Brilliant video !, may i bring to your attention another manufacturer fault, after a while the front touch panel will short and the machine will not respond to input using the touch pad, the problem is water ingress behind the black cover that protects the touch pad, i disassembled the door then removed the black cover, dried the circuit board thoroughly, i then reassembled the black cover but then sealed it in by applying a generous amount of silicone sealant around the black cover then covered the black cover with plastic to ensure no more water ingress, works a charm now.
I agree with the other comments, pictures or arrows would be helpful. I believe I may have shorted mine out, too, because I used my empty dishwasher as a drain rack when I only had a few dishes to hand wash. I"m sure the extra water found its way around to the control panel because its directly below the door when its open. Thanks for the lead. :)
Mate, this is brilliant, thank you so much for a great video on how to disassemble the dishwasher, I found the fault, it was the cable from the CPU to the front door control panel,it was broken the cable must have got pinched some how when the door is opened or closed,not the best design and cut the earth wire in the cable, I pulled it out and repaired it, works a treat , Thank you
Hi mate, I'm glad you could be able to fix your problem. Since we work very hard in our warehouse making free video guides, you can always donate us via www.how-to-repair.com/help/buy-paul-a-beer/ Could you also do me a favour and take part in a poll I've made about the lifespan of appliances? You just need to tick one of two boxes. It will only take about 10 seconds. This might help us improve how machines are made in the future😇 Here's the poll question: www.youtube.com/@How-to-repair/community Also sharing will get more people to participate and we will have a greater impact with the manufacturers thank you for helping.
To help you progress with code E1 , instead of using vinegar as suggested in some posts i used the household limescale remover VIAKAL , this works effectively in removing limescale quickly, obviously use gloves when using Viakal and always perform a cycle without cutlery before starting normal use again. (UPDATE), my dishwasher ran the E1 code, i identified the problem, where the water enters the machine ,behind the panel, theres a 90 degree pinch point, over time, hard water can restrict the flow hence the E1 code, so i injected Viakal down the tube, let it settle and then re-assembled, no more E1 code now and if it happens again i know where to look.
Great video! Seems relatively easy to tear down. Im getting an E1 error on mine during what seems to be the last cycle, not quite sure where to begin to look after seeing the cycle chart.
I don't know if you're reading the comments here but I've just torn it down and everything regarding the inlet seems to be fine. Could it be that the impeller isn't reading the amount of water correctly and it's thinking that there isn't enough water (or there actually isn't enough water) to finish the cycle therefore throwing up the error?
Hello, thank you for a great video!! My issue is that the dishwasher is not draining the water and after a while when the amount of water is too big in starts overflowing and starts e4 error. Don’t you know what might be the issue ? It is not clogged I checked that
It would be great to get a video of the front control panel. My buttons stopped working. Had to leave it out in the sun door open for hours to dry it out.
My dishwasher stopped working, panel doesn’t turn on, only the internal light turned on. Where could I found pdf of the workshop manual you mentioned ? First time try to repair something 😅. Do we have some video showing how to remove the front door? Thank you ！
It seems E-3 code is a fairly common problem for the ICUIRE brand countertop dishwasher? I was very careful with it and took care of the machine. Never loaded it without scraping the dishes first, keep the filter free of detritus and would air dry the filter and screen. I accidentally ran it without the filter and that is how I earned my E-3 code. Would appreciate a future DYI or some advice on what to look for. I will subscribe because I plan to fix this myself. Thanks in advance either way! Addendum -ICUIRE advises to tilt the machine for an approximate number of minutes if the machine registers an E-3 code. Why and what component would possibly benefit from this action?
Hi there. Thank you so much for this brilliant video. I have the same device and l would like to ask you if you know what’s wrong when the main pump doesn’t start but the timer keeps counting down…
Hi there, I get very humbled by your comment. I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍
Thanks so much for this! I have an ed fault, and it sounds like you are saying if I can't just find a loose connection replace whole machine is that correct?
Thanks so much for this, helped my find the blockage (it was corn, its always fucking corn!) and flushed it out. Had to yoink the little side tank out of the pipes, so the clamps aren't 100% but it should be fine. Will let you know in the morning!
hope everything goes well @mitchywilson9892 please remember to subscribe to our channel as that really helps us ua-cam.com/users/shortse432SAb2g08 Thanks, Paul 👍
My mum recently got a new dishwasher and gave me her countertop Klarstein mini dishwasher but it's displaying an E1 error code. I've tried a few things suggested on youtube, such unscrewing the little panel near the inlet valve and looking for blockages. I even poked a pipe/straw cleaner in and out the inlets just in case anything was stuck. I tried tipping the machine at an angle over the sink to try and drain the "overflow reservoir" only to have water come out of the top bit where you put the water in and it went everywhere! It didn't come out the from the front corner under the door like one video suggested XD Nothing has worked yet, any suggestions? I love your video, I didnt even know what an inlet valve was a couple of days ago, but it was the bane of my life trying to work it out from the manual. (Spoiler alert it doesn't tell you lol) The manual really doesn't go into detail on what to do in case of error codes if you're not a pro or don't know the lingo, so I was just kinda like, "where the heck is the inlet valve?? What even IS an inlet valve??" So, long story short, I now know what an inlet valve is, but I still don't know what to do to resolve the issue with it 😂 Any advice would be much appreciated! I really want to give this machine another shot, it seems like such a waste not to!
@@nevebrown9206 I fixed it! On the inside if the dishwasher, there's a really small hole on the left wall (your left). I put vinegar in it with those measuring syringe things with a wide nozzle, you press it in quick and fast so there's pressure behind it and also i poured a bunch of vinegar in the tank with the water. If you leave it for a bit, repeat, and then run it a couple times, water starts leaking out of the small hole, and then boom, suddenly it starts working! I'm assuming it was limescale buildup. I used white wine vinegar cause that's all I had, but it might work better/ cheaper with your normal white vinegar:) be generous with it so it gets in all the nooks and crannies! I was so delighted! Can't take credit for it, a lady made a video showing how to do it, it worked and made me so happy! It's worked absolutely fine ever since
Hi, we have just randomly started having issues with our mini midea. It seems to randomly stop (at different times) during cycles, and then will just beep every minute or so. We’ve had to end up emptying the water by tilting it from the main compartment each time this has happened. No error codes are coming up. Can you help?
Thanks for your video. I didn't know there was an element to heat the water and I was supposed to only fill the tank with COLD water. I wonder if I accelerated the rate at which it broke. :(
Brilliant video !, may i bring to your attention another manufacturer fault, after a while the front touch panel will short and the machine will not respond to input using the touch pad, the problem is water ingress behind the black cover that protects the touch pad, i disassembled the door then removed the black cover, dried the circuit board thoroughly, i then reassembled the black cover but then sealed it in by applying a generous amount of silicone sealant around the black cover then covered the black cover with plastic to ensure no more water ingress, works a charm now.
i am currently having this issue, do u mind making a guide to fixing this please?
Same - some buttons on the touch panel will not work… is there someplace to buy replacement parts ?
Thank you! I'm having the same problem. I hope your solution is the fix to my problem.
I agree with the other comments, pictures or arrows would be helpful. I believe I may have shorted mine out, too, because I used my empty dishwasher as a drain rack when I only had a few dishes to hand wash. I"m sure the extra water found its way around to the control panel because its directly below the door when its open. Thanks for the lead. :)
Thank you, great information!
Mate, this is brilliant, thank you so much for a great video on how to disassemble the dishwasher, I found the fault, it was the cable from the CPU to the front door control panel,it was broken the cable must have got pinched some how when the door is opened or closed,not the best design and cut the earth wire in the cable, I pulled it out and repaired it, works a treat , Thank you
Hi mate, I'm glad you could be able to fix your problem. Since we work very hard in our warehouse making free video guides, you can always donate us via www.how-to-repair.com/help/buy-paul-a-beer/
Could you also do me a favour and take part in a poll I've made about the lifespan of appliances? You just need to tick one of two boxes. It will only take about 10 seconds. This might help us improve how machines are made in the future😇
Here's the poll question: www.youtube.com/@How-to-repair/community
Also sharing will get more people to participate and we will have a greater impact with the manufacturers thank you for helping.
شكرا لك تعلمنا منك الكثير صديقي المهني تحياتي من الريف شرق المغرب أفريقيا
To help you progress with code E1 , instead of using vinegar as suggested in some posts i used the household limescale remover VIAKAL , this works effectively in removing limescale quickly, obviously use gloves when using Viakal and always perform a cycle without cutlery before starting normal use again. (UPDATE), my dishwasher ran the E1 code, i identified the problem, where the water enters the machine ,behind the panel, theres a 90 degree pinch point, over time, hard water can restrict the flow hence the E1 code, so i injected Viakal down the tube, let it settle and then re-assembled, no more E1 code now and if it happens again i know where to look.
Great video! Seems relatively easy to tear down.
Im getting an E1 error on mine during what seems to be the last cycle, not quite sure where to begin to look after seeing the cycle chart.
I don't know if you're reading the comments here but I've just torn it down and everything regarding the inlet seems to be fine.
Could it be that the impeller isn't reading the amount of water correctly and it's thinking that there isn't enough water (or there actually isn't enough water) to finish the cycle therefore throwing up the error?
Hello, thank you for a great video!! My issue is that the dishwasher is not draining the water and after a while when the amount of water is too big in starts overflowing and starts e4 error. Don’t you know what might be the issue ? It is not clogged I checked that
It would be great to get a video of the front control panel. My buttons stopped working. Had to leave it out in the sun door open for hours to dry it out.
My dishwasher stopped working, panel doesn’t turn on, only the internal light turned on. Where could I found pdf of the workshop manual you mentioned ? First time try to repair something 😅. Do we have some video showing how to remove the front door? Thank you ！
Any link for the large lcd display multimeter I'd love a bigger display
👍👍👍.Thank you
It seems E-3 code is a fairly common problem for the ICUIRE brand countertop dishwasher? I was very careful with it and took care of the machine. Never loaded it without scraping the dishes first, keep the filter free of detritus and would air dry the filter and screen. I accidentally ran it without the filter and that is how I earned my E-3 code. Would appreciate a future DYI or some advice on what to look for. I will subscribe because I plan to fix this myself. Thanks in advance either way! Addendum -ICUIRE advises to tilt the machine for an approximate number of minutes if the machine registers an E-3 code. Why and what component would possibly benefit from this action?
Hi there. Thank you so much for this brilliant video. I have the same device and l would like to ask you if you know what’s wrong when the main pump doesn’t start but the timer keeps counting down…
Hi there, I get very humbled by your comment. I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well.
I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/
Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍
Thank you
great video , thanks 🙏🏻
Thanks so much for this! I have an ed fault, and it sounds like you are saying if I can't just find a loose connection replace whole machine is that correct?
Thanks so much for this, helped my find the blockage (it was corn, its always fucking corn!) and flushed it out. Had to yoink the little side tank out of the pipes, so the clamps aren't 100% but it should be fine. Will let you know in the morning!
hope everything goes well @mitchywilson9892 please remember to subscribe to our channel as that really helps us ua-cam.com/users/shortse432SAb2g08 Thanks, Paul 👍
Helo,
how to dismount the window please ? I need to clean between the 2 windows ... Thanks
I'm sorry I haven't done that yet so I don't have the information to give you correctly
Hi I'm also trying to dismount the front door. Did you ever get round to doing this? @@How-to-repair
My mum recently got a new dishwasher and gave me her countertop Klarstein mini dishwasher but it's displaying an E1 error code.
I've tried a few things suggested on youtube, such unscrewing the little panel near the inlet valve and looking for blockages. I even poked a pipe/straw cleaner in and out the inlets just in case anything was stuck.
I tried tipping the machine at an angle over the sink to try and drain the "overflow reservoir" only to have water come out of the top bit where you put the water in and it went everywhere! It didn't come out the from the front corner under the door like one video suggested XD
Nothing has worked yet, any suggestions?
I love your video, I didnt even know what an inlet valve was a couple of days ago, but it was the bane of my life trying to work it out from the manual. (Spoiler alert it doesn't tell you lol)
The manual really doesn't go into detail on what to do in case of error codes if you're not a pro or don't know the lingo, so I was just kinda like, "where the heck is the inlet valve?? What even IS an inlet valve??"
So, long story short, I now know what an inlet valve is, but I still don't know what to do to resolve the issue with it 😂
Any advice would be much appreciated! I really want to give this machine another shot, it seems like such a waste not to!
On the left-hand side once you’ve taken it all apart, there is a steam unit. I’ve seen these get blocked you only need to blow through them hard
Were you ever able to fix it?
@@nevebrown9206 I fixed it! On the inside if the dishwasher, there's a really small hole on the left wall (your left). I put vinegar in it with those measuring syringe things with a wide nozzle, you press it in quick and fast so there's pressure behind it and also i poured a bunch of vinegar in the tank with the water. If you leave it for a bit, repeat, and then run it a couple times, water starts leaking out of the small hole, and then boom, suddenly it starts working! I'm assuming it was limescale buildup. I used white wine vinegar cause that's all I had, but it might work better/ cheaper with your normal white vinegar:) be generous with it so it gets in all the nooks and crannies! I was so delighted! Can't take credit for it, a lady made a video showing how to do it, it worked and made me so happy! It's worked absolutely fine ever since
Hi, we have just randomly started having issues with our mini midea. It seems to randomly stop (at different times) during cycles, and then will just beep every minute or so. We’ve had to end up emptying the water by tilting it from the main compartment each time this has happened. No error codes are coming up. Can you help?
Check the pcb for fuse and look up the heat element
I’m having a similar problem
I don't get an error code, but every icon on my panel lights up, and it does not respond to any buttons pushed.
Thanks for your video. I didn't know there was an element to heat the water and I was supposed to only fill the tank with COLD water. I wonder if I accelerated the rate at which it broke. :(
👍
My midea display is dead. Wat kann i do?
this will either be the displayed board is not functioning or the main motherboard is not sending data. Try checking the connections on both ends.
Mini Medea - trash, toy for a year. Bucket of bolts