They sell different length injection lines for the bench, as to have them all the same length! Had to bend them a little to match on the v- style pumps! Also took a spring and old valve that hooks on rack to keep the rack under pressure against the pin, makes it a lot easier to put the barrel and plungers in! Also if doing a complete rebuild take a maker to the center tooth so it is easy to see when looking down at the rack that it is centered with the line up pin on the cam follower! They also make a tool to help push down on the barrel and plunger to get the nut started! Also took and old top of barrel and plunger threaded put and braze it to and old nut to get the first barrel and plunger pushed down start that nut and tighten it, then use it to help get the rest push down!
The one with the longer Injector line is actually not longer. All mechanical fuel injection lines are actually the same length. Especially on this 3406b. The closer cylinders will have the line coiled.
I changed one of the o rings on top of the plunger that was leaking. The next day another one started to leak so I went to caterpillar and got all of them and replace them. A week later my diesel started mixing with oil. One of the plungers popped up while I was changing the o ring it was pretty dirty. I wonder should I change the timing spacers. It had me down 2 weeks trying to figure it out. Any help would greatly be appreciated. Thanks
Might have a lifter went down. Pull the cover off the side (two bolts) and see if the rack will move. I would have a plate to put over the intake just in case it runs away.
@@glencarlisle7710 I would send it out, you have to pin the pump, remove the fuel shut off solenoid so you can slide the rack back, then there is a special tool used to set the individual pumps in. It’s been so long since I done it I would probably mess it up, and you can mess it up and the pump stick to full throttle lol
They sell different length injection lines for the bench, as to have them all the same length! Had to bend them a little to match on the v- style pumps! Also took a spring and old valve that hooks on rack to keep the rack under pressure against the pin, makes it a lot easier to put the barrel and plungers in! Also if doing a complete rebuild take a maker to the center tooth so it is easy to see when looking down at the rack that it is centered with the line up pin on the cam follower! They also make a tool to help push down on the barrel and plunger to get the nut started! Also took and old top of barrel and plunger threaded put and braze it to and old nut to get the first barrel and plunger pushed down start that nut and tighten it, then use it to help get the rest push down!
I've been looking for help doing first one, this is so great all the advice you said!
going to the club with your fuel pump nice pics
I have really enjoyed your video and I have lent slot.
The one with the longer Injector line is actually not longer. All mechanical fuel injection lines are actually the same length. Especially on this 3406b. The closer cylinders will have the line coiled.
Muy bueno el reportaje. Gracias
I changed one of the o rings on top of the plunger that was leaking. The next day another one started to leak so I went to caterpillar and got all of them and replace them. A week later my diesel started mixing with oil. One of the plungers popped up while I was changing the o ring it was pretty dirty. I wonder should I change the timing spacers. It had me down 2 weeks trying to figure it out. Any help would greatly be appreciated. Thanks
How do you get a true reading off that one pump with the longer injector line?
What to do with a stuck fuel rack?
Might have a lifter went down. Pull the cover off the side (two bolts) and see if the rack will move. I would have a plate to put over the intake just in case it runs away.
Je vais aprendre en ligne cordialement réviser Une pompe d'injection cat et toutes marques
Wish it was a live video with explanations about what's going on
Same!! I have replaced the individual injector pumps (
barrels and plungers) but never tore one all the way down
@@veteransdieselgarage7607 how hard was it I have 3 seeping fuel not sure if I’m smart enough to do or if I need to send off lol
@@glencarlisle7710 I would send it out, you have to pin the pump, remove the fuel shut off solenoid so you can slide the rack back, then there is a special tool used to set the individual pumps in. It’s been so long since I done it I would probably mess it up, and you can mess it up and the pump stick to full throttle lol
Caterpillar pump
Amigo esa bomba lleva grados al montarse en el motor??
it was a diesel engine dance party rave
Qual é débito de plena carga desse tipo de bomba injetora cat valor em ml
good video
Amigo como hizo el acople del piñon
Como se pone a tiempo?
Hello do sell or refer me to a supplier of aftermarket barrel and plungers.
how can i send my pump to you or can you tell me how to get parts , I have oil leaking from where fuel pedal rod hook on side of pump, on my 3406B
why must people put crappy music on these videos
Wondering the same thing!
ممكن نعرف عن طرمبه كتربلر928 كهرباء كيف نعرف بحاجة لفك اذا في مشكلة في فصل في عدسه وألف شكرا
This don't really help nothing
same work done by me
STRANGE PUMP TOO MANY SHIT PARTS, JAPNES GERMANS PUMP ARE EASY AND QUICK REPAIR,
I NEVER SAW DELIVERY VALVE BROKEN IN ANY PUMP BUT I SAW IN THIS PUMP,
New palengar ka rate kya hai
السلام عليكم وين مكانكم
What is price
السلام عليكم عندك طلمبات كتر بلر 5888
Stop the stupid so called music