hi, I did the same swap on my 2002 tj, with a 1999 engine. I kept my 2.5 harness frame but currently I have an ignition problem, what are the exact modifications you did you do on the harness please?
Did you change ECU from your 2.5 to an ECU for a 4.0? did you use your 2.5 wiring harness? where can i get a copy of the wiring change that in your video. i am in the process of removing 2.5 and installing MORE motor mount kit i purchased. just need help on figuring out the wiring. thanks james
Apologies for the late reply. Need to figure out how to get notifications on this thing. Let me know if you still need info. To answer your questions: 1.) I got my 2.5 ECU reprogrammed from this company called ARES technologies in Reiverside, CA. 2.) I actually ended up using a wiring harness from a 99 but required some mods to connectors. More trouble than it's worth, but it was the only wiring harness I could find for the inline 6. Good luck, if you haven't already finished the swap.
Not sure how far along you are in the process, but there's quite a few things you would need to change i.e. Motor mount location, transmission, transfer case (or spline swap).
![[UA] NAVI vs MOUZ | BO5 | IEM Rio 2024](http://i.ytimg.com/vi/CMBYk0cbGoA/mqdefault.jpg)
The yj I just bought came with a swapped 4.0 but the harness still needs to be repaired and having a lot of backlash help!
Where do you see the backlash?
Awesome!! I want to do this! Can you possibly make a video explaining the wiring a little more ? I love my tj but I need more power for sure.
Nice job
What did this job cost you out the door if you don’t mind me asking ? I just blew my 2.5 and have to replace the motor 🤦♂️ .
Nice Video
Hello, I made the same modifications as you, but my car starts for 5 seconds and then stops.
Where you programmed 2.5 ECU 4.0L 🙏
hi, I did the same swap on my 2002 tj, with a 1999 engine. I kept my 2.5 harness frame but currently I have an ignition problem, what are the exact modifications you did you do on the harness please?
you obviously did get a new harness for the 4.0 and new trans, correct? can you elaborate on the problem? does it crank but no start? no power at all?
Did you change ECU from your 2.5 to an ECU for a 4.0? did you use your 2.5 wiring harness? where can i get a copy of the wiring change that in your video. i am in the process of removing 2.5 and installing MORE motor mount kit i purchased. just need help on figuring out the wiring.
thanks
james
Apologies for the late reply. Need to figure out how to get notifications on this thing. Let me know if you still need info. To answer your questions: 1.) I got my 2.5 ECU reprogrammed from this company called ARES technologies in Reiverside, CA. 2.) I actually ended up using a wiring harness from a 99 but required some mods to connectors. More trouble than it's worth, but it was the only wiring harness I could find for the inline 6. Good luck, if you haven't already finished the swap.
I want to do this to my 2.4
I have a 2001 jeep it was 2.5 but I changed the engine to 4.0 but it only changes the engine harnes and the e cm or it has to be everything help
Not sure how far along you are in the process, but there's quite a few things you would need to change i.e. Motor mount location, transmission, transfer case (or spline swap).
where you got the brackets that you welded to the frame ? thx
From M.O.R.E Mountain Offroad @Mountainoffroad
Amazon also got it