Citroen C5 Gearbox Fault Repair needed, Parking Brake Faulty, AL4 Selector Switch problem fix
Вставка
- Опубліковано 4 вер 2024
- Link to the item: ali.pub/2yefoh
Gearbox fault: repair needed + Parking brake faulty + Service
very common problem at AL4 gearbox, the MCU does not recognize P gear or every other gear (not N position calibration).
temporary solution:
1. play with the shifter, start the engine.
2. start the engine at N position.
3. comment if you have other temporary solution.
solution cost: 10-15$
30 minutes work.
After 3 years, still the most helpfull video for me, thanks!
Just to mention to all Citroen C5 X7 (III) owners - good battery is very important. A lot senzor errors and faults starts from old/bad battery !
Thank you very much. I had same problem. I saw your video and i started engine at N-position. Works fine.
I dont have replaced switch yet.
Couple days ago, R went on with noise. I started at N and after that, works fine.
Can you explain more on the calibration, do i need to mechanically shift the gear to N position before i do the calibration as per your video? if so, how do i know mechanically the gear is in N position? a very big thank you for showing this fix, really helps a lot.
How can 8 people not like this fabulous video something wrong in the head
Hello, how are you? I did the complete repair of the AL4 on my C5 2009. O' rings, the two solenoids and the entire oil replacement were changed. It worked ok ... after 1000km of repair, the gearbox gave a very strong bump and went into emergency in 3rd gear (I was getting close to the traffic light, at about 20 km/h). I hung up and started the car and the gears “came back”, but now the car is bumping in gear shifting, randomly ... sometimes without bump, sometimes with bump so hard that I even look in the rearview mirror to check if the car's gearbox didn't fall. What bothers me most is that it gives a big bump when it shifts into reverse. The reverse brake belt has also been replaced. In addition, the “manual” option works when it wants. I scanned and two errors came out: “P1710 sensor supply fault” and “P1706 press control signal fault”. Do you have any idea what's going on? Do you believe it may be the defective gear selector (showed in the video)?
Hi did u have a solution on this i have the same problem 😢,please help
Hi, I just changed the pressure and lock up solenoids and when i was about to try the car the gears don't "lock". I have to move it a little upwards for it to engage and therefore i cannot put it in park because I would need to push it forward but I can't. Will this fix it or do I have to reposition the spring index on the valves body? Thank you
Thank you very much for your video.I had a problem with my evasion 2.0 16v...can you help me..
Thank u for the solution i’m having it with my c5 2007 2.0 all the gears are lightning at the same time i’m starting it after shifting the gear to N which works will try the solution in the video
Hi is this c5 x7 (phase 3) Aren't they 6 speed automatic? This is old AL4 .
Thank you so much plase continúe upgrade videos. Greetings from Spain
What tools (numbers) did you need for this repair?
why dont you open old switch to see whats the problem?
I have a 2006 Citroen C5 model 2.0 16v (AL4) automatic transmission vehicle.
I get transmission failure when it rains.
I am getting error U1003-0103 in OBD data
In addition, the vehicle changes gears on its own while driving on the road.
When the rain stops, my car returns to normal. Errors cleared
I think part of my car is getting water and the problem persists until this water dries up.
What is the faulty part?
Help me! please
Hi my car its a 407 2.7 disel I have prnd geirbox fault the morning car was run and start bit after 2 or 3 hour not start the problem ist ?
Link to aliexpress item is not working anymore
Good stuff! I have another strange issue. I have throttle lag only when standing still or rolling very slowly. Even if if I floor the pedal, the car hesitates 1,5-2 seconds. Probing with obd and/or computer shows that the throttle signal isn't registered and suddenly it jumps up. Any ideas?
Hi,
Try to do throttle position calibration on the cold engine.
Good Luck!
@@MyCarIsCitroen Interesting that you mentioned the cold engine, is there a specific reason? As it happens, it feels like the problem is worse when the engine is warm (!). But the lag from standing still / rolling is always a big issue.. I'll try the calibration, though. To clarify, the throttle position doesn't jump up because I floor the pedal, it is always a timed delay. I can press the pedal lightly too and that registers as well, there is only a lag.
Did you solve your problem? I have the samo lag problem as you described.
I have no recognition of drive on my c5 v6 Citroen 2003 any solutins
Hello please if I start the car at N it's still behaves that way
Hello, my 2009 Citroen grand Picasso semiautomatic. I get a message "Gearbox faulty"
When i move the gear lever, nothing happened, it does not go to "'D" , it stays on "N" and sometimes the car does not start, and other times it starts. The OBD II says "Manufacturer Controlled Transmission. Code P 1834" what do you think the problem is?
How did u fix the fault
iam having same problem with my 08 c5 x7 2.0 hdi auto ...wi this work in mine.
Hi,
If you have same gearbox then, yes.
Good luck
Wat is the engine size ur one your working on
Hi,
2.0 RFJ
Moi ma Citroën c5 2008 boîte de vitesse défaillante comment faire merci
Link to the item is not working
Hi!
Last two months I meet the same problem.
When I driving suddenly engine does down and I should stop the car, put in P, turn off the key.
After that I wait for 1-2 minutes, and turn the engine on, the problem disappearing .. but it could repeat at any moment.. it's very annoying, but I love this car and don't wana change it ..
how is the name of this device which need to be replaced?
Thank you in advance! My car is 2008 2L Diesel
Hi,
Do Diagnostic
My Car Is Citroen , when you switch in D your gearbox are stoked in 3rd gear with S and ❄️snow as well or not?
The same problem with a Peugeot 206 1.6 trip tonic. 2008, do you know the reason? . I start the engine, after 20 minutes there's a jerking. Inside Dash monitor, the S and ❄️ snow start to blink and transmission enters in 3rd gear only (safe mode). Temporary fix to shut down and restart engine, then OK. I got code P1710. Did you fix yours.?
У меня проблема в том что когда на холостых я резко нажимаю педаль газа машина начинает захлебываться и троить а если ставлю наD то вообще не едет! Что мне делать помогите пожалуйста
Hi,
The best way to know for sure, do diagnostic.
Диагностика ничего не показала
No C5 II anymore :(
Увидев это видео я заметил что мой двигатель очень сильно схож с тем что на видео
Hi ,
I got this error in CITROEN C5 2011 and car gear box stuck on D3 but doing engine on and off gear box got normal and its working fine at the moment but I got brown engine light on display and its always display for engine check.
Did anyone came across this and what should I do.
Same problem here bro..did you solve it? And if yes,how?what was the problem?
Did you solve it? I still got that error from time to time...
@@lucianbuhus1150 Any solution? What was problem?
Before 2 days, I had the same problem. Yesterday I clean all BSM and ECU cable sockets and all fuses on BSM, and after that, all fine. The problem was electrical. Errors which computer stores, was cleared with Diagbox. I will check today again for problems, but I think there is no problem anymore
@@NikoloffPhotography HI - have checked that alla fault codes are gone?
We have a C5 1.6 from 2011 that cannot drive on automatic. Only 1, 3 and 5 gears go in if we drive it manually.
I have faut codes:
P0925
P0949
P1800 (fault in N position programming)
What the others mean, I do not know - reader used: DiagBox.
Здравствуйте мне нужна помощь