Twin Rotor Magnetic Motor Prototype
Вставка
- Опубліковано 20 вер 2024
- Free energy twin rotor magnetic motor. This is a prototype of a free energy twin rotor magnetic motor. We got the idea to build this from the internet. We used 2 rotors that are connected together through gears and they turn oppositely in respect to each other. Each rotor has 8 neodymium permanent magnets, each permanent magnet sits on top of a special mumetal that is supposed to help shield the back side of the permanent magnet. All permanent magnets on both rotors are facing south in the outward direction. In the center in between the 2 rotors, there is a metal ramp where the distance to the approaching magnets is greater and progressively moving closer. The permanent magnet will be attracted to it and will tend to follow the ramp up to the end of the ramp and slightly past. At this point, the permanent magnets on each rotor begin to feel each others' repulsion forces and begin to repel each other, and at the same time, new magnets are entering the metal ramp causing continuous rotation of both rotors in opposite directions. Our prototype is attempting to accelerate but after 1 to 2 minutes of rotation, slowly the rotors begin to slow down until the rotation eventually comes to a stop. From testing, we could tell that there is a lot of interaction between the 2 rotors/gears and attracting and opposing forces of the permanent magnets because a small push to get the rotation started results in a much longer rotation time. We used very little bearings and shaft for little friction, we also used some oil to reduce further friction and in the construction, we used stainless steel shaft, bearings, and screws. After testing, we believe that it might be possible for this motor to run for forever if built with a slightly different configuration. Website: mindoftesla.com
There are always a few that doubt free energy. Check this link out: ua-cam.com/video/E7wrwyRBuXY/v-deo.html. Another German patent from the 1950's. Germany took it seriously and made 20 prototypes of the same invention improving each time. They are claiming 1 to 80 percent ratio from power in to power out. It takes them 320 watts of electrical energy to manually create the timing for the permanent magnets for their huge all permanent magnet motor and they claim over 25000 watts out. Most of the free energy patents claim 1 to 3 ratio or 1 to 7 ratio of power in to power out which can use a portion of that to keep the motor going and use the rest of it to power actual loads. As for this prototype, the main goal for us was to see whether it has a potential to at least run itself without any extra power. From testing, we could tell that there is a lot of interaction between the 2 rotors/gears and attracting and opposing forces of the permanent magnets because a small push to get the rotation started results in a much longer rotation time. We used very little bearings and shaft for little friction, we also used some oil to reduce further friction and in the construction, we used stainless steel shaft, bearings, and screws. The gears are 3d printed and also have some friction, the mumetal used is supposed to help change or contain part of the reverse side of the permanent magnet to allow less interaction with the front side of the permanent magnet and reduce the opposing forces of the two rotors. A second prototype attempt of this should be a solid continuous ring of mumetal and also curved permanent magnets to go along with the curved mumetal. Patent Nr. DE3804194A1. This video is an attempt of this patent.
Eres brillante ... El q diga lo contrario es q no entiende y su nivel intelectual no alcanza a ellos le falta conocimiento antiguo de tesla carecen de ideas propias y solo repiten lo q se les a enseñado falsamente saludos amigo sigue puedes llegar muy alto
I am happy someone young is doing something for humanity. We need these technologies to move forward into the free energy revolution. Something the one percenters really would love to destroy. What is the best place you found Daniel to purchase neo magnets ?? Good day and good luck !!!!
@@victoryfirst2878 ⚠️ God has said in the Quran:
🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 )
🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 )
🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 )
🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 )
🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 )
⚠️ Quran
Am fost în telepatie? Eu m_am gândit la sistem bandă (șenilă), cu un disc din fier (dințat, dreptunghiular), sincronizat cu pasul magneților. La tine este o problemă cu vârful acelei săgeți care se agață. Trebuie renunțat la vârf.
Desființează acea pană feromagnetică pt că este frănă față de cerc. Introdu 2 in interiorul cercurilor, pt a avea 2 accelerații unghiulare.
This is somewhat similar to the 1950 free energy design called the Bowman Permanent Magnet Motor. It had 3 spinning discs and 6 sets of bearings for friction. They used old style Alnico rod magnets with one starter magnet. See also the Ecklen double horseshoe magnet motor with spinning shields and reciprocating block + springs, with power take off .
J'ai bien regardé... celle ci-dessus incomplet.. elle doit être reliés synchroniser.. pour tourner en même temps sans décalage
LA OUI SA FONCTIONNERA TRÈS BIEN... voilà
I'm glad you've rediscovered my toy.
I think we all realize that among all the Bunnings, Heath Robinson meschigger-machines and ersatz Escher engines its the only one that slaps Newton in the chops .. Mußeltov
10 лет назад такое же делал перепробывал разное...не работает
These builds take alot of time and money. Thanks for sharing your ideas.
What a nice idea unfortunately it's just for vlog purposes only just to create money,is that product already available in the market?
One question: If you can stop it with your hands, how it is possible to extract energy from it?
It would depend on how much force it would require to spin an alternator, as long as this force is less than the kinetic force, it would work, or were you to enclose the system in a copper coil or tube, the flux would need to be strong enough to counteract the diamagneticflux.
Because it's Magic!!
sure u can... just wear a glove to avoid injury from the pointed teeth of the sprockets
Put a fan on it.... 😏
I was thinking the same thing. It must have a sweet spot that has an equal amount of push / pull, or it's very weak.
This doesn't work, you can see at 1:43 it slows down. I reckon he was using compressed air to keep it moving. Let us hear the original sound.
No need for compressed air probably an electric motor
@@big_o1952 I don't see any evidence of wires or batteries, so compressed air was the simplest way to keep it moving in my mind.
" braaaaaaaang "
Je confirme à 100/100 que sa fonctionne ont peut le faire moins chère..je le C très bien... j'ai fabriqué..
Pour vous bravo
Enorme ! Oui je pense que la clé est dans le blindage !
@@henridecorbiac2239 bonjour.... le blindage vous pouvez rusé lame de fer doux épaisseur pareillement que dès lame transformateur.... sa arrête très efficace le champ magnétique coupe sa remplace l'iridium à moindre frais pour le même résultat blindage enti magnétique VRAIMENT PAS CHÈRE PLUS
just say this thing did work why would we not use it now days to have infinite energy think about logically
Add gear box on back with flywheel and in the front add some coils for electricity generation.
Will it run until you stop it? What's the longest you let it run?
The real test to check if these inventions are 'perpetual' or fake is that they should rotate themselves without being pushed. If they are rotated by hand and then stopped by hand they should start rotating again.
It would work if we could somehow deviate the magnetic poles a little bit to the side. Like building some things that would automatically rotate the magnet a little bit on the nearest point.
Don't waste your time!
Continuando a ruotare, i perni delle due pulegge dovrebbero riscaldarsi per attrito. Questa energia termica da dove proviene? Non capisco.
This would've been better if the wedge doesn't conduct electric or eddy currents and let the offset repulse the magnets.
I built one like this using aluminum gears and wood about 15 years ago . Mumedal was not available when I built it nor did not know where to look for it in old PC’s. I knew it would work if I could have only gotten past the resistance of the on coming mags.
Think I’ll give it another try. Thanks
There is no Mu-metal, it's all bullshit.
Es necesario el engranaje?
When I tried this the rotors stop as there is always some point where attraction and repulsion balance each other. There is nothing to make the rotors continue to turn.
A usted no le funciona ya q el es un árbol de roble y usted al lado de el es solo un arbusto el muchacho es un genio no tengo mas q decir ya q yo tengo sistemas de cop mayor q 1 ninguna duda de lo brillante q es daniel
Pentru că nu adecvăm masa de inerție și aplicăm pe exteriorul cercurilor care este frănă. Din interior ar avea accelerație unghiulară. Iar o forță de respingere este mai mică decât una de atracție cu de 2 ori atracția pe un feroaliaj.
It would work if we could somehow deviate the magnetic poles a little bit to the side. Like building some things that would automatically rotate the magnet a little bit on the nearest point.
@@constantinvasile2964 este posibil sa creezi energiei infinita cu ajutorul magnetilor?
we can always use a motor with a battery to ensure it keeps spinning, maybe add a solar panel to recharge the battery as it is depleted😁
Danny boy, why don't you use a little motor that prevents the magnet from being trapped in some unstable balance of the bipolarity of the magnets?
The right name is the one minute auto stop engine.
maybe have the two magnets in the center, that meet closest, push off each other, pushing in a inward spring, then when they roll on a little, the springs can come back out when aimed down, giving an extra free push.
Anyone looking to build an experiment? I've got three ideas that I need to test but I don't have the raw materials.
Counting down
Idea-3
I tried this idea out with fidget spinners and it sort of worked. The fidget spinners had three arms and on the first spinner I sellotaped a ring(doughnut) magnet to each arm, in a vertical position, so that when the arm was at 12 o'clock the right side of the magnet was always a North. I then stuck three ring magnets flat on the arms of the second fidget spinner so that North was pointing upward. I span the first spinner horizontally anti-clockwise and the second spinner I held next to the right side but in a vertical position spinning clockwise. When they were in synch, the magnet on the second spinner would always be behind the horizontal spinner. So for example, when the first spinner had a magnet at one o'clock, the second spinner would have a magnet at 7 o'clock, then as they repelled each other the bottom horizontal spinner would speed up. The problem was that the vertical spinner had nothing driving it because the repulsion was on the horizontal. The vertical would slow and fall out of sync and then attract to the South of one of the bottom magnets.
I needed for the spinners to stay in sync and thought what if they were flat round cogs beveled at 90 degrees to each other. I could use two magnets per cog and when the vertical cog's magnet pushed the bottom horizontal cog round that would in turn drive the vertical cog.
I got some cogs from a toyset but they were too small and the cog teeth didn't fit very well. I went to the local library but their 3d printer could only do tiny cogs.
So I'm stuck.
I also wanted to try a configuration where the horizontal cog had two magnets but the vertical cog had a magnet in a sort of slide, so that it was always sliding down into position as the cog turned.
Idea 2 - You have a vertical tube that spins around a centre point, it could also be a tube attached to a disc that spins. At either end of the tube are 'balloons' and the whole thing is filled with ferrofluid. At about the 1 or 2 o'clock position, the top balloon goes near a fixed magnet. The magnet starts to pull ferrofluid into the top balloon which expands pulling more of the fluid into it. The balloons are not globe shaped as we don't want them touching the magnet and 'sticking'. The balloons are a flat shape like a blow up mattress and when the top balloon is full it becomes too heavy for the magnet and falls down, which turns the disc and brings the bottom balloon up to the magnet and the whole thing starts again.
This is a very stop start motion but it could be used to power a flywheel. Also, to stop the ferrofluid falling back down the tube as the balloon is nearly full we could have two tubes with one-way valves inside. The tubes would have different flow directions and when the top balloon is first trapped by the magnet we could have a rocker switch which cuts off flow to the down tube and only allows flow through the up tube, which has one-way valves to stop the fluid falling back down. Hopefully this last part won't be necessary. (Got a version of this experiment with water instead of ferrofluid buts that's even more awkward. The balloons are covered with metal discs that get further away from each other as the balloon expands making the balloon less 'metalic'. So the magnets have less hold as the balloon gets heavier and finally drops).
Idea 1- Take a reservoir of ferrofluid and put a glass tube into it. The glass tube is shaped like a walking cane with a curved end. The straight end goes into the ferrofluid, the tube is angled upward at say 45 degrees and a magnet is placed underneath the curved end(the ferrofluid should drop vertically here so the tube should be curved just enough to do this). The tube will need to be full of ferrofluid before the experiment starts. The ferrofluid should be pulled down onto the magnet to form a spikey ball which will get too big for the magnet to support, when this happens the ferrofluid will drip into a second reservoir which is higher than the first. The ferrofluid in the upper reservoir can then be dropped down a tube onto a plastic turbine. To make sure the top reservoir fills up at the same speed as the bottom one does, you could have a thousands of tubes pulling the fluid up for every one downtube powering a turbine. This could be upscaled and built in a disused mine.
But first I need to see if a magnet can pull the ferrofluid up through the walking cane shaped tube.
Wouldn't the attraction to the metal get canceled by the magnet on the opposite side? 😄
Very nice!
What is the RPM?
Also does it encounter the problem of an increasing magnetic wall after a few rotations - that then reverses the entire magnetic field of the device and stops it?
Depinde de sensul de rotație.
All the other builds have failed. Why does yours work?
For 15 years, I have been working with angular resonance and I am ready to do the electricity generation project together with investors who agree to make an official protocol. Everything will be done openly after the signatures are signed.
You need to hook up wires to metal or copper coils to harvest the eddy current caused by the magnetic field motion through the coil
A magnet can’t create energy, using a magnet is like using a spring or gravity, it restitute the force you add in it. Your system use the energy you add to initiate the movement with your hand, then friction and other forces make it stop by itself because no other energy is added to compensate the loss. It is easy to understand :-)
look up john roney stators, no gimmick but hes close to something
Very smart, but unfortunately still incompleted against Law's of Thermodynamic.
Lol
perché il mumetal?
perché non usare esclusivamente magneti?
You might want to try thick straps of copper in place of the steel attractors.
Better still, a copper aluminium laminate easily made from merchandise at your model/RC shop
I figured this would work
glad to see some one try it
thank you🙂
Can you remove the gears and decrease the air gap between the two rotors?
Yes that is convincing and simple design👌👍,try to replace flat bar by solid steel
O bară masiva și tablă subțire în forma literei t intors.
This can’t work because the magnets would settle in one position as there a magnets top and bottom so it would cancel out any force so fake
besides replacing the steel attractors with Cu/Al laminate you'll need to add an escapement to either shaft .. runaway speed will produce catastrophic magnetic eddies
Copper and aluminium is not attracting the magnets, so how would that work?
you're a genius, tesla i nothing
the hardest part about making a free energy is where to hide the battery
Does this work?
As I've tried this &spend some amount,but didn't work
I have doubts when the labeling has N as blue and S as red. Seems purposeful misleading.
the 5 secs gave away .... once the setup starts running ... no matter what, it will not stop till magnetism is zero - but when you stopped it and took your hands off .. it should have started again ....but it did not .... lol ... better luck next time.
WELL DONE !!!!
YES I TRIED THIS ONE TOO...... I WONDER WHAT WILL HAPPEN IF YOU ADD A METAL BAND ON THE OUTER PERIMETER OF THE TWO WHEELS WITH THE METAL GRADUALY COMMING CLOSER TO THE MAGNETS AND CLOSER TO THE PINCH POINT IN THE MIDDLE....NATURALLY THE MAGNETS WILL TEND TO MOVE TO THE POINT NEAREST THE METAL OUTER RINGS AND POSSIBLY ASSIST IN GETTING PAST THE STICKY POINT IN THE MIDDLE.....HOWEVER THERE MIGHT BE A BRAKING EFFECT DUE TO THE EDDY CURRENTS CAUSED BY THE MAGNETS ON THE METAL PLATES.
Nu. Se produce frăna pirueti la patinaj. Nu pe exteriorul cercului, ci în interior pentru a avea accelerație unghiulară.
It must be mumetal or similar, iron will produce huge amounts of eddy currents that will stop the weels to spin completely.
Your content is highly appreciated and I'm inspired to do my own stuff, thank you.
Very nice is it for sale? Like to buy it
at 1:35 where you show a the magnetic poles , the opposing south poles from each wheel in the top section do repel each other to cause rotation , but you somehow claim that the same opposing poles at the bottom of the wheel , where they are coming closer from rotation somehow have an attracting force !!!!!! ............ thats why this does not work
That iron should be mumetal..
This is the future.
Every house should have their own mini electric plant
It would have to actually work for that. It even says in the description it doesn’t work.
Free energy is real - I have verified some mechanisms, but this one will not work
Ok, where are they?
And where is your Nobel prize lol.
Very nice!!!!
Interesting Design
sin caños de hierro más magnetismo .
1-2 minute are great to start..what if magnets of one side is shorter than other side so it can push other side by right point..IDK..just curriouse.
Tx for uploading
Это будет лучше вращатся с мощными магнитами силой сцепления от 30 кг,а ещё лучше работают на сдвиг вдоль оси ,как подумайте,если расположить диски на одном валу ,потери 15 процентов
The whole thing is fake
Ola tudo bem ? Eu ainda nao fiz mais é bastante convincente que funcione
i've try it and doesn't work, any suggestion?
get a solar panel
Read a physics book and stop wasting your time.
Maybe these magnet motors designs need to focus more on being asymmetrical and not symmetrical imo.
If I knew this, I gonna make bike engine with this 😊😊😊
let's hope cars can run on it
The distance between the two is how many cm
This is the exact idea I had in my head
Și eu la fel, dar cu bandă și un disc perpendicular cu dinți pătrați, sincronizat.
only thing now you need is a dc motor to keep it spinning
I need this model.
How to buy. Please guide me
Please can you make one for me and how much would it be? Please!!!!!
What is the torque??
If it really works u are a genius I will try make one n put to use.
And the point of the mew blocks is what? Exactly I mean the way they're applied here just makes no sense to me whatsoever I mean I guess it doesn't matter since the whole thing is ridiculous but just that part I'm curious about
im sorry for you, you do your best to get a good over unity thing but not always it works.
이것은
안 됩니다.
같은 극끼리
만날 수 있는데
까지 도달 할 수
있는것은 흡작판을
극과 극 사이이 있
습니다.
양극은 자성체를
타고 만나게 되는
장치인데
양극은 자성체를
당기려는 힘이 더
커 집니다.
고로 양극은 자성
체를 벗어날 수 없으며
서로 마주 할 수도
없습니다.
Free energy for all the world! You dont need anymore petroleum or gas.
Is that a declaration or an observation? He says in the description it doesn’t work.
Moi j'ai toujours pensé qu'il faudra associer plusieurs technologies en parallèle pour obtenir un résultat probant
Magnete gehen kaputt wenn gleiche pole aufeinander gerichtet sind.
Use a ceramic ball berings its has smaller drag.
I think it could use something like the spinning thing on top of steam engines n boilers that regulates the speed n pressure (if that's what it does... IDK, I'm sure it's not there cause it looks cool)...
A thing that raises n lowers the pointy end of the metal ramp...with weights, springs, or magnets...
Un disc perpendicular dințat cu formă pătrată, sincronizat cu pasul magneților.
Daniel, do you think that you could make something that could produce electricity just using magnets ??? Please drop a line with an answer Sir. Thanks
Com certeza isso viria com patente
@@dionatanmunhoz7847 English please
It is fake
@@big_o1952 I have seen one of these at a engine show running. I checked it out and stopped it and started the same machine. Their is a difference between just running and making power from the item.
solar powers and wind generators are the closest we can get to free energy other than invading oil rich countries
There's so many ideas it will spend but you can't put a load on it . It hase to be massive size and super heavy flighwheels to put a small amount of energy load . . Do it bigger and and try to put a load on it 🤔👍🏼
This video is a Patent from German Inventor Guenter Rensmeyer, Patent Nr. DE3804194A1 . He says the intermediate plate is made of magnetic material which is also a superconductor
Thanks for pointing that out. We could not find the exact patent number.
@@DanielsInventions mas ele para de funcionar
It is not possible what you are showing is a fake video
What you think about antigravity?
Science fiction.
What is the shielding material in between
Is it shielding? Or is it there to attract the magnets that is coming towards it?
All of these YouEinsteins use compressed air to spin wheels so don't waste your time
nope.....it doesn t work
Ideia interessante. Pena que não funciona!
Porque não funciona ? Ele não está extraindo energia do sistema fechado para alimentar outra coisa. Isso é a mesma coisa dos sistemas contínuos de pêndulos, que giram mas não produzem energia extra.
This will work, but the torque it produces will be very less.
Ok felicitări
Trebuie un sistem mai greu sau diametre mai mari cu distanțe mai mari între magneți, min. 30 cm. de pe fiecare disc.
Add a flywheel
on my channel really working gravity engine
Where did you get those magnets?
Magnet store
What if we are demagnetizing the magnets? The Movement (or energy) that we obtain can come from the demagnetization.
Interesting idea, I've seen some magnetic motor lift mounts that can "turn off" by rotating a lever, it works by cancelling out the polarity, wonder if something like that could be employed with the rotation to help avoid the deadspots / attraction points 🤔
Would it be considered " perpetual"
Even if the design worked without BS (I have doubts), a permanent magnet will eventually deplete. So no, not truly perpetual.
@@gregoirepainchaud I'm curious. Does a permanent magnet deplete over time without use or does it deplete only with use. Maybe both? If you know I would appreciate the education. Thanks.
오~~굿 아이디어...
Diameters how many cm
How much?
There is no free energy
So after all of this success, does any of your "toys" actually gives you an electricity? Are you free of the grid? Aside from the fact that you giving us great ideas, though we're very thankful on that, do you replying on any questions posed to you?
😁
He says in the description it doesn’t work.
= a water maker?
we can have free energy, a globe within a globe within a globe, mimicking the earth's core, if you look at the cutaway of the earth, it looks like, layer-layer-layer. then it copies-copies-copies-then it repeats-repeats-repeats. the power of 3,, each globe has 3 laters of polished nickel, with magnets, creates a magnetic energy wave, each globe rotates opposite than the other, this creates a "constant rotational surface", the energy wave creates a light, add a Gyroscope to the outside driven by the rotation of the globes, will create an "engine" that can go to outer space or to the bottom of the ocean, add programmable nanotech and it could possibly be able to create true hard water, it could remake the glaciers, it could possibly help to re-create the underwater rivers of the oceans that cool off the planet that the glaciers were feeding. we have the parts and the tech, it just has NEVER been put together like this !!
Does anyone want to help me refine this one
done watching show us the batteries now