Glad I found your channel. After having the RTR MST 2.0 RMX for 2 years, and saving up instead of upgrading the MST, I went straight for this. Since I only had the RTR I’m glad this is already setup well out the box, but now comes the interesting part of choosing the right electronics for it and installing/setting them up correctly. I could go the middle route and buy a GYD450 or V4 Gyro, combine that with the 4PM transmitter, a Reve D RS-ST Servo and motor/esc/vario combo, but I’m not yet sure if that’s the right choice. The other option is to go all the way with a 7PX or 10PX, GYD550, CT700 (or Reve D RS-ST), etc… Any thoughts? I for sure want a wobble-less AVCS gyro, and a slow and smooth servo. Both versions should deliver that, although I guess that the more expensive route would be more appropriate for such a chassis. It might take me a couple months until I’m able to buy everything, but I kept the RTR for that reason until then. 😂
You'll be happy with any of those electronic combos...the more higher end stuff the more tuning options will be available on radio/gyro/servo/esc. If you want to be able to adjust everything or most things from the radio you will need to have all the same brand gear IE all Futaba or all Sanwa. Servo i would recommend a fast servo (Reve-D RS-ST is programmable so can make it slow or fast) mostly then the car can switch direction quickly. You will be happy with the middle route or the high end route (Go high end, go for it!) :D
Forgot to reply my bad! Well the MD is a completely different design to the YD2 so it will be interesting to drive them side by side. The MD has big shoes to fill in my opinion.
I haven;t used the CT701 yet but I think the CT701 will be faster/snappier than the Reve D RS-ST. My OMG Bad Shoppe NBS-LP-16BF Servo is faster out of the box than the Reve-D RS-ST, even after turning up the Reve-D RS-ST servo to max speed.
Hello :) I would go for the ZX because it has a bit more refinement and flex than the SX3. Both are great cars and i like both of those platforms but I would do the ZX :D
Factory box settings as it comes from Yokomo's team driver. There was no setup sheet provided with the settings written out so I will have to do it manually, check back soon :)
Ok so update on the setup for the limited ZX - I have put the basic setup info that I recorded to a setup sheet on the video's description. If you want my hand written setup sheet of the out of box settings in full send me a direct message :)
The Reve-D RS-ST servo will not fit in this MD 1.0 chassis. The RS-ST is 3mm taller than the actual classification sizing for a "low profile" servo. I suspect there might be a fix but not yet, the MD 1.0 follows the YD-2 ZX servo mounting design.
Oh yiss that is what i meant...the RS_ST does not fit YD-2 ZX or MD 1.0. The extra 3mm on the RS-ST makes the servo horn hit the bulkhead on the ZX and offsets the servo horn position on the MD. I think some people are trying to create a fix but those chassis were just designed to the exact spec for low profile with little tolerance for fitment. SD 1.0 might be different as it is YD-2 based and remixes a lot of parts between the base and high end versions.
@@BadShoppe thanks! The SD 1.0 has a vertical servo mount, but upside down right? Looks pretty tight as well, that’s why I’m worried the RS-ST might not fit…
correct, as the SD 1.0 uses a slide rack so the servo mounting is the version from the SX3's I believe. ZX is when the servo started being mounted right side up hehe
Used to race an old tamiya TL01 indoor/carpet with a stock 540 motor.. mad fun.
Shits come a long wayyyy. Nice one boys 😂🤘
"It's touring cars with maddddd oversteers" is how i describe it to racers who want to try drifting :D
yes amazing video with amazing driving ;) loved how the car felt
awesome rc and cool drifting,nice shakedown
Hi. I’m looking at buying a new chassis for indoor carpet. What would you advise? No budget
Glad I found your channel.
After having the RTR MST 2.0 RMX for 2 years, and saving up instead of upgrading the MST, I went straight for this.
Since I only had the RTR I’m glad this is already setup well out the box, but now comes the interesting part of choosing the right electronics for it and installing/setting them up correctly.
I could go the middle route and buy a GYD450 or V4 Gyro, combine that with the 4PM transmitter, a Reve D RS-ST Servo and motor/esc/vario combo, but I’m not yet sure if that’s the right choice.
The other option is to go all the way with a 7PX or 10PX, GYD550, CT700 (or Reve D RS-ST), etc…
Any thoughts?
I for sure want a wobble-less AVCS gyro, and a slow and smooth servo.
Both versions should deliver that, although I guess that the more expensive route would be more appropriate for such a chassis.
It might take me a couple months until I’m able to buy everything, but I kept the RTR for that reason until then. 😂
You'll be happy with any of those electronic combos...the more higher end stuff the more tuning options will be available on radio/gyro/servo/esc. If you want to be able to adjust everything or most things from the radio you will need to have all the same brand gear IE all Futaba or all Sanwa. Servo i would recommend a fast servo (Reve-D RS-ST is programmable so can make it slow or fast) mostly then the car can switch direction quickly. You will be happy with the middle route or the high end route (Go high end, go for it!) :D
@@BadShoppe thanks!
What do you think about the MD 1.0 (MDR010) vs the limited 100 YD-2 ZX?
@@BadShoppe is the CT701 a better choice for the GYD550 and 10PX then, or should I still got Reve D RS-ST?
Forgot to reply my bad! Well the MD is a completely different design to the YD2 so it will be interesting to drive them side by side. The MD has big shoes to fill in my opinion.
I haven;t used the CT701 yet but I think the CT701 will be faster/snappier than the Reve D RS-ST. My OMG Bad Shoppe NBS-LP-16BF Servo is faster out of the box than the Reve-D RS-ST, even after turning up the Reve-D RS-ST servo to max speed.
Hi NezO - which chassis would you prefer ? The Yokomo YD2ZX Red (unbuilt kit) vs. YD2 SX3 Red?
Hello :) I would go for the ZX because it has a bit more refinement and flex than the SX3. Both are great cars and i like both of those platforms but I would do the ZX :D
Nice Run
Thank youuu!
What camera do you use for filming?
I use a Samsung Galaxy S20 phone, Go Pro Hero 7 Silver and Go Pro Hero 4 Session cameras.
What pinion gear is that it's nice
Pinion gear used is a 24 tooth, 48 pitch gear supplied by Yokomo.
Gucci
Mane in 2006
What are your settings on this - Camber/ride height/etc??
Factory box settings as it comes from Yokomo's team driver. There was no setup sheet provided with the settings written out so I will have to do it manually, check back soon :)
Any updates on the set up?
Ok so update on the setup for the limited ZX - I have put the basic setup info that I recorded to a setup sheet on the video's description. If you want my hand written setup sheet of the out of box settings in full send me a direct message :)
Does the RS-ST really not fit?
Are there solutions to this?
The Reve-D RS-ST servo will not fit in this MD 1.0 chassis. The RS-ST is 3mm taller than the actual classification sizing for a "low profile" servo. I suspect there might be a fix but not yet, the MD 1.0 follows the YD-2 ZX servo mounting design.
@@BadShoppe I meant the ZX, sorry.
Ok so the RS-ST doesn’t fit in the ZX and the MD 1.0?
Is there a fix for the ZX?
How about the SD 1.0?
Oh yiss that is what i meant...the RS_ST does not fit YD-2 ZX or MD 1.0. The extra 3mm on the RS-ST makes the servo horn hit the bulkhead on the ZX and offsets the servo horn position on the MD. I think some people are trying to create a fix but those chassis were just designed to the exact spec for low profile with little tolerance for fitment. SD 1.0 might be different as it is YD-2 based and remixes a lot of parts between the base and high end versions.
@@BadShoppe thanks!
The SD 1.0 has a vertical servo mount, but upside down right?
Looks pretty tight as well, that’s why I’m worried the RS-ST might not fit…
correct, as the SD 1.0 uses a slide rack so the servo mounting is the version from the SX3's I believe. ZX is when the servo started being mounted right side up hehe