I purchased these directly from Noble and installed these today. Please please please do not use a pry bar or a flathead screwdriver to remove the stock reflectors. I left several deep gouges that I could catch with my fingernail in the surrounding plastic after the screwdriver slipped and scraped the bumper. Rather, crawl underneath from under the center of the bumper, and look up towards the reflector. You should be able to see the clips holding the reflector in place. You can fish your arm up and pop out the clips with no damage to the plastic.
THANK YOU, THANK YOU, THANK YOU. This is a HUGE help and not only saves your OEM deflectors but makes the install so much easier. The Noble Reflectors should be pre-crimped, which would also save time, but they go look and function great and are worth it imo.
I had these on for a couple months, Installed them with your wiring harness that's plug and play. Now the left one burned out due to a defective LED. But as usual IIR comes through and is sending out a new set so we can get these back to the manufacturer to see what caused the defect for future product.
DO NOT USE A SCREWDRIVER OR PRY TOOL LIKE IN THIS VIDEO! IT PERMANENTLY MARRED THE PLASTIC AROUND IT! Reach for the clips from behind. Your hand will reach. Still upset this ruined my bumper 😭 Would have to order a whole new bumper to fix it. And I'd have to get it ceramic coated again. Time and money 😢
Installed the clear set yesterday, I’m pretty happy with them but they aren’t a perfect fit. If you’re super picky you may want to modify the holes just a little. They may sit in the area more flush. The wires sure seem pinched also. I have not tried this yet. The CLEAR SET does not have the C style light pattern. Instead it’s individual lights, you can see light pattern in the webpage but an on the car example should have been included in this video because it is different enough. Also I had to remove my bumper to install a ecohitch so removing the reflectors was super easy from behind. But I only mention this because I was able to see the light kit installed from behind. Although I pushed through in the lights into the holes quite hard I still had to get a small screwdriver to pull clips farther through to be completely locked in. Hopefully this can be done from under the car with bumper remaining on car. I DO NOT RECOMMEND TAKING OF REAR BUMPER UNLESS YOU NEED TO FOR ANOTHER PROJECT. I did a harness on each side, super easy but it is a bit more to tuck away behind lights. I found tucking them down was the best to fit taillights back to proper spot easily. I have a silver WRX and just didn’t like the red reflector on the silver cars for some reason. The bumper is a bunch of black and didn’t want to black it out creating more black but I do appreciate the clean look of the black ones. The clear lenses look good on the silver cars in my opinion. Hopes are that they will be sufficient enough light and I can black out taillights in clear lenses area.
I only want to use these for parking/brake lights. I would be getting the F1 light as well. I would only need 1 Noble harness since I'm not using signals?
@@dradammichael you can reach the back side of both rear reflectors from underneath the rear of the bumper. Once you drop a line from the tail light to the first corner light, another pig tail can be ran across the inside of the bumper to reach the second reflector.
Thanks, @@BuckleUpGarage_ I ended up ordering an F1 and 2nd harness (always planned on it but figured might as well do it now). Appreciate the info and your videos are super helpful and enjoyable. Thanks again!
Stupid question, but what if you have the side marker lights too, I want these and those as well, I also already have an F1 light would they allow for connection of all three?
My reflectors came with a yellow wire instead of a white so i assumed its the parking and put the red for turn as well but any reason why the turn doesnt work with the lights on? It works if I have all the lights off it looks like its as bright as the parking light so it doesnt show it blinking , it does the same situation for the brake light too lights off work
Installed these exactly the way you did, does the blinker only work when the lights are off?? Mine don’t activate if I have my lights on but if they’re off the blinker works.
@@Dec31st double check your 2 positive wires aren't hooked up opposite, it sounds like you make have the blinker hooked up to the dimmer light and the tail light hooked to the brighter. This will cause the issue you are having.
I purchased these directly from Noble and installed these today. Please please please do not use a pry bar or a flathead screwdriver to remove the stock reflectors. I left several deep gouges that I could catch with my fingernail in the surrounding plastic after the screwdriver slipped and scraped the bumper. Rather, crawl underneath from under the center of the bumper, and look up towards the reflector. You should be able to see the clips holding the reflector in place. You can fish your arm up and pop out the clips with no damage to the plastic.
THANK YOU, THANK YOU, THANK YOU. This is a HUGE help and not only saves your OEM deflectors but makes the install so much easier. The Noble Reflectors should be pre-crimped, which would also save time, but they go look and function great and are worth it imo.
F*ck ust did this and was gonna leave the same comment
Gouges look horrible
Was just told I can use a heat gun to fix it. Will need to keep the heat gun at a distance. And keep it moving, instead of keeping it in one spot.
I had these on for a couple months, Installed them with your wiring harness that's plug and play. Now the left one burned out due to a defective LED. But as usual IIR comes through and is sending out a new set so we can get these back to the manufacturer to see what caused the defect for future product.
DO NOT USE A SCREWDRIVER OR PRY TOOL LIKE IN THIS VIDEO! IT PERMANENTLY MARRED THE PLASTIC AROUND IT! Reach for the clips from behind. Your hand will reach. Still upset this ruined my bumper 😭 Would have to order a whole new bumper to fix it. And I'd have to get it ceramic coated again. Time and money 😢
Waiting for this video long ago, thanks uncle Jim 🥳
Any time good buddy! Now go make ol’ unky Jim proud 🥹
Me too
Nice! Bought mine and thought making a video how to install them since there was none! Thanks and great product!
Installed the clear set yesterday, I’m pretty happy with them but they aren’t a perfect fit. If you’re super picky you may want to modify the holes just a little. They may sit in the area more flush. The wires sure seem pinched also. I have not tried this yet.
The CLEAR SET does not have the C style light pattern. Instead it’s individual lights, you can see light pattern in the webpage but an on the car example should have been included in this video because it is different enough.
Also I had to remove my bumper to install a ecohitch so removing the reflectors was super easy from behind. But I only mention this because I was able to see the light kit installed from behind. Although I pushed through in the lights into the holes quite hard I still had to get a small screwdriver to pull clips farther through to be completely locked in. Hopefully this can be done from under the car with bumper remaining on car. I DO NOT RECOMMEND TAKING OF REAR BUMPER UNLESS YOU NEED TO FOR ANOTHER PROJECT.
I did a harness on each side, super easy but it is a bit more to tuck away behind lights. I found tucking them down was the best to fit taillights back to proper spot easily.
I have a silver WRX and just didn’t like the red reflector on the silver cars for some reason. The bumper is a bunch of black and didn’t want to black it out creating more black but I do appreciate the clean look of the black ones. The clear lenses look good on the silver cars in my opinion. Hopes are that they will be sufficient enough light and I can black out taillights in clear lenses area.
I only want to use these for parking/brake lights. I would be getting the F1 light as well. I would only need 1 Noble harness since I'm not using signals?
Yes if you run both sides to the same tail, but it's a shorter run going straight up to their respective side.
@@ImportImageRacing what’s the best method to pull the cable to the other side when using 1 harness, and I presume I use the included posi-taps?
@@dradammichael you can reach the back side of both rear reflectors from underneath the rear of the bumper. Once you drop a line from the tail light to the first corner light, another pig tail can be ran across the inside of the bumper to reach the second reflector.
Thanks, @@BuckleUpGarage_
I ended up ordering an F1 and 2nd harness (always planned on it but figured might as well do it now). Appreciate the info and your videos are super helpful and enjoyable. Thanks again!
@@dradammichael no problem! 🤘🏻🤘🏻Always here to help!
Do you need to bridge both sides to do this? They only mention one aaid and acr like your done???
I need the harness link pls…
I’ve got the rear lights already but they don’t come with the harness
🇦🇺
Subaru Impreza 2017
Email Support@importimageracing.com! They can get you what you need 🤘🏻
That’s nice. 👍
Stupid question, but what if you have the side marker lights too, I want these and those as well, I also already have an F1 light would they allow for connection of all three?
Yes, the PnP harness allows for multiple lights to be used together! 🤘🏼
Would these fit a 2011 WRX hatchback, seems like they have the same size reflector? I’m fine with having to make adjustments to the wiring
They actually will :)
I have a 3rd brake like with a plug and play harness already, does use the existing plug or do I have to decide which one I want to use
buy the 2nd noble harness, its why most buy 2 one for the f1 and another for these
Super simply!
Did not fit my 23 wrx 😢
Does this work with the Diode Dynamics tail as turn kit?
yes, as long as they wire the reflector light in BEFORE the DD device, before as in on the vehicle side of the DD device not the tail light side
whats the carbon piece on the trunk lid? hope its for sale soon
Going quick! www.importimageracing.com/products/noble-carbon-fiber-license-plate-panel-subaru-wrx-2022-2023?_pos=1&_sid=a6f02a334&_ss=r
My reflectors came with a yellow wire instead of a white so i assumed its the parking and put the red for turn as well but any reason why the turn doesnt work with the lights on? It works if I have all the lights off it looks like its as bright as the parking light so it doesnt show it blinking , it does the same situation for the brake light too lights off work
Mine does absolutely the same thing. It can be a parking light or a blinker but not both. I’ve tried every which way. My wires yellow also. Not white.
Same problem bro, I saw another video and dude says to put the red on parking and yellow for the turn
What did you guys do to solve this? I have the same issue. I can't have both. I recieved the yellow wire as well vs white
you guys are more professional than this. right tools for the job. c'mon man (in the voice of Chris Berman/ESPN)
Purchased but when I installed they did not turn on ?
Email Support@importimageracing and they can get you taken care of swiftly!
Just purchased the reflector kit :) would you recommend getting this also ?
The wiring harness? heck yes! going to do the f1 at the same time, get 2 of them.
@@ImportImageRacing got two of them! I appreciate you and everything you do!
@@JustisFlame Thank you for the support! We will continue making new products and videos! Thank you!
Bridge extension necessary if i have the PNP harnes (1)? If so why dont thye mention it in the video?
does the harness come in with 2 or just 1? I only ordered one and the description didnt say if its 2 or 1
Just one
How long is the rear reflector cable?
Does the harnesses on the website sell as a pair or in singles
It is sold each, so you may want 2
Does this light have strobe brake mode also?
No it does not.
@@derekgingerich thanks
Still waiting on the dual exit exhaust
same, im getting old!
Installed these exactly the way you did, does the blinker only work when the lights are off?? Mine don’t activate if I have my lights on but if they’re off the blinker works.
Well this is interesting. I’m going to check mine. I never checked with the lights on only with the lights off.
@@MLH0214 pls get back to me lol
@@Dec31st double check your 2 positive wires aren't hooked up opposite, it sounds like you make have the blinker hooked up to the dimmer light and the tail light hooked to the brighter. This will cause the issue you are having.
@@derekgingerich so besides the ground, swap out the other 2 connectors?
@@Dec31st exactly!