Smooth vibration and in precision,, i liked this video because it plays smooth also not like to the other's video it plays very fast so the audience cannot understand what they want to be seen and think but this one is transparent and understable. Great idea and job well done sir👍
This is a bosch pro more cheaper than bosch, yup you can buy a cheap table saw than make this but it needs calibration and the top table is not wide. this is optional 😁
There are a number of YT videos on tools called 'ultimate' of 'perfect' - but they are made of wood. Any quality table saw will have major components made from cast iron. This is not for fun- there are good reasons.
This would be a great platform for someone that wanted to build a table saw which is servo/stepper motor controlled so as to get precise angles, cuts and perhaps an automatic feed.
well made video. One thing though the trunions seem to be incorrect in design they should place the tilt centre of the blade at the top of the table surface so the blade comes out of the same slot for both 90 and 45 degrees. As you have made them they tilt below the table and toy might as well have simply used pivots under the table top. Several table DIY makers show how to design the trunions where the tilt is projected to the top of the table and where to place the centre of the trunion circles compared to the chassis and table top.
Great project, liked moment when we should see saw blade kiss the fence nice and parallel camera suddenly blurs out lol. You could’ve done it adjustable, though. Seriously man, very inspiring and great project, no kidding.
Instead of using a linear bearing, which adds complication, a single point tilting raise setup is preferred. It's also good because you can put a single strong pivoting point, and use trunnions to make it super rigid.
This is a great build and it turned out fantastic. If there was just one thing that I would point out that you did wrong. Your trunnion centre point shouldn't be lined up with the top of the sawblade block but rather the centre needs to line up with the table top - All you would need to do it cut the thickness of the table top off the trunnion and move it up. You can see the issue the current setup causes at 22:30 where the plate has had to be removed to tilt the blade - with the size of the slot in the plate you should be able to tilt to 45 degrees without removal but the issue that you are having is because the trunnion is off... Other than that it is a fantastic build, thanks for making this video! 👍
Overall great work, but with a problem in the configuration of the trunnion as is clearly visible in the video the blade can not be tilted to 45 degrees without having to change the top cover and also is a large gap between the top and blade saw. You have to take into account the thickness of the top and that the "pivot" point is at the top of this top, on the other hand the cut that you make at 45 degrees in the mobile part of the trunnion is not correct because in this way it will never be possible for the disc to tilt at 45 degrees because the trunnion will hit the bottom of the top well before the disc reaches this inclination, say you have to cut more. As I said the rest is well done but it is a shame that it is ruined by the poor configuration of the trunnions, you should fix that and you would get an excellent saw.
@@plywoodworking Dei disegni non mi hai detto niente, mi piacerebbe averli per provare a farlo. Non ti faccio concorrenza, sono un vecchietto con l'hobby del legno. Di nuovo bravissimo un saluto Maurizio
Masya Allah... Bagus Om... Kayaknya posisi engsel(gak tau namanya) yang buat ngatur derajat kemiringan blade di kurangi 18mm(sesuai ketebalan top table) apa ya om? Biar posisi pusat derajat tepat ada di permukaan top table. Jadi kalo mau diatur kemiringan ndak perlu ganti insert lagi.
Selama ini sih klo tiap mau miring harus ganti insert mas kecuali lubang insertya gedhe, klo ini posisi insertya agk lebar coz aq ngejar selang dust collector ddlm kabinetya jdi posisi trunionya agk setengah lingkaran, klo mau agk sempat dikurangi ukuran trunionya. Ato ada cara lain tp ketebalan bladeya berkurang gk sampe 8cm
Yup 71/4 until now still work strong, dont push to hard and cut hardest wood with high thickness. Recomeded using trust brand like makita, bosch dewalt and etc. But if not sure using standart size blade
Saya mencoba membuat sendiri, namun fence penjepit bagian depan dan belakang seperti dua benda yang tarik menarik. Uniknya bagian depan menahan terlebih dahulu sehingga saya harus mengukur manual jarak fence kegergaji agar antara bagian depan dan belakang sama jaraknya. Dan saya belum menemukan cara yang pas.
Have you made plans for this table saw build and if so could I purchase them. I will have all the bearings and linear parts shortly coming by mail. Thanks Rowe.
This is additional upgrade, i give text you can follow this or not! (If not believe with the machine don't follow this step). I know not design for 10 but i trust with bosch brand, working for me i combine with freud blade still power full for cut hard rosewood
If you add “ultra high molecular weight plastic (UHMW)“ underneath the locking mechanism front and back of your fence, it should help the fence glides left and right more smoothly.
Great job and highly inspiring. Have plans to build a circular saw into my workbench in the garage and I will most likely borrow some of your ideas. A question though. You don't find that a blade bigger than what you normally could fit in the saw you used gets too much for the motor to handle?
@@plywoodworking yang di sistem naik turunnya itu, terima kasih berbagi ilmunya mas, saya udah bbrpa kali mencontoh ide2 briliannya, sangan mudah d pahami.. terima kasih
Harus berkorban klo ambil smua namaya serakah😁, kerja sndirian gk mkn bs smua ambil orderan jg ngerjain konten. Tutorialya komplit mas ikutin aj step by step
![[Woodworking DIY] Make your own table saw with Makita circular saw / Main body production](http://i.ytimg.com/vi/jvOZNiS4-zg/mqdefault.jpg)
This is one of the best tutorials I have ever seen on youtube, and I have been watching for decades
Thank you very much!!! 👍👍. glad you enjoy this video
It looks better then your old Stanley table that you owned. So stunning to look at
You right, i sell my old table saw stanley and build this. I suprised with the result low vibration and powerfull
BRILLIANT! As we say in America, “Give yourself a pat on the back!” Nicely done.
Thank you very much!👍😊👍
Smooth vibration and in precision,, i liked this video because it plays smooth also not like to the other's video it plays very fast so the audience cannot understand what they want to be seen and think but this one is transparent and understable. Great idea and job well done sir👍
Awesome, thank you!
First class workmanship sir!
Thank you very much!👍😊👍
Thanks for your video
Most welcome
masbro,tutarial mu sangat mendidik dan jelas .lanjutkan
thank you very much 👍👍
Very useful Video for small shops. I really thank you for sharing the detailed information about making this Table Saw. Really nice work 🫡
You are very welcome
thanks man. you have a big and mercifule soul and spirite.....
I appreciate that!
Wow, you're and absolute genius, beautiful skills and a very good concept.
Thank you for sharing
Thank you very much!
Meticulously wonderful DIY tool ever made on a vid!
Wow, thanks!
Amazing craftsmen ship. Very very good.
Merci beaucoup pour la vidéo
Cheaper to buy a table saw rather than destruying an expensive Bosh i think 😊
This is a bosch pro more cheaper than bosch, yup you can buy a cheap table saw than make this but it needs calibration and the top table is not wide.
this is optional 😁
Thanks great vedio. I seen many vedio and all r was so confusing but ur vedio is very good.
Thanks and welcome
very creative, quick, easy off switch specially in a situation of stress.
Glad you like it!
Great job with this project. I like that Wood-Plastic composite material. I'll hang on to this one for some how-to ideas. Thanks for posting.
thank you 👍👍
Nice job! thanks for sharing your experience
Thanks for watching!
AMAZING!
There are a number of YT videos on tools called 'ultimate' of 'perfect' - but they are made of wood. Any quality table saw will have major components made from cast iron. This is not for fun- there are good reasons.
Big fan my friend, all respect to your work
Thank you so much 😀
Que belleza como me gustaria hacerme uno o mandarlo hacer. Pero aqui en Venezuela todo es caro
Great work man.
Appreciate it!
This would be a great platform for someone that wanted to build a table saw which is servo/stepper motor controlled so as to get precise angles, cuts and perhaps an automatic feed.
thank you very much!!
"...and on the 7th day He rested." 😇
well made video. One thing though the trunions seem to be incorrect in design they should place the tilt centre of the blade at the top of the table surface so the blade comes out of the same slot for both 90 and 45 degrees. As you have made them they tilt below the table and toy might as well have simply used pivots under the table top. Several table DIY makers show how to design the trunions where the tilt is projected to the top of the table and where to place the centre of the trunion circles compared to the chassis and table top.
thank you very much!!!
Great project, liked moment when we should see saw blade kiss the fence nice and parallel camera suddenly blurs out lol. You could’ve done it adjustable, though.
Seriously man, very inspiring and great project, no kidding.
Thanks for the tips!
Огонь 🔥всё здорово, а главное аккуратно, лично я балдею 👍☕
Thank you very much!
Complimenti. Davvero un ottimo lavoro!
Thank you so much 😀
Absolutely fantastic job ... even the video is well done. 🙏🏻💜🇨🇦
Glad you enjoyed it!
Wow amazeing working i like u project
Thank you so much 😀
Adorei muito bom maravilha, parabéns pra vc.😃
Instead of using a linear bearing, which adds complication, a single point tilting raise setup is preferred. It's also good because you can put a single strong pivoting point, and use trunnions to make it super rigid.
thank you very much!!!!
One of the best I've seen. Nice table!!
Wow, thanks!
Perfect Stép by Stép tutorial
Thank you very much!👍😊👍
Maravilloso... Felicitaciones, un abrazo desde Perú.
Many many thanks
Nice
Thank you very much!👍😊👍
Meu sonho era presentear meu filho com uma mesa dessa
thank you very much!!
Sou um brasileiro sonhador e não tenho condições de ter uma bancada dessa 😔 mais um dia Deus irá me ajudar ✋ eu tenho muita fé nele!!!
Very nice indeed 👍🏼
Thank you very much
Nice job, its perfect...
Thanks a lot!
Tres beau travail, belle précision 👍magnifique 👍👍👍👍👍
Thank you very much!
Great job on the table saw build Friend! really turned out nice :) Thank you for sharing the video with us!💖👍😎JP
Thank you! Cheers!
@@plywoodworking Your very welcome Friend! Have a awesome week!😎
전송 고맙습니다 UA-cam 영상을 을 매일 보고 잇어 요 볼수록 신기 합니다 Regd Kbl
amazing job
Thank you very much!
This is a great build and it turned out fantastic. If there was just one thing that I would point out that you did wrong. Your trunnion centre point shouldn't be lined up with the top of the sawblade block but rather the centre needs to line up with the table top - All you would need to do it cut the thickness of the table top off the trunnion and move it up. You can see the issue the current setup causes at 22:30 where the plate has had to be removed to tilt the blade - with the size of the slot in the plate you should be able to tilt to 45 degrees without removal but the issue that you are having is because the trunnion is off...
Other than that it is a fantastic build, thanks for making this video! 👍
thank you very much!!!
És um VIRTUOSO...Parabéns...Abraços...
Thank you very much!👍😊👍
Just perfect
Thank you very much
Your amazing.
Thank you very much
Overall great work, but with a problem in the configuration of the trunnion as is clearly visible in the video the blade can not be tilted to 45 degrees without having to change the top cover and also is a large gap between the top and blade saw. You have to take into account the thickness of the top and that the "pivot" point is at the top of this top, on the other hand the cut that you make at 45 degrees in the mobile part of the trunnion is not correct because in this way it will never be possible for the disc to tilt at 45 degrees because the trunnion will hit the bottom of the top well before the disc reaches this inclination, say you have to cut more. As I said the rest is well done but it is a shame that it is ruined by the poor configuration of the trunnions, you should fix that and you would get an excellent saw.
Thank you very much 👍👍
Hai fatto un ottimo lavoro. Mi piacerebbe realizzarlo, mi aiuteresti mandandomi i disegni? Di nuovo bravissimo.
thank you very much glad you like this
@@plywoodworking Dei disegni non mi hai detto niente, mi piacerebbe averli per provare a farlo. Non ti faccio concorrenza, sono un vecchietto con l'hobby del legno. Di nuovo bravissimo un saluto Maurizio
So nice
Very nice
Damn, I want that saw, amazing job man!!
thank you very much!!
Классная работа.спасибо
Thank you very much!👍😊👍
Well done
Thank you very much!👍😊👍
Норм получилось. Лежит циркулярка с 235 диском ждёт своего часа.
thank you
Sense and advantage of trunnions? Turning point of the sawblade can be put into the surface of the desk.
100% agree
Excelent video 👏 👏 👏
Thank you very much!👍😊👍
keren bang, ijin bikin ya
siap smoga bermanfaat
TÉ agradezco mucho tu atención y generosidad por compartir exelente herramienta bien detallado disculpa lo tarde 👌👍😎😊
thank you very much!!!!
Do you know if I buy HMR in the USA
Masya Allah... Bagus Om...
Kayaknya posisi engsel(gak tau namanya) yang buat ngatur derajat kemiringan blade di kurangi 18mm(sesuai ketebalan top table) apa ya om? Biar posisi pusat derajat tepat ada di permukaan top table. Jadi kalo mau diatur kemiringan ndak perlu ganti insert lagi.
Selama ini sih klo tiap mau miring harus ganti insert mas kecuali lubang insertya gedhe, klo ini posisi insertya agk lebar coz aq ngejar selang dust collector ddlm kabinetya jdi posisi trunionya agk setengah lingkaran, klo mau agk sempat dikurangi ukuran trunionya. Ato ada cara lain tp ketebalan bladeya berkurang gk sampe 8cm
Jos banget mas did...
maksih banyak mas
nice diy table saw i ever see ..... but i didnt want cut any original circular saw parts
Thank you very much, yes that optional coz i want use 10' blade normal max only 8'
is that a 7¼ circular saw?.,im wondering if it can run a 10" blade without over heating
Yup 71/4 until now still work strong, dont push to hard and cut hardest wood with high thickness. Recomeded using trust brand like makita, bosch dewalt and etc. But if not sure using standart size blade
how did you align the miter tracks to blade? bit confused. im trying to follow this and build it.
Using blade for main align, same like the fence, i using blade for setup fence
👌👌👌👌👌♥️♥️♥️♥️♥️
thank you very much glad you like this
Saya mencoba membuat sendiri, namun fence penjepit bagian depan dan belakang seperti dua benda yang tarik menarik. Uniknya bagian depan menahan terlebih dahulu sehingga saya harus mengukur manual jarak fence kegergaji agar antara bagian depan dan belakang sama jaraknya. Dan saya belum menemukan cara yang pas.
Yg utama buat dlu dri bagian toggle clamp pastikan lurus dgn blade bru buat pengungci tamnahan, cara itu lbh gampang drpd dibalik
@@plywoodworking kekuatan berapa KG minimal toggle klam untuk panjang 80cm agar kokoh. Terima kasih sudah merespon
Muy buen trabajo , como descargo el pdf ?
plan available on plywoodworking group and page on FB
Asli....keren..👍👍🙏🏻🙏🏻
Thank you very much!👍😊👍
Buongiorno mi è piaciuto il suo video volevo sapere che tipo di materiale ha usato?
La ringrazio
thank you very much!!!!
Lost audio at 7:58 😢 || back on at 11:38 😁 Audio off at 17:26 again and back on at 17:55 (music)
Without a doubt, it is a wonderful job. I have just one question.
How much time and money did you invest to do it?
Thank you very much, i made this need 1 week and spent $150, but the result made me happy
Have you made plans for this table saw build and if so could I purchase them. I will have all the bearings and linear parts shortly coming by mail. Thanks Rowe.
i will message you if the plan ready, give you email
Dari kota mana anda brasal
Sy dri surabaya mas
@@plywoodworking saya kagum sama anda . Saya baru tau kalo ada channel pertukangan yang luarbiasa baru kali ini . Salam dari Cilacap . Jateng
Keren banget guruku 🙏🏿🙏🏿
maksih banyak mas
ukuran bevel gear sama no bearingnya barapa yach...sekalian minta link online shop yang jual komponen tsb...makasih info dan ilmunya...
Itu bevel pya stanley cri onlien banyak kok
❤👍
Thank you very much 👍👍
I wonder if you would give me the detail dimension sir ?
Great job! Have the plans avaliable?
will be ready soon
Increasing the blade size increases the load on the motor which it is not really designed for, any problems?
This is additional upgrade, i give text you can follow this or not! (If not believe with the machine don't follow this step). I know not design for 10 but i trust with bosch brand, working for me i combine with freud blade still power full for cut hard rosewood
Om yg buat turning nya pake hmr brp mm itu ? Lapis 2 kyk nya ya
18mm, cm 1 lapis aj
Ficou muito bom
Thank you very much!👍😊👍
Minute 5:55 gives me the creeps. No drilling with glovees on!😧
That the camera angle makes the finger look more closer on the drill bit. I cant work wothout gloves coz my thumb feel hurt.
Thank you
great video
do you have plans?
pkan will be ready soon!
If you add “ultra high molecular weight plastic (UHMW)“ underneath the locking mechanism front and back of your fence, it should help the fence glides left and right more smoothly.
Thank you for information, i will try search that material👍🏻👍🏻
@@plywoodworking If you can't find UHMW, cutting board is a good choice. It is slick plus very hard.
Oh yes i know that, hard and very slick. Thank you very much for information. That good idea👍🏻👍🏻
السلام عليكم ورحمة الله وبركاته
كم رقم جوالك ؟؟؟؟؟؟
thank you
Incredibly nice!! I love it. How much would it cost to build me one like that?
Thank you very much, build this i need $150-$165, linear bearing need a lot cost
Amazing ! This video gave us fine information from design to fabrication. It is really professional standard. Thanks for your sharing !
Many many thank for your comment, glad if you like this project😊
Mantappp...
Thank you very much!👍😊👍
mas, itu multipleksnya habis berapa ya?
3 lembar
What cad software your using?
Autodesk 3D max sofaware
Mas, penggaris yg item itu apa namanya? Ehehehe
multi gauge ada saya review videoya
without the circular saw, how much the budget for this ultimate table saw?
Almost $200 without circular saw, range $180-189
such a great design, do you have a detailed blueprint? can you share it with me? I am very grateful! how can i contact you?
You are very welcome, i really sorry plan not yet available coz now i very busy renovation my shops
Think it is Beautiful! Such skill!
However, I won’t subscribe because too many Commercials.
Thank you! LoL commercials not from me😅
Great job and highly inspiring. Have plans to build a circular saw into my workbench in the garage and I will most likely borrow some of your ideas. A question though. You don't find that a blade bigger than what you normally could fit in the saw you used gets too much for the motor to handle?
Thank you very much
Do you have plans for it
I hope it's free
All free for plan,but for this project not yet finish all
Itu pakek as besi yg ukuran berapa mm om? Terima kasih
As besi yg mana mas, rata2 pake 12mm drat bautya 10mm br kuat lbh besar lbh bagus mlhan
@@plywoodworking yang di sistem naik turunnya itu, terima kasih berbagi ilmunya mas, saya udah bbrpa kali mencontoh ide2 briliannya, sangan mudah d pahami.. terima kasih
As naik turunya pake 12mm bnrya mau pake 16mm tp terlalu mahal hargaya😅
Kalo bearengnya type dan ukuran apa om yang pas dengan drat bevel
bisa order buat dudukan cs hitachi g om? nanti iklankan di tokped
Smtra ini gk trima orderan mas, gk tau jga gmna bentuk csya😅. Gk keburu waktuya
@@plywoodworking sudah disibuk bikin konten ya mas 😁😁
Harus berkorban klo ambil smua namaya serakah😁, kerja sndirian gk mkn bs smua ambil orderan jg ngerjain konten. Tutorialya komplit mas ikutin aj step by step
Я не понял что то как прямолинейное вращение превращается в круговое?
thank you very much!!
Who buys a brand new circular saw to make a table saw?
I bought a second circular saw from my friend