any advise would be greatly appreciated.
Not that I am aware of, VBAT comes from the ESC via the FC to the receiver. You will notice that you have only 10 telemetry sensors when the TBS Nano is connected to a PWM adapter.
How do the aileron servos move in opposite directions without channel mixing? As far as i understand the servos should move in the same direction as it is connected to the same channel.
It depends on the orientation of the servos in the model so you may need to reverse the mixes. Basically is the servo are on the left or right side of the servo.
@@the-happy-RC-flyer ohh got it now. Thanks for explaining
Hi Bill, great video, although I am struggling greatly on my side, would you be able to help me, I can't seem to find decent explanations anywhere aha...
So I have a tango 2 and the crossfire 6ch pwm nano rx being set up in a DLG, I bound the rx through agent lite, however, can not seem to get my servos to be working, and I'm now in a muddle with the setup or what settings I should be using... I see you selected crossfire, but if I change any of the modes it un binds it self and doesn't allow me to find it...
Please help! Aha 😁
You need to check the Output Map. And check Output 1 = CH1, Output 2 = CH2 and so on in Output Map settings of the Nano receiver using TBS Agent Lite Lua script. Channel Map must be the same CH1 etc. Please check this first.
@@the-happy-RC-flyer Hi Bill, great help thanks, I found the page and made the change so that is now correct but still no joy...
I realised that you change the mode in the setup menu to crsf. When I do this I'm unable to bind the rx through agent lite, it will search but not find any options...
I've also since tested the servos to check they are still working etc...
@@RIPnDIPfpv I would now suggest running the binding process again. Are you able to search for telemetry in the model setup?
can you show how to use this with the tbs pro32 with smart audio as a fpv set up? Thank you for your work!
I do not have aTBS Unify Pro32 but when I get one I will make the video.
@@the-happy-RC-flyer Thank you... trying to use this with the pro32 but not sure exactly how to get it to work without a flight controller in a fixed wing application.
Great video. I have been trying to find this info about the outputs. I'm assuming I can just direct solder servos to save buying the adaptor thing? Provided I get the ground and 5v rail correct?
I think you will need to get hold of the adapter to convert the Nano to PWM.
@@the-happy-RC-flyer ohh right. so there is some kind of conversion going on? doesn't it output pwm out of the 6 holes?
thanks for responding
I have just tested this by soldering some servos to it directly. works fine. thanks again for the video
@@MrEidroeg are you using a Nano or PWM Nano receiver? I am interested how you soldered servos to a Nano receiver without the adapter could you email pictures to me please?
triplemadventures@gmail.com.
@@the-happy-RC-flyer The nano receiver outputs pwm on all 6 pins.
What happens if you need to add expo to the ailerons , how would you do it
You add expo in Inputs.
My throttle is not working for some reason. Can you help me?
Please give me a bit more information so I can try and assist you. Can you see the throttle movement in your radio. Which radio do you have?
@@the-happy-RC-flyer Thank you very much for considering me 🤩 I am using Radiomaster Tx16s. I am able to see the throttle movements in my radio all servos are working. But the ESC just made a beep beep sound and not settling, I tried a different ESC motor, and it's the same.
Before also followed your video and successfully converted using a 4ch adapter, this time it's a 6ch adapter and stuck with the throttle issue. Not sure what is the problem.
@@ASAN is your throttle channel reversed?
Can you help me why my, , tbs mambo ethix tracer nothing to tracer nano rx , , just mambo tracer , , so i cannot to move output map , , thanks before
Sorry I do not have a TBS Mambo to check this out but if you want to adjust the output map you need to access the RX once bound to your radio. You should have the Agent Lite lua/app on your radio to access the RX.
Hi there bill. Great video. I have a question regarding setting this up. I use tbs agent lite on my Reciever which is a taranis qx7. When I go into the channels or outputs screen nothing loads. Its just a blank screen. Any idea why this could be happening?
Sorry silly question is your receiver bound and connected to the Crossfire or Tracer module?
@@the-happy-RC-flyer not silly at all! A mistake I've made before! Yes it's bound and showing in the tbis agent lite program
@@MrXSwiiZ Can you access the General and About options in the XF Micro TX? If this persists I would suggest updating the firmware if you have not already done so then if that does not solve the problem Factory Reset the RX via the TBS Agent Lite. I have so far not come across this problem, your RX data is not being sent back to your radio.
Yeah I can access all the other menus just not the output or channel menu. However, when connected to the tbs agent on the laptop I can access these menus. I think a full factory reset is in order
@@MrXSwiiZ Let me know how it goes please.
Is this new receiver 2.5 or 900?
It is the same for both Tracer & the Crossfire Nano PWM receivers.
Como podria aser eso en un control flysky q7
I have never used Crossfire or Tracer with a FrSky QX7 but I think you need to complete a modification for it to work. Please check the internet for the modification the part required is included with the modules.
What country are you in? Looks like somewhere in Africa.
Hi Pete, I live in South Africa.
@@the-happy-RC-flyer You have a really nice location for flying RC. I am envious.