Big mess up there bud. Should have installed the chain tensioner before turning the engine over to make sure the chain didn't jump teeth while turning the engine over to check for binding.
Ok you probably get this question a lot but can I swap the liquid cooling cylinder for a kymco agility air cooled cylinder and still use it. I'll figure out the rest I just need to know if it fits.
for cooling the oil with an external radiator, this wakes up enough, it is desirable to immediately install the piston 61 or 63 mm, the engine wakes up significantly productive
You see that everybody I didn't see any lubricating oil on the piston rings or the cylinder he put it together dry you can hear the piston rings were very
I believe the point was to demonstrate how it goes together but you would be correct with the lack of oil everywhere however this motor so light you can pour it in the crank case and just turn it all around problem solved
Okay, I need to explain something for you and people like you: THIS IS ONLY SHORT VIDEO OF BUILD THAT ENGINE. In real it's take more time and more than half we cut from this video. All parts was lubricated before installed ! And from next video we safe this on movie special for high level professional commentators like you
Jonathan Crouch oh yeah, so smart! So he driving without gasoline too? On video not have anything how he put gasoline, so what? Come on! Wake up boy! We always without oil and gasoline driving, always!!!! Hahaha!
Yeah I was just about to comment the same thing. Based on the gibberish reply Im not sure they even know WTF they are talking about..BYW,,Where is the Ruckus? XD
I hope not to disturb you in my country this engine is blocked at 50 KM on our road at 90 it is dangerous to drive so low do you have an idea to make it go to 70 80 approximately please I have a sym jet 14 euro 5 injection thank you very much
Ну всё же видно на видео. На коленвале маркировка 125 кубов. Значит двиг будет на 125-150 кубов - 152й или 157й. Они идентичны. 161 же мотор, на 170+ кубов. Там разница в размере картера, разлёте шпилек, увеличенного коленвала ну и скорее всего вариатора (но это не точно) А по поводу тюнинга на 130-140 км/ч и выше, тебе нахер столько? Уничтожиться на китайце? А вообще скорость увеличивается не данным тюнингом, а заменой колеса, передаточным числом редуктора и вариатора. В мощности потеряешь, но скорость повысишь. Только это бесполезная трата денег и времени.
Дорого. Коленвал около 12-15, сцепуха косо в районе 9, варик в сборе 4-6, ЦПГ (жидкостное) даже не в курсе скок стоит, бошка где то 5-8. ну и по мелочи ещё рублей на 5-7. Считай. Но цены просто в среднем взяты из памяти. Там разброс может быть +- 2-3 тысячи.
C est ca les gars apprendre comment tirait des chevaux d un moteur apres c est les meme nous a la fin sur des motobecane on faisait des bie ou trie cylindres et la fallait renforcer le cadre et croyait moi a 140 kmh sur une mob c est le truc le plus dingues que j ai fait ca fait flippé surtout que le moteur tiennent le coup parce que ont parier tout et n importe quoi argent bisou avec ca meuf j ai meme vue un gars parier ca becanes le perdant perder ca becanes et ci il y a des anciens de Vincennes le vendredi soirs dans les années 80 savent que je men pas mais il y avait de tout mon 103 bie cylindres 80 cc realeser cote 3 deux gros carbu a la fin c est mon beau pere qui etait tourneur fraiseur qui me faisait mais piston et donc bien plus costaud que dans le commerce parce dans c est années croyait moi polinie et tout les autres kits qui y avait ce faisait un fric de maladies tout le temps de nouveau kit jusqu'à ce que je trouve le bon un malossie bie cylindres carbu de 21 22 ca depender de la soiree y a des mec il monter des moteurs 125 cc de dtmx qu il render en moteur Mob mais il casser courroie sur courroie combien de fois j ai gagner contre eux parce que avant l arriver courroie casser et moi je passer et gagner argent numero de téléphone avec leur copines le bon temps quoi jusqu a ce que le sida arrive et face fliper mille fois plus que le corona ci tu le faisait sans capotes c etait ta vie que tu jouer enfin bref les années 80 ont etait les meilleurs des pires années et j ai survécu a tout ca meme Tchernobyl l usines cas exploser en 85 86 ou il y a eux des cancer s de partout ont dirait qu ils ont besoins d'envoyer des virus tout les 20 ans
senin yapacağın motor toplamaya giydireyim o krang bilyalarıni ısıtmadan bloğa oturtmaya çalıştın ya baştan sıfırı direk aldın senden motorcu falan olmaz o bilyalar ve blok belli bir ısıda genleşip yerine öyle oturtulmalidir lakin ilk yilinda alırsın rulmanları eline kolay gelsin
@@ahmetakifguner7023 hangi motor olursa olsun içten yanmalı motorlarda rulman yatağı kesinlikle işlem yapılmadan rulman oturtulmaz zira motorun vermiş olduğu belli bir ısı var bunun doğrultusunda rulman yataklarında genişleme olacağı için yaptığı olay yani rulmani direk oturtma işi tamamen yanlış
@@Konniemm obviously its a gy6 not a 49cc honda GET. The title says gy6 for "RUCKUS" but it wasnt on a ruckus in the end of the vid. I simply stated that.
@@AverageJoe84 That’s a Ruckus frame with a GY6 mount installed. They later extended the frame, painted it and what not. It looks pretty damn good. Check it out. ua-cam.com/video/_jL8xTWvu9A/v-deo.html
![GY6 ENGINE BUILD [Everything you need to know]](http://i.ytimg.com/vi/wC5tYKqq0-0/mqdefault.jpg)
![GY6 ENGINE BUILD [Everything you need to know]](/img/tr.png)
Oh my gosh! I just found your website and it is awesome! Amazing parts!
Big mess up there bud. Should have installed the chain tensioner before turning the engine over to make sure the chain didn't jump teeth while turning the engine over to check for binding.
منور استمر تحياتي الك من العراق👍👍👍👍👍👍👍👍
Ok you probably get this question a lot but can I swap the liquid cooling cylinder for a kymco agility air cooled cylinder and still use it. I'll figure out the rest I just need to know if it fits.
for cooling the oil with an external radiator, this wakes up enough, it is desirable to immediately install the piston 61 or 63 mm, the engine wakes up significantly productive
nice camera angle sir
It dont haft to be a ruckus to have a bad ass Gy6 motor Sir
You see that everybody I didn't see any lubricating oil on the piston rings or the cylinder he put it together dry you can hear the piston rings were very
I believe the point was to demonstrate how it goes together but you would be correct with the lack of oil everywhere however this motor so light you can pour it in the crank case and just turn it all around problem solved
I have one but don’t have the right wire harness thing
Hello, does this engine work on a Zoomer bike, and how much does the engine cost with tires and supplies?
Instead of using rubber mallet. The dude in the video prefer to use his hand 🤣🤣🤣
Is it possible to build a 85hp gy6 engine build for drag racing if you could do that can you build me one with reverse for a gy6 trike
No not in a million years. 40 MAX and with boost MAYBE 50 if you're lucky at the crank but it would need to be turning at like 10 or 12,000 RPM's
i love this kind of engine for my fino😍😍🥰🥰 sponsor pls master🙏🙏🙏🙏
Bolts without lubrication, the Bearings are inserted to dry without shrinking , the Chain without lubrication ,,, ))))
Okay, I need to explain something for you and people like you:
THIS IS ONLY SHORT VIDEO OF BUILD THAT ENGINE.
In real it's take more time and more than half we cut from this video. All parts was lubricated before installed ! And from next video we safe this on movie special for high level professional commentators like you
doing a formidable job,if i had the money i would use our service :).
good too see love and craftmanship together .
do you do any tuning?
Крутые запчасти у нас таких не найти Беларусии Минск
А их только на заказ. Если что...
No lube when installing piston into cylinder? Who does that? Nice build, but that hurt to watch.
Jonathan Crouch oh yeah, so smart! So he driving without gasoline too? On video not have anything how he put gasoline, so what? Come on! Wake up boy! We always without oil and gasoline driving, always!!!! Hahaha!
Yeah I was just about to comment the same thing. Based on the gibberish reply Im not sure they even know WTF they are talking about..BYW,,Where is the Ruckus? XD
If anything it all just looked a little nervous and jammy. Didnt see a torque wrench hit a single bolt
I am a brand new subscribed your channel right now is any of these parts are they on your website
You need a lightweight flywheel
Wait was that you cranking it without chain tensioner?
A little finesse and a Torque Rench.
Magkano po yun isang buo makina
Et dire que tous ça vaut le prix d'une belle sportive d'occasion !!! mais je respecte le travail et la beauté des pièces, magnifique !!!
do you want to build one more drive train and i would buy it if it is a long block
Did you have to do any welding for the installation or stretch?
Because I'm thinking about ordering one next month
Awesome 👍👍
Are these sold in parts or are they assembled and then shipped out?
R u sure those bolt for intake manifold is long enuf to hold them?
Does a 4 valve head have more torque and power? (never used it)
I wast 40 min waiting for how he will install the water cooler on gy6.
If I purchased this what else will be needed to mount it to a ruckus? Or is everything included?
Need many parts for install it to ruckus
Да уж сборка оставляет желать лучшего. После каждой паузы мотор становился на разных запчастях 🤣🤣🤣
Hello. Nice ✌️🎙 looking to up grade a 49 cc . Any suggestions 🖐🏼 2009 Mio 50 scooter 🛵 looking for better cooling. ✍️
What brand of carburetor did you use?
Looks like a fairly standard Honda gy6 clone carb tbh
Hello. What jets do you use for this config?
the 125cc Crankshaft is the same 4 150cc?
and bigbore 182cc?
may i use a 125cc in a 150cc engine?
thanks 4 the answers. Presiate.
Juande Dios Salazar you can use yours crankshaft , 125 and 150 is the same ...
@@BWSP-CLUB lot of thanks
Красава🎉🤝👍✊💪👊
I want this engine how much its price?
2 camels
How macho the kit
Precio de ese motor completo?
Beat karbu bore up dohc,,gas mumbul mumbul
Mantep cak,,kirim nek jowo iso tah ora?
@@riezhariezh787 salah server
@@bgsandrywn wkwkwk
chain timing gold
There is no spring at CVT?
The set of 4valve head costs 75$ in china 😋
Someone know if you can get watercooling for 80cc gy6 ?
Yeah you can Taida parts
Bonjour, peut on monte ceci sur des carters de 50cc gy6??
no these are for 125 cc. Wheel hub is bigger, and other oilpump ect.
What is the top speed? 🚴
47kph
wtf thanks your video my from france your motor my motor sym jet 14 euro 5 very very thank you
sorry, i have a bad command of the language
I hope not to disturb you in my country this engine is blocked at 50 KM on our road at 90 it is dangerous to drive so low do you have an idea to make it go to 70 80 approximately please I have a sym jet 14 euro 5 injection thank you very much
So sad the shipping prices KILL every single part they sell.
Where is the water pump located?
,,maybe they use a electric waterpump,
Top job🏁🏆
Top job?? Youre nuts, homie...
какой блог брал 157qmj или 161qmk сними тюнинг на 157qmj и чтобы ехал 130км/ч ии 140 или выше
Ну всё же видно на видео. На коленвале маркировка 125 кубов. Значит двиг будет на 125-150 кубов - 152й или 157й. Они идентичны. 161 же мотор, на 170+ кубов. Там разница в размере картера, разлёте шпилек, увеличенного коленвала ну и скорее всего вариатора (но это не точно)
А по поводу тюнинга на 130-140 км/ч и выше, тебе нахер столько? Уничтожиться на китайце? А вообще скорость увеличивается не данным тюнингом, а заменой колеса, передаточным числом редуктора и вариатора. В мощности потеряешь, но скорость повысишь. Только это бесполезная трата денег и времени.
Ship to Brazil? 😀
Yes
Cuanto cuesta todo ese kit
Is it okay to leave CVT exposed like that?
hell nah. but had to be done because of the oversize clutch
Yes as long as you have a brace for it. offers more cooling
Yea as long as your not running it threw dusty roads gravel mud or rain I have mine off because it no longer fits and don’t feel like cutting it
Whats the purpose?
E io raffreddamento? Pompa/radiatore??
Donde puedo comprar este motor . Tal cual lo tienes ?
Como faço para comprar 🙏🙏🙏🇦🇴
YES NICE WAKOOOOOMMMMM
How much for the exhaust to usa
.... Taiwan GY6?
Hola, y todos esos accesorios dónde se compran
eBay
Bonjour! je voudrai savoir pour le prix de qit complet du moteur
Where can I find shipping cost (Hawaii)?
Add my WhatsApp +8613068844900
How much 4valve cylender heads
Nicht ohne Seitendeckel ! :-)
take out that db killer for the love of god please
สุดยอดเลย🤩🤩🤩🤩🤩
the fuel filter isnt sat corectly
that's NOT!!! how do you put a bearing case onto a bearing? not now, and never!! time to go to mechanic school for sure!!!
I think this guy hates his job.
Artinya apa lek ?
Looks like amatir,,,
Сколько стоит такой мотор?
Дорого. Коленвал около 12-15, сцепуха косо в районе 9, варик в сборе 4-6, ЦПГ (жидкостное) даже не в курсе скок стоит, бошка где то 5-8. ну и по мелочи ещё рублей на 5-7. Считай. Но цены просто в среднем взяты из памяти. Там разброс может быть +- 2-3 тысячи.
@@leatherandsilver350
😱Понял. Дешевле взять авто с салона🤪
@@leatherandsilver350 дорого это сколько???
@@Villi-hv3uk а внимательно прочесть религия не позволяет? Вроде все расписал
@@leatherandsilver350 прошу прощения это доллары или рубли?)
Fabuleux 👌🤪🤪🤪
Sounded like it hit the valves
А помпа где
Ship to Mexico?
Yes
Le mieux c est les 2 temps pas costaud mais ca pousse severe
C est ca les gars apprendre comment tirait des chevaux d un moteur apres c est les meme nous a la fin sur des motobecane on faisait des bie ou trie cylindres et la fallait renforcer le cadre et croyait moi a 140 kmh sur une mob c est le truc le plus dingues que j ai fait ca fait flippé surtout que le moteur tiennent le coup parce que ont parier tout et n importe quoi argent bisou avec ca meuf j ai meme vue un gars parier ca becanes le perdant perder ca becanes et ci il y a des anciens de Vincennes le vendredi soirs dans les années 80 savent que je men pas mais il y avait de tout mon 103 bie cylindres 80 cc realeser cote 3 deux gros carbu a la fin c est mon beau pere qui etait tourneur fraiseur qui me faisait mais piston et donc bien plus costaud que dans le commerce parce dans c est années croyait moi polinie et tout les autres kits qui y avait ce faisait un fric de maladies tout le temps de nouveau kit jusqu'à ce que je trouve le bon un malossie bie cylindres carbu de 21 22 ca depender de la soiree y a des mec il monter des moteurs 125 cc de dtmx qu il render en moteur Mob mais il casser courroie sur courroie combien de fois j ai gagner contre eux parce que avant l arriver courroie casser et moi je passer et gagner argent numero de téléphone avec leur copines le bon temps quoi jusqu a ce que le sida arrive et face fliper mille fois plus que le corona ci tu le faisait sans capotes c etait ta vie que tu jouer enfin bref les années 80 ont etait les meilleurs des pires années et j ai survécu a tout ca meme Tchernobyl l usines cas exploser en 85 86 ou il y a eux des cancer s de partout ont dirait qu ils ont besoins d'envoyer des virus tout les 20 ans
140 en mob.. hahahaha... si c'était si simple. Pourquoi à l'époque un loustique a usiné un carter avec distributeur rotatif...
👍👍👍👍
😍😍😍😍😍
How to buy for QMJ engine
How much this
senin yapacağın motor toplamaya giydireyim o krang bilyalarıni ısıtmadan bloğa oturtmaya çalıştın ya baştan sıfırı direk aldın senden motorcu falan olmaz
o bilyalar ve blok belli bir ısıda genleşip yerine öyle oturtulmalidir lakin ilk yilinda alırsın rulmanları eline kolay gelsin
2 zamanlıda yapıyordu ama bu motorda ısıtmadan taktı bi bildiği vardır belki
@@ahmetakifguner7023 hangi motor olursa olsun içten yanmalı motorlarda rulman yatağı kesinlikle işlem yapılmadan rulman oturtulmaz zira motorun vermiş olduğu belli bir ısı var bunun doğrultusunda rulman yataklarında genişleme olacağı için yaptığı olay yani rulmani direk oturtma işi tamamen yanlış
I personally do not like that Computer fan.... I feel like that Radiator and Fan are really not good enough.
saludos desde colombia donde puedo comprar partes gy6 190 cc con radiator
I have 200cc
👍
titanium bolts
Ca tient ou ca casse faciles boys please
Bingung sih
Cuando lo armes lubrica todo antes de armar
I guarantee you my two valve cylinder head I can compete with that for valve cylinder head it all depends what you know what you can do
Can't see half the stuff he's doing!
Horsepower?
4
@@Prxpagandalf you mhoter in 4 jajaj
pliz video scooter 50cc to 125cc conversion
Not possible
All that and uses egr valve cover and a pod filter. That isnt a ruckus either....😢
What’s wrong with a pod filter?
Man this isn’t a stock Ruckus motor. It’s intended to be swapped onto a Ruckus. Pretty much the bikes main purpose in the communities surrounding it.
Pod filters suck. Foam is much better.
@@Konniemm obviously its a gy6 not a 49cc honda GET. The title says gy6 for "RUCKUS" but it wasnt on a ruckus in the end of the vid. I simply stated that.
@@AverageJoe84 That’s a Ruckus frame with a GY6 mount installed. They later extended the frame, painted it and what not. It looks pretty damn good. Check it out. ua-cam.com/video/_jL8xTWvu9A/v-deo.html
Preciso de um Motor desses.Quanto custa?
3.500 + 1.800 de frete e 60% de imposto de importação e 32 de ICMS
Собрано похабненько!
Amatiiiiiir.....!!!!!
и что в нем такого кроме внешнего вида? не даст он мощности больше чем в нем есть.
Yeah, don’t worry about checking the ring gap on an engine build. Lol
Me either. Hasn't become an issue yet
Mekanik e rung ngopi