Hi Assar, no the engine is a show model. In Germany its far too heavy for a plane. 25 Kg is max take off weight for planes. The engine is with the new nozzle already 13 Kg. Andy
Hallo, bei meinen Tests mit Nachbrenner hab ich es mal ausprobiert. Am Anfang war so gut wie kein Unterschied. Dann fiel mir auf, daß die Drehzahl bei geschlossener Düse abnimmt. (Rückstau) Mit einem kleinen Trick im Mischer der Fernbedienung justiert und es waren 4 Kg zu messen bei gleicher Drehzahl. Man kann das auch in diesem Video höhren, wie die Drehzahl langsam abnimmt, wenn die Düse schließt. Mfg Andy
Hi Greg, man hours i didnt count, but it was a long time between regular job, family and finding the right parts. When the engine was prepared for the very first run, I spent almost 1000 Euro. The turbine wheel and ngv was 350 Euro. The pair of bearings was 180 Euro. The additional material, alloy, stainless steel, brass pipes, starter, pumps ...., Yes, I guess 1000 Euro is realistic😉 Andy
Hallo Georg, hier ist ein Video einer Schubmessung. Da hat jeder sein eigenes System. Ganz genau wirds natürlich mit Sensorik, aber für eine grobe Messung nehmen viele Bastler einfache Waagen. Der Test ist gemacht bei 50 000 von möglichen 70 000 U/ min. Man bedenke auch, daß der Schub nach oben hin steil ansteigt. Mfg Andy ua-cam.com/video/3hRBWrEpHX4/v-deo.html
Hi, I really admire your work. I am from Vietnam and am very passionate about small jet engines. Can you share your structural design drawings? I would love to learn and make one like you. Thanks very much.
Hi Keal, I dont have any plans for this engine. All is collected in my brain, but if you ask me for some measurements, I dont know😉 Check my channel, there are some vids from the build. Andy
Hi Griffin, have a look here. There is all you need, for building a jet engine! Andy www.ebay.co.uk/itm/Bauanleitung-f-Turbine-UT160-LA-Uranus-140-180N/193758716849?hash=item2d1ceb63b1:g:HgMAAOSwDrNZOmKk
@@Praendy Respekt an den Spaghettitopf Modder ! Was mir direkt einfällt: Batmobil, wie beim Unterhosenbatman aus den 60ern ;) Deinen Rasenmähertraktor zum Snowblower umrüsten. Unkraut von den Pflasterplatten ausbrennen.
Hi, nee da kenne ich nur Sintern oder Lasern, habe aber überhaupt keine Connections zu wem. Schön wärs schon einige Teile mal eben so zu DRUCKEN😉 Mfg Andy
Hi, If the nozzle is open, then you have a mass flow but the gases are slow. When I close the nozzle, the gases become accellerated and the thrust increases. I did a test with fixed nozzles. At 100 mm dia, the thrust was 16,5 Kg at only 50 000 rpm. At 90 mm the thrust was 20 Kg at 50 000 rpm. If I close the nozzle more, the egt rises and the engine gets slowed, because of too much backpressure. Andy
Does the adjustable nozzle actually increase thrust? I posted a link to your channel to AgentJayZ ua-cam.com/users/AgentJayZ and he said the adjustable nozzle only works if you have an after burner. Great engine, great project btw!
Hi, the nozzle cannot increase the thrust, but it helps to make the operation easier. During starting the engine accelerates faster and the EGT is lower, if the nozzle is open. At higher thrust, I can adjust the best values for thrust and EGT. Afterburner is in progress, then it will be more interesting with the nozzle. Thank you👍 Cheers Andy
Sehr geehrter Herr Parandi ich interessiere mich sehr für Ihr Projekt und arbeite an dem kj66-Projekt für meine Universitätsarbeit. Ich habe viele Fragen dazu, aus welcher Karte Sie dieses Düsentriebwerk gemacht haben, und ich möchte mir diese Karte ansehen. Ich warte auf Ihre Antwort. Mit freundlichen Grüßen. Ramiz khosravi
Hi Ramiz, ich habe keinen Plan für das Triebwerk. Alles ist in meinem Kopf entstanden. Fragen kann ich versuchen zu beantworten👍 Für die KJ 66 gibts doch viele Informationen. Was möchtest du wissen? Andy
There a people who like the sound of a thumping V8, but I'll always argue the noise of a jet engine starting up is the best engine noise going!
Poor neighbors! 😂 super video
The engine runs well. The nozzle is very impressive work.
Great videos man love them. Yours starts quicker than store bought ones.
I'm sure your neighbors love it too!
Great engine, great video!!! What’s the weight of the engine and what’s the max trust it gives? Loved watching it
Hi,
Pls read some comments below.
There are a bit information and almost the same question.
Andy
Always pleasing to watch
Nächster schritt Nachbrenner :)
This miniature engine works great. Good Job.
You need to make an afterburner for this engine
Que alegres deben estar los vecinos....jajajajaja
Look like you have very fine metalworking and tough material!
In welchem Bereich ändert sich die AGT wenn Du die Düse ganz auf und max geschloßen fährst?
The kid in the window is probably like “coolest dad ever”
Will you try to build an aircraft where you can fit it once you are done? 600 N is much more than the weight of the engine itself right?
Hi Assar,
no the engine is a show model.
In Germany its far too heavy for a plane. 25 Kg is max take off weight for planes. The engine is with the new nozzle already 13 Kg.
Andy
@@Praendy oh ok, so it would maybe be possible in theori but not legal?
Will afterburner be integrated on the nozzle or you got to have the pipe then the nozzle making it longer.
Hi,
already done😉
Watch
ua-cam.com/video/HFRrH56jPqg/v-deo.html
Andy
Nice 👍👍.. thrust?
How do you calculate the diffuser angles please?
How are the bearings lubricated?
Wow, how its made like these. Super awesome sounds.
Ah, you do have a variable geometry nozzle, awesome!
Hi, I just answered to the afterburner video👍👍👍
Andy
Cool hobby...not exactly stamp collecting, but way cooler 🙂
That is a really nice engine i own a ATJ-220 and is very small what size is the compressor wheel on this engine
Hi,
the comp wheel is 95 mm inducer and 142 mm exducer.
Andy
Nice engine mate. Well done. Do you have engineering drawings for this engine ? I would love to build this.
Hi Bryce,
There are no plans available.
All designed in my head👍
Andy
What nozzel is made from?
Geil, wäre ich dein Nachbar, würde ich rufen: "MACH MA LAUTER DIE KISTE!!!!" :D
Sind schon 95 Db im Leerlauf😉
Very nice an amazing piece of work!
Thank you guys!
Your collection is awesome👍
A lot of noise, you have!
Cheers Andy
What a great job! Sexy technics)
With best regards from Khabarovsk, Russia)
Hi Petr,
I love your hat👍
Thank you! Andy
Ist ein Schubunterschied messbar bei den verschiedenen Nozzle-Positionen?
Hallo,
bei meinen Tests mit Nachbrenner hab ich es mal ausprobiert.
Am Anfang war so gut wie kein Unterschied. Dann fiel mir auf, daß die Drehzahl bei geschlossener Düse abnimmt. (Rückstau)
Mit einem kleinen Trick im Mischer der Fernbedienung justiert und es waren 4 Kg zu messen bei gleicher Drehzahl.
Man kann das auch in diesem Video höhren, wie die Drehzahl langsam abnimmt, wenn die Düse schließt.
Mfg Andy
So cool I built a snowman once
Mr. Engineer, I am very interested in jet engine engineering. I want to learn from you. You will help me.
Hi Hidayat,
how can I help you?
Thats also my very first jet engine and I am happy, it works!
Andy
Teach me how to install a compressor and a compressor and how to install a turbine in such a way that I can teach you a lesson.
@@hidayatkhan9030 watch my videos part one, two and three.
There you see, how I built all parts together.
Andy
I would so love to do this. Rough estimate on how much money and man hours you have in building this so far?
Hi Greg,
man hours i didnt count, but it was a long time between regular job, family and finding the right parts.
When the engine was prepared for the very first run, I spent almost 1000 Euro.
The turbine wheel and ngv was 350 Euro.
The pair of bearings was 180 Euro.
The additional material, alloy, stainless steel, brass pipes, starter, pumps ....,
Yes, I guess 1000 Euro is realistic😉
Andy
Super super like you are the best
Wieviel Schub erzeugt das Triebwerk und gibt es eine einheitliche Methode, die Schubkraft zu messen?
Hallo Georg,
hier ist ein Video einer Schubmessung. Da hat jeder sein eigenes System. Ganz genau wirds natürlich mit Sensorik, aber für eine grobe Messung nehmen viele Bastler einfache Waagen.
Der Test ist gemacht bei 50 000 von möglichen 70 000 U/ min.
Man bedenke auch, daß der Schub nach oben hin steil ansteigt.
Mfg Andy
ua-cam.com/video/3hRBWrEpHX4/v-deo.html
You are genius, i love it
Always succes 😃😍
Hi, I really admire your work. I am from Vietnam and am very passionate about small jet engines. Can you share your structural design drawings? I would love to learn and make one like you. Thanks very much.
Hi Keal,
I dont have any plans for this engine.
All is collected in my brain, but if you ask me for some measurements, I dont know😉
Check my channel, there are some vids from the build.
Andy
@@Praendy Oh very nice, thanks you so much ♥ God Bless you Praendy
klasse
Super video.is this able to fly
I want to make my own jet engine and I would like to know what I need the jet engine to have in order for it to run like yours.
Hi Griffin,
have a look here. There is all you need, for building a jet engine!
Andy
www.ebay.co.uk/itm/Bauanleitung-f-Turbine-UT160-LA-Uranus-140-180N/193758716849?hash=item2d1ceb63b1:g:HgMAAOSwDrNZOmKk
@@Praendy Thank you!
@@griffinruddick4412 its only a plan to build one, without any parts.
@@griffinruddick4412
ua-cam.com/video/ES_9RBM1DnM/v-deo.html
Meine Nachbarn würden direkt die bullen rufen xD
What’s the nozzle supposed to do?
It changes the velocity of the gases coming out
Hi,
at higher rpm, I can adjust the best diameter for thrust and exhaust gas temperature.
Andy
@@Praendy Similar to the F-22's Vertical Thrust Vectoring
Crazy Video☺👌
What is the thrust?
Brilliant...
Sehr geil :D . Der Sound ist auch echt traumhaft :> . Packst du da auch irgendwann noch mal Flügel dran? :D
Hi,
nein kommen keine Flügel dran. Ist vom Gewicht schon zu schwer. 13 Kg
Mal sehen, was mir einfällt😉
Andy
@@Praendy aber ein wirklich schönes Teil! Respekt
@@Praendy
Respekt an den Spaghettitopf Modder !
Was mir direkt einfällt:
Batmobil, wie beim Unterhosenbatman aus den 60ern ;)
Deinen Rasenmähertraktor zum Snowblower umrüsten.
Unkraut von den Pflasterplatten ausbrennen.
Sagenhaft, das deine Nachbarn da so mitspielen. Ich mache sehr selten mal ein Test bei neu installierten System und dann nur 1-2 min ob es läuft.
Hast du dich schonmal mit 3D Druck von Metallteilen beschäftigt?
Hi,
nee da kenne ich nur Sintern oder Lasern, habe aber überhaupt keine Connections zu wem.
Schön wärs schon einige Teile mal eben so zu DRUCKEN😉
Mfg Andy
@@Praendy ist halt Wahnsinn, welche Formen auch erzielt werden können. Das war bis jetzt unmöglich.
Good work
you build or buy motor
Hi Papi,
I built the engine.
Click on my channel name "Praendy" and you see all videos.
Andy
Supper
my ears are blown 😎😎😎😎
Hi David,
in case of you can hear again, watch this one😉
ua-cam.com/video/PaGNiCVDi84/v-deo.html
Andy
ทำขายหรือเปล่า ครับ ราคาเท่าไร
Где то один Негода просит Олежек подержать его кофЭ.
I want to know how much trust can be produce by added that nozzle
Hi,
If the nozzle is open, then you have a mass flow but the gases are slow.
When I close the nozzle, the gases become accellerated and the thrust increases.
I did a test with fixed nozzles.
At 100 mm dia, the thrust was 16,5 Kg at only 50 000 rpm.
At 90 mm the thrust was 20 Kg at 50 000 rpm.
If I close the nozzle more, the egt rises and the engine gets slowed, because of too much backpressure.
Andy
The test is here.
ua-cam.com/video/3hRBWrEpHX4/v-deo.html
Please install an Afterburner to this configuration!
Hi Victor,
already done👍
ua-cam.com/video/HFRrH56jPqg/v-deo.html
Andy
Çook iyi bee
Thrust is approaching zero
Putting two of them, you could fly 200 kg aerodynamic aerial vehicle almost 1 mach
Any man who lights his DIY jet engine with a cigarette lighter gets a Like from me :D
I.Q300
😍😎😎😎
Build a jet-pack.
👍😎
Was denken die Nachbarn darüber? 😄
Hi Dmitrij,
Nachbarn?
Naja die sind alle in ihren Häusern und haben die Fenster geschlossen. Ist ja auch viel zu kalt draußen😀
Andy
Die Nachbarn wollen mehr!
@@simonw647 Dann komm morgen mal rüber😉
You need a bypass fan and afterburner tube.
Hi,
Kind of this?😉
ua-cam.com/video/HFRrH56jPqg/v-deo.html
Andy
How,to make this sir ,?kindly show this,how does make thie tobine ingine sir
Hi Samuel,
click on my channel name "Praendy"
and you find all videos👍
Andy
niceeeeeee
Does the adjustable nozzle actually increase thrust? I posted a link to your channel to AgentJayZ
ua-cam.com/users/AgentJayZ
and he said the adjustable nozzle only works if you have an after burner. Great engine, great project btw!
Hi,
the nozzle cannot increase the thrust, but it helps to make the operation easier.
During starting the engine accelerates faster and the EGT is lower, if the nozzle is open. At higher thrust, I can adjust the best values for thrust and EGT.
Afterburner is in progress, then it will be more interesting with the nozzle.
Thank you👍
Cheers Andy
@@Praendy Thanks man!
What is an EGT? Kannst auch auf Deutsch antworten
@@tolotosss Hi, egt ist die exhaust gas temperatur, also die heiße Luft, die aus der Düse kommt😉
Mfg Andy
Ach so, danke
Hey Andy do you speak English or only German?
Hi Justin,
my English is OK for a talk😉
But now I have to sleep after a nightshift.
new fleshlight design?
it blows
I challenge you to make it vector!
Hi Filipe,
I challenge myself, but not with a vector nozzle.
Its useless for an engine, what will never fly.
Andy
Itu dimana?
Hi,
Germany
don't blow away my house.
Дайте мне такой же. Пожалуйста
Wow early. Hello. First like and first comment :)
Watching Praendy ignite a jet engine with a bic lighter lol Nothing better
Sehr geehrter Herr Parandi
ich interessiere mich sehr für Ihr Projekt und arbeite an dem kj66-Projekt für meine Universitätsarbeit. Ich habe viele Fragen dazu, aus welcher Karte Sie dieses Düsentriebwerk gemacht haben, und ich möchte mir diese Karte ansehen. Ich warte auf Ihre Antwort. Mit freundlichen Grüßen.
Ramiz khosravi
Hi Ramiz,
ich habe keinen Plan für das Triebwerk.
Alles ist in meinem Kopf entstanden.
Fragen kann ich versuchen zu beantworten👍
Für die KJ 66 gibts doch viele Informationen.
Was möchtest du wissen?
Andy
Das voundabarr
🙉
Give me your jetturbo
the only subtitles are in german for a german speaking audience ... kind of fucks everyone else ...
Hi,
Subtitles are in English.
Try it😉
Andy
Maybe click German, but the subtitles showing English.
really impressive