Have you ever used a pinasco cast 5 port cylinder on a 1980 VNX 1T p125x --made for USA... I'd like to know timing jet sizes for si24/24E with auto lube..
Good evening. I would like to ask you about the carburetion for an engine equipped with VMC Stelvio, si24 (with original filter) and polinibox. In your experience, more or less, what main jet could I need?
Super. Frage: wäre es mit dem 20er auch gegangen? Ich meine 125er bissl flotter machen. Dachte an den vmc super g und eine Polin Box. Wäre der 20er da noch ok?
where js a lot of hazzle? And why taking out the whole engine if you do NOT plan to open it? its a few min for the cyl bolts. And a bit for the clutch. Way less work than engine in and out.
![[Salita dello Stelvio] Vespa PX 177 VMC Stelvio vs Malossi 210](/img/n.gif)
I used this. And this is more than pranakit/pinasco 👍
nice vid, as always..thank you
Part 2 in the next days 🍻
The cilinder just fits right on without grinding the airports for the electric starter? Regards
im using 10 inch tire../ 4th gear 36 on mainshaft and muffler polini bigbox what your suggest for ratio ? is 23/65 or 23/64..?
which setup?
love your vids
Have you ever used a pinasco cast 5 port cylinder on a 1980 VNX 1T p125x --made for USA... I'd like to know timing jet sizes for si24/24E with auto lube..
Is this setup going to be reliable/durable ?
of course BUT it depends on how well u set it, carb & ignition & esp fuel supply
Good evening. I would like to ask you about the carburetion for an engine equipped with VMC Stelvio, si24 (with original filter) and polinibox. In your experience, more or less, what main jet could I need?
120
Super. Frage: wäre es mit dem 20er auch gegangen? Ich meine 125er bissl flotter machen. Dachte an den vmc super g und eine Polin Box. Wäre der 20er da noch ok?
Ja das geht
@@FreakMoPed8 danke dir. Hast du eine Empfehlung bzgl. Düsen?
sorry, gar nicht zuhause beim si20..
Premixing in the tank or still using the autolube??
And if premixing, then what premix fuel/oil ratio??
Also why use the air filter at all??
of course with oilpumo 😉
If premix than standard 1:50
😉😉
ua-cam.com/video/nhyMkwPbs8Q/v-deo.html
thankyou 👌
Nice brother
is it okay to use a vacum cleaner to clean it up??
Sure
👍👍
Which is better sir....parmakit 177 or vmc 177?
parmakit is oldschool, vmc is newly designed = vmc is better
@@FreakMoPed8 if compare to Pinasco Magny Cours which one better?
Thank you sir...... greetings from Indonesia.i am the one your fans,always watching your videos 🙌👍👍
thx mate, cheers back from austria :)
Its never a pinascofrom the pure technical approach.
what is best gear ratio would you suggest?
setup... 😉😉
✌️
Can i optimize port timming without case porting?. Will it work fine?
yes. its a cylinder thing.
Are you doing another video on this scooter
Part two in the next days
👍👍👆
It takes like 10 minutes to take the engine out.... Why go through so much hassle
where js a lot of hazzle?
And why taking out the whole engine if you do NOT plan to open it?
its a few min for the cyl bolts. And a bit for the clutch. Way less work than engine in and out.
Lavori sporco la prossima volta metti della carta igienica con olio o una cicca di gomma prima di fare entrare polvere nel motore
👍👍👍👍