0:00:00 Remove the face plate and top cover 0:00:02 Remove the stop motion wheel and hand wheel 0:00:30 Loosen the feed regulator lever screw 0:00:32 Remove the handwheel bush and toplon washer 0:00:56 Unscrew and remove the dish track (dish holder). 0:01:37 Unscrew and remove the feed regulator 0:02:37 Unscrew and remove the gear wheel 0:02:39 Loosen the Ascentic pedaling wheel screws 0:02:59 Loosen the main shaft wheel screw 0:03:11 Unscrew and remove the vibrating ascentic shaft and vibrating bracket 0:03:32 It will be convenient for you to remember the location of the two cut marks on the upper end of the vibrating bracket ascentic shaft. 0:03:38 Unscrew and remove the vibrating bracket and the Asentic shaft 0:04:28 Unscrew and remove the needle bar 0:04:33 Unscrew and remove the threadtakeup lever 0:05:25 Loosen the bevel gear screws and the eccentric bearing screws 0:05:30 Pull out the main shaft and remove the broken bevel gear. 0:05:53 Insert the new main shaft wheel into the machine. 0:05:55 Reinstall all previously removed parts as they were before. 0:07:57 Reinstall all previously removed parts as they were before. 0:08:18 Rotate the main shaft so that the threaded take-up lever mounting screws are facing up. 0:08:28 Tighten the bevel gear pin into the cut mark parallel to the threaded take-up lever mounting screw. 0:08:38 Install the eccentric bearing screw on the cut mark opposite the cut mark where the bevel gear screw is installed. 0:08:48 If the two screws on the bevel gear and the eccentric bearing are installed incorrectly, the fabric will be pushed backwards instead of forwards. 0:08:58 Install DishTack now. 0:09:00 Now install the feed regulator. 0:09:30 If you have any further questions, please watch the videos uploaded regarding this repair and this sewing machine. 0:09:40 Install the thread take-up lever and needle bar and vibrating bucket. 0:09:45 Watch the uploaded videos on needle bar timing and needle bar position adjustment. 0:11:45 Thank you for watching the video, please subscribe to the channel.
0:00:00
Remove the face plate and top cover
0:00:02
Remove the stop motion wheel and hand wheel
0:00:30
Loosen the feed regulator lever screw
0:00:32
Remove the handwheel bush and toplon washer
0:00:56
Unscrew and remove the dish track (dish holder).
0:01:37
Unscrew and remove the feed regulator
0:02:37
Unscrew and remove the gear wheel
0:02:39
Loosen the Ascentic pedaling wheel screws
0:02:59
Loosen the main shaft wheel screw
0:03:11
Unscrew and remove the vibrating ascentic shaft and vibrating bracket
0:03:32
It will be convenient for you to remember the location of the two cut marks on the upper end of the vibrating bracket ascentic shaft.
0:03:38
Unscrew and remove the vibrating bracket and the Asentic shaft
0:04:28
Unscrew and remove the needle bar
0:04:33
Unscrew and remove the threadtakeup lever
0:05:25
Loosen the bevel gear screws and the eccentric bearing screws
0:05:30
Pull out the main shaft and remove the broken bevel gear.
0:05:53
Insert the new main shaft wheel into the machine.
0:05:55
Reinstall all previously removed parts as they were before.
0:07:57
Reinstall all previously removed parts as they were before.
0:08:18
Rotate the main shaft so that the threaded take-up lever mounting screws are facing up.
0:08:28
Tighten the bevel gear pin into the cut mark parallel to the threaded take-up lever mounting screw.
0:08:38
Install the eccentric bearing screw on the cut mark opposite the cut mark where the bevel gear screw is installed.
0:08:48
If the two screws on the bevel gear and the eccentric bearing are installed incorrectly, the fabric will be pushed backwards instead of forwards.
0:08:58
Install DishTack now.
0:09:00
Now install the feed regulator.
0:09:30
If you have any further questions, please watch the videos uploaded regarding this repair and this sewing machine.
0:09:40
Install the thread take-up lever and needle bar and vibrating bucket.
0:09:45
Watch the uploaded videos on needle bar timing and needle bar position adjustment.
0:11:45
Thank you for watching the video, please subscribe to the channel.
Where is your repair shop.
I need to repair the same machine.
Interesting but no way possible for me.